[PATCH v2 00/10] Support ROHM BD96801 Scalable PMIC

[PATCH v2 00/10] Support ROHM BD96801 Scalable PMIC

[Matti Vaittinen]

[-- Attachment #1: Type: text/plain, Size: 5219 bytes --]

Support ROHM BD96801 Scalable PMIC

The ROHM BD96801 is automotive grade PMIC, intended to be usable in
multiple solutions. The BD96801 can be used as a stand-alone, or together
with separate 'companion PMICs'. This modular approach aims to make this
PMIC suitable for various use-cases.

This series brings only limited support. The more complete set of
features was sent in the RFC:
https://lore.kernel.org/lkml/cover.1712058690.git.mazziesaccount@gmail.com/

The BD96801 provides two physical IRQ lines called "intb" and "errb" in
the data-sheet. These are handled using own regmap-IRQ controller for
both of the IRQ lines. This causes a debugFS naming conflict for IRQ
domains created by the regmap-IRQ. This series adds support for setting
a name suffix to IRQ domains. Some prior discussion can be seen here:
https://lore.kernel.org/all/Zjzt8mOW6dO_7XNV@finisterre.sirena.org.uk/

As writing of this there is no known system doing configurations which
require the PMIC to be in STBY state using Linux driver. Furthermore,
ensuring the PMIC is and stays in the STBY state when configurations
are done may not be trivial. Especially, not in a generic way in a
regulator driver. This is likely to be system specific.

Hence it felt natural to upstream only partial support for
now, while leaving a note about the RFC series with more complete
support for those who may need it later.

The patches from 1 to 6 are just typical "add support for device X"
stuff. They should provide very much usable driver for BD96801 and I
hope they don't cause too many questions and can be merged when
quality seems high enough :)

Supporting the ERRB IRQ (patches 9 and 10) requires the regmap IRQ change
(patch 8) which further requires the IRQ domain change (patch 7).

Patches 7 and 8 may need more careful thinking. Thus, the ERRB IRQ
support is added as a separate step, which can be merged later or even
dropped if the irqdomain changes prove to be unacceptable.

Revision history still tries to summarize changes from the RFC for the
reviewers.

Revision history:
v1 => v2:
	- Add support for setting a name suffix for fwnode backed IRQ domains.
	- Add support for setting a domain name suffix for regmap-IRQ.
	- Add handling of ERRB IRQs.
	- Small fixes based on feedback.

RFCv2 => v1:
	- Drop ERRB IRQ from drivers (but not DT bindings).
	- Drop configuration which requires STBY - state.
	- Fix the register lock race by moving it from the regulator
	  driver to the MFD driver.

RFCv1 => RFCv2:
	- Tidying code based on feedback form Krzysztof Kozlowski and
	  Lee Jones.
	- Documented undocumented watchdog related DT properties.
	- Added usage of the watchdog IRQ.
	- Use irq_domain_update_bus_token() to work-around debugFS name
	  collision for IRQ domains.

---

Matti Vaittinen (10):
  dt-bindings: ROHM BD96801 PMIC regulators
  dt-bindings: mfd: bd96801 PMIC core
  mfd: support ROHM BD96801 PMIC core
  regulator: bd96801: ROHM BD96801 PMIC regulators
  watchdog: ROHM BD96801 PMIC WDG driver
  MAINTAINERS: Add ROHM BD96801 'scalable PMIC' entries
  irqdomain: Allow giving name suffix for domain
  regmap: Allow setting IRQ domain name suffix
  mfd: bd96801: Add ERRB IRQ
  regulator: bd96801: Add ERRB IRQ

 .../bindings/mfd/rohm,bd96801-pmic.yaml       |  173 +++
 .../regulator/rohm,bd96801-regulator.yaml     |   63 ++
 MAINTAINERS                                   |    4 +
 drivers/base/regmap/regmap-irq.c              |   13 +-
 drivers/mfd/Kconfig                           |   13 +
 drivers/mfd/Makefile                          |    1 +
 drivers/mfd/rohm-bd96801.c                    |  488 ++++++++
 drivers/regulator/Kconfig                     |   12 +
 drivers/regulator/Makefile                    |    2 +
 drivers/regulator/bd96801-regulator.c         | 1008 +++++++++++++++++
 drivers/watchdog/Kconfig                      |   13 +
 drivers/watchdog/Makefile                     |    1 +
 drivers/watchdog/bd96801_wdt.c                |  416 +++++++
 include/linux/irqdomain.h                     |   28 +-
 include/linux/mfd/rohm-bd96801.h              |  215 ++++
 include/linux/mfd/rohm-generic.h              |    1 +
 include/linux/regmap.h                        |    4 +
 kernel/irq/irqdomain.c                        |   53 +-
 18 files changed, 2487 insertions(+), 21 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd96801-pmic.yaml
 create mode 100644 Documentation/devicetree/bindings/regulator/rohm,bd96801-regulator.yaml
 create mode 100644 drivers/mfd/rohm-bd96801.c
 create mode 100644 drivers/regulator/bd96801-regulator.c
 create mode 100644 drivers/watchdog/bd96801_wdt.c
 create mode 100644 include/linux/mfd/rohm-bd96801.h


base-commit: 4cece764965020c22cff7665b18a012006359095
-- 
2.45.1


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

[PATCH v2 05/10] watchdog: ROHM BD96801 PMIC WDG driver

[Matti Vaittinen]

[-- Attachment #1: Type: text/plain, Size: 14337 bytes --]

Introduce driver for WDG block on ROHM BD96801 scalable PMIC.

This driver only supports watchdog with I2C feeding and delayed
response detection. Whether the watchdog toggles PRSTB pin or
just causes an interrupt can be configured via device-tree.

The BD96801 PMIC HW supports also window watchdog (too early
feeding detection) and Q&A mode. These are not supported by
this driver.

Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>

---
Revision history:
v1 => v2:
- Drop the forward declaration for emergency_reboot()
- Typofixes
- Do error checks before assignments in find_closest_fast()
- Improve prints for unsupported (HW) timeout values
- Use FIELD_GET() and FIELD_PREP()
- Use error severity when unsupported Q&A WDG mode is tried to be used.
- Minor styling fixes

RFCv2 => v1:
- Fix watchdog time-outs to match DS4
- Fix target timeout overflow
- Improve dbg prints

RFCv1 => RFCv2:
- remove always running
- add IRQ handling
- call emergency_restart()
- drop MODULE_ALIAS and add MODULE_DEVICE_TABLE

watchdog: bd96801: styling fix
---
 drivers/watchdog/Kconfig       |  13 ++
 drivers/watchdog/Makefile      |   1 +
 drivers/watchdog/bd96801_wdt.c | 416 +++++++++++++++++++++++++++++++++
 3 files changed, 430 insertions(+)
 create mode 100644 drivers/watchdog/bd96801_wdt.c

diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
index 6bee137cfbe0..d97e735e1faa 100644
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -181,6 +181,19 @@ config BD957XMUF_WATCHDOG
 	  watchdog. Alternatively say M to compile the driver as a module,
 	  which will be called bd9576_wdt.
 
+config BD96801_WATCHDOG
+	tristate "ROHM BD96801 PMIC Watchdog"
+	depends on MFD_ROHM_BD96801
+	select WATCHDOG_CORE
+	help
+	  Support for the watchdog in the ROHM BD96801 PMIC. Watchdog can be
+	  configured to only generate IRQ or to trigger system reset via reset
+	  pin.
+
+	  Say Y here to include support for the ROHM BD96801 watchdog.
+	  Alternatively say M to compile the driver as a module,
+	  which will be called bd96801_wdt.
+
 config CROS_EC_WATCHDOG
 	tristate "ChromeOS EC-based watchdog"
 	select WATCHDOG_CORE
diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
index 3710c218f05e..31bc94436c81 100644
--- a/drivers/watchdog/Makefile
+++ b/drivers/watchdog/Makefile
@@ -217,6 +217,7 @@ obj-$(CONFIG_XEN_WDT) += xen_wdt.o
 
 # Architecture Independent
 obj-$(CONFIG_BD957XMUF_WATCHDOG) += bd9576_wdt.o
+obj-$(CONFIG_BD96801_WATCHDOG) += bd96801_wdt.o
 obj-$(CONFIG_CROS_EC_WATCHDOG) += cros_ec_wdt.o
 obj-$(CONFIG_DA9052_WATCHDOG) += da9052_wdt.o
 obj-$(CONFIG_DA9055_WATCHDOG) += da9055_wdt.o
diff --git a/drivers/watchdog/bd96801_wdt.c b/drivers/watchdog/bd96801_wdt.c
new file mode 100644
index 000000000000..ff51f42ced2a
--- /dev/null
+++ b/drivers/watchdog/bd96801_wdt.c
@@ -0,0 +1,416 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2024 ROHM Semiconductors
+ *
+ * ROHM BD96801 watchdog driver
+ */
+
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/rohm-bd96801.h>
+#include <linux/mfd/rohm-generic.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/reboot.h>
+#include <linux/regmap.h>
+#include <linux/watchdog.h>
+
+static bool nowayout;
+module_param(nowayout, bool, 0);
+MODULE_PARM_DESC(nowayout,
+		"Watchdog cannot be stopped once started (default=\"false\")");
+
+#define BD96801_WD_TMO_SHORT_MASK	0x70
+#define BD96801_WD_RATIO_MASK		0x3
+#define BD96801_WD_TYPE_MASK		0x4
+#define BD96801_WD_TYPE_SLOW		0x4
+#define BD96801_WD_TYPE_WIN		0x0
+
+#define BD96801_WD_EN_MASK		0x3
+#define BD96801_WD_IF_EN		0x1
+#define BD96801_WD_QA_EN		0x2
+#define BD96801_WD_DISABLE		0x0
+
+#define BD96801_WD_ASSERT_MASK		0x8
+#define BD96801_WD_ASSERT_RST		0x8
+#define BD96801_WD_ASSERT_IRQ		0x0
+
+#define BD96801_WD_FEED_MASK		0x1
+#define BD96801_WD_FEED			0x1
+
+/* 1.1 mS */
+#define FASTNG_MIN			11
+#define FASTNG_MAX_US			(100 * FASTNG_MIN << 7)
+#define SLOWNG_MAX_US			(16 * FASTNG_MAX_US)
+
+#define BD96801_WDT_DEFAULT_MARGIN_MS	1843
+/* Unit is seconds */
+#define DEFAULT_TIMEOUT 30
+
+/*
+ * BD96801 WDG supports window mode so the TMO consists of SHORT and LONG
+ * timeout values. SHORT time is meaningful only in window mode where feeding
+ * period shorter than SHORT would be an error. LONG time is used to detect if
+ * feeding is not occurring within given time limit (SoC SW hangs). The LONG
+ * timeout time is a multiple of (2, 4, 8 or 16 times) the SHORT timeout.
+ */
+
+struct wdtbd96801 {
+	struct device		*dev;
+	struct regmap		*regmap;
+	struct watchdog_device	wdt;
+};
+
+static int bd96801_wdt_ping(struct watchdog_device *wdt)
+{
+	struct wdtbd96801 *w = watchdog_get_drvdata(wdt);
+
+	return regmap_update_bits(w->regmap, BD96801_REG_WD_FEED,
+				  BD96801_WD_FEED_MASK, BD96801_WD_FEED);
+}
+
+static int bd96801_wdt_start(struct watchdog_device *wdt)
+{
+	struct wdtbd96801 *w = watchdog_get_drvdata(wdt);
+
+	return regmap_update_bits(w->regmap, BD96801_REG_WD_CONF,
+				  BD96801_WD_EN_MASK, BD96801_WD_IF_EN);
+}
+
+static int bd96801_wdt_stop(struct watchdog_device *wdt)
+{
+	struct wdtbd96801 *w = watchdog_get_drvdata(wdt);
+
+	return regmap_update_bits(w->regmap, BD96801_REG_WD_CONF,
+				  BD96801_WD_EN_MASK, BD96801_WD_DISABLE);
+}
+
+static const struct watchdog_info bd96801_wdt_info = {
+	.options	= WDIOF_MAGICCLOSE | WDIOF_KEEPALIVEPING |
+			  WDIOF_SETTIMEOUT,
+	.identity	= "BD96801 Watchdog",
+};
+
+static const struct watchdog_ops bd96801_wdt_ops = {
+	.start		= bd96801_wdt_start,
+	.stop		= bd96801_wdt_stop,
+	.ping		= bd96801_wdt_ping,
+};
+
+static int find_closest_fast(unsigned int target, int *sel, unsigned int *val)
+{
+	unsigned int window = FASTNG_MIN;
+	int i;
+
+	for (i = 0; i < 8 && window < target; i++)
+		window <<= 1;
+
+	if (i == 8)
+		return -EINVAL;
+
+	*val = window;
+	*sel = i;
+
+	return 0;
+}
+
+static int find_closest_slow_by_fast(unsigned int fast_val, unsigned int *target,
+				     int *slowsel)
+{
+	static const int multipliers[] = {2, 4, 8, 16};
+	int sel;
+
+	for (sel = 0; sel < ARRAY_SIZE(multipliers) &&
+	     multipliers[sel] * fast_val < *target; sel++)
+		;
+
+	if (sel == ARRAY_SIZE(multipliers))
+		return -EINVAL;
+
+	*slowsel = sel;
+	*target = multipliers[sel] * fast_val;
+
+	return 0;
+}
+
+static int find_closest_slow(unsigned int *target, int *slow_sel, int *fast_sel)
+{
+	static const int multipliers[] = {2, 4, 8, 16};
+	unsigned int window = FASTNG_MIN;
+	unsigned int val = 0;
+	int i, j;
+
+	for (i = 0; i < 8; i++) {
+		for (j = 0; j < ARRAY_SIZE(multipliers); j++) {
+			unsigned int slow;
+
+			slow = window * multipliers[j];
+			if (slow >= *target && (!val || slow < val)) {
+				val = slow;
+				*fast_sel = i;
+				*slow_sel = j;
+			}
+		}
+		window <<= 1;
+	}
+	if (!val)
+		return -EINVAL;
+
+	*target = val;
+
+	return 0;
+}
+
+static int bd96801_set_wdt_mode(struct wdtbd96801 *w, unsigned int hw_margin,
+			       unsigned int hw_margin_min)
+{
+	int fastng, slowng, type, ret, reg, mask;
+	struct device *dev = w->dev;
+
+
+	if (hw_margin_min * 1000 > FASTNG_MAX_US) {
+		dev_err(dev, "Unsupported fast timeout %u uS [max %u]\n",
+			hw_margin_min * 1000, FASTNG_MAX_US);
+
+		return -EINVAL;
+	}
+
+	if (hw_margin * 1000 > SLOWNG_MAX_US) {
+		dev_err(dev, "Unsupported slow timeout %u uS [max %u]\n",
+			hw_margin * 1000, SLOWNG_MAX_US);
+
+		return -EINVAL;
+	}
+
+	/*
+	 * Convert to 100uS to guarantee reasonable timeouts fit in
+	 * 32bit maintaining also a decent accuracy.
+	 */
+	hw_margin *= 10;
+	hw_margin_min *= 10;
+
+	if (hw_margin_min) {
+		unsigned int min;
+
+		type = BD96801_WD_TYPE_WIN;
+		dev_dbg(dev, "Setting type WINDOW 0x%x\n", type);
+		ret = find_closest_fast(hw_margin_min, &fastng, &min);
+		if (ret)
+			return ret;
+
+		ret = find_closest_slow_by_fast(min, &hw_margin, &slowng);
+		if (ret) {
+			dev_err(dev,
+				"can't support slow timeout %u uS using fast %u uS. [max slow %u uS]\n",
+				hw_margin * 100, min * 100, min * 100 * 16);
+
+			return ret;
+		}
+		w->wdt.min_hw_heartbeat_ms = min / 10;
+	} else {
+		type = BD96801_WD_TYPE_SLOW;
+		dev_dbg(dev, "Setting type SLOW 0x%x\n", type);
+		ret = find_closest_slow(&hw_margin, &slowng, &fastng);
+		if (ret)
+			return ret;
+	}
+
+	w->wdt.max_hw_heartbeat_ms = hw_margin / 10;
+
+	fastng = FIELD_PREP(BD96801_WD_TMO_SHORT_MASK, fastng);
+
+	reg = slowng | fastng;
+	mask = BD96801_WD_RATIO_MASK | BD96801_WD_TMO_SHORT_MASK;
+	ret = regmap_update_bits(w->regmap, BD96801_REG_WD_TMO,
+				 mask, reg);
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(w->regmap, BD96801_REG_WD_CONF,
+				 BD96801_WD_TYPE_MASK, type);
+
+	return ret;
+}
+
+static int bd96801_set_heartbeat_from_hw(struct wdtbd96801 *w,
+					 unsigned int conf_reg)
+{
+	int ret;
+	unsigned int val, sel, fast;
+
+	/*
+	 * The BD96801 supports a somewhat peculiar QA-mode, which we do not
+	 * support in this driver. If the QA-mode is enabled then we just
+	 * warn and bail-out.
+	 */
+	if ((conf_reg & BD96801_WD_EN_MASK) != BD96801_WD_IF_EN) {
+		dev_err(w->dev, "watchdog set to Q&A mode - exiting\n");
+		return -EINVAL;
+	}
+
+	ret = regmap_read(w->regmap, BD96801_REG_WD_TMO, &val);
+	if (ret)
+		return ret;
+
+	sel = FIELD_GET(BD96801_WD_TMO_SHORT_MASK, val);
+	fast = FASTNG_MIN << sel;
+
+	sel = (val & BD96801_WD_RATIO_MASK) + 1;
+	w->wdt.max_hw_heartbeat_ms = (fast << sel) / USEC_PER_MSEC;
+
+	if ((conf_reg & BD96801_WD_TYPE_MASK) == BD96801_WD_TYPE_WIN)
+		w->wdt.min_hw_heartbeat_ms = fast / USEC_PER_MSEC;
+
+	return 0;
+}
+
+static int init_wdg_hw(struct wdtbd96801 *w)
+{
+	u32 hw_margin[2];
+	int count, ret;
+	u32 hw_margin_max = BD96801_WDT_DEFAULT_MARGIN_MS, hw_margin_min = 0;
+
+	count = device_property_count_u32(w->dev->parent, "rohm,hw-timeout-ms");
+	if (count < 0 && count != -EINVAL)
+		return count;
+
+	if (count > 0) {
+		if (count > ARRAY_SIZE(hw_margin))
+			return -EINVAL;
+
+		ret = device_property_read_u32_array(w->dev->parent,
+						     "rohm,hw-timeout-ms",
+						     &hw_margin[0], count);
+		if (ret < 0)
+			return ret;
+
+		if (count == 1)
+			hw_margin_max = hw_margin[0];
+
+		if (count == 2) {
+			if (hw_margin[1] > hw_margin[0]) {
+				hw_margin_max = hw_margin[1];
+				hw_margin_min = hw_margin[0];
+			} else {
+				hw_margin_max = hw_margin[0];
+				hw_margin_min = hw_margin[1];
+			}
+		}
+	}
+
+	ret = bd96801_set_wdt_mode(w, hw_margin_max, hw_margin_min);
+	if (ret)
+		return ret;
+
+	ret = device_property_match_string(w->dev->parent, "rohm,wdg-action",
+					   "prstb");
+	if (ret >= 0) {
+		ret = regmap_update_bits(w->regmap, BD96801_REG_WD_CONF,
+				 BD96801_WD_ASSERT_MASK,
+				 BD96801_WD_ASSERT_RST);
+		return ret;
+	}
+
+	ret = device_property_match_string(w->dev->parent, "rohm,wdg-action",
+					   "intb-only");
+	if (ret >= 0) {
+		ret = regmap_update_bits(w->regmap, BD96801_REG_WD_CONF,
+				 BD96801_WD_ASSERT_MASK,
+				 BD96801_WD_ASSERT_IRQ);
+		return ret;
+	}
+
+	return 0;
+}
+
+static irqreturn_t bd96801_irq_hnd(int irq, void *data)
+{
+	emergency_restart();
+
+	return IRQ_NONE;
+}
+
+static int bd96801_wdt_probe(struct platform_device *pdev)
+{
+	struct wdtbd96801 *w;
+	int ret, irq;
+	unsigned int val;
+
+	w = devm_kzalloc(&pdev->dev, sizeof(*w), GFP_KERNEL);
+	if (!w)
+		return -ENOMEM;
+
+	w->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+	w->dev = &pdev->dev;
+
+	w->wdt.info = &bd96801_wdt_info;
+	w->wdt.ops =  &bd96801_wdt_ops;
+	w->wdt.parent = pdev->dev.parent;
+	w->wdt.timeout = DEFAULT_TIMEOUT;
+	watchdog_set_drvdata(&w->wdt, w);
+
+	ret = regmap_read(w->regmap, BD96801_REG_WD_CONF, &val);
+	if (ret)
+		return dev_err_probe(&pdev->dev, ret,
+				     "Failed to get the watchdog state\n");
+
+	/*
+	 * If the WDG is already enabled we assume it is configured by boot.
+	 * In this case we just update the hw-timeout based on values set to
+	 * the timeout / mode registers and leave the hardware configs
+	 * untouched.
+	 */
+	if ((val & BD96801_WD_EN_MASK) != BD96801_WD_DISABLE) {
+		dev_dbg(&pdev->dev, "watchdog was running during probe\n");
+		ret = bd96801_set_heartbeat_from_hw(w, val);
+		if (ret)
+			return ret;
+
+		set_bit(WDOG_HW_RUNNING, &w->wdt.status);
+	} else {
+		/* If WDG is not running so we will initializate it */
+		ret = init_wdg_hw(w);
+		if (ret)
+			return ret;
+	}
+
+	dev_dbg(w->dev, "heartbeat set to %u - %u\n",
+		w->wdt.min_hw_heartbeat_ms, w->wdt.max_hw_heartbeat_ms);
+
+	watchdog_init_timeout(&w->wdt, 0, pdev->dev.parent);
+	watchdog_set_nowayout(&w->wdt, nowayout);
+	watchdog_stop_on_reboot(&w->wdt);
+
+	irq = platform_get_irq_byname(pdev, "bd96801-wdg");
+	if (irq > 0) {
+		ret = devm_request_threaded_irq(&pdev->dev, irq, NULL,
+						bd96801_irq_hnd,
+						IRQF_ONESHOT,  "bd96801-wdg",
+						NULL);
+		if (ret)
+			return dev_err_probe(&pdev->dev, ret,
+					     "Failed to register IRQ\n");
+	}
+
+	return devm_watchdog_register_device(&pdev->dev, &w->wdt);
+}
+
+static const struct platform_device_id bd96801_wdt_id[] = {
+	{ "bd96801-wdt", },
+	{ }
+};
+MODULE_DEVICE_TABLE(platform, bd96801_wdt_id);
+
+static struct platform_driver bd96801_wdt = {
+	.driver = {
+		.name = "bd96801-wdt"
+	},
+	.probe = bd96801_wdt_probe,
+	.id_table = bd96801_wdt_id,
+};
+module_platform_driver(bd96801_wdt);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("BD96801 watchdog driver");
+MODULE_LICENSE("GPL");
-- 
2.45.1


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

[PATCH v2 06/10] MAINTAINERS: Add ROHM BD96801 'scalable PMIC' entries

[Matti Vaittinen]

[-- Attachment #1: Type: text/plain, Size: 1510 bytes --]

Add maintainer entries for ROHM BD96801 a.k.a 'scalable PMIC'
drivers to be reviewed by ROHM people.

Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
---
 MAINTAINERS | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index aa3b947fb080..da68144d51ae 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -19111,17 +19111,21 @@ F:	drivers/gpio/gpio-bd71828.c
 F:	drivers/mfd/rohm-bd71828.c
 F:	drivers/mfd/rohm-bd718x7.c
 F:	drivers/mfd/rohm-bd9576.c
+F:	drivers/mfd/rohm-bd96801.c
 F:	drivers/regulator/bd71815-regulator.c
 F:	drivers/regulator/bd71828-regulator.c
 F:	drivers/regulator/bd718x7-regulator.c
 F:	drivers/regulator/bd9576-regulator.c
+F:	drivers/regulator/bd96801-regulator.c
 F:	drivers/regulator/rohm-regulator.c
 F:	drivers/rtc/rtc-bd70528.c
 F:	drivers/watchdog/bd9576_wdt.c
+F:	drivers/watchdog/bd96801_wdt.c
 F:	include/linux/mfd/rohm-bd71815.h
 F:	include/linux/mfd/rohm-bd71828.h
 F:	include/linux/mfd/rohm-bd718x7.h
 F:	include/linux/mfd/rohm-bd957x.h
+F:	include/linux/mfd/rohm-bd96801.h
 F:	include/linux/mfd/rohm-generic.h
 F:	include/linux/mfd/rohm-shared.h
 
-- 
2.45.1


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]