From: Pavel Roskin <proski@gnu.org>
To: Kalle Valo <kalle.valo@iki.fi>
Cc: linux-wireless@vger.kernel.org
Subject: Re: [PATCH 00/12] at76_usb mac80211 port
Date: Mon, 11 Feb 2008 00:05:45 -0500 [thread overview]
Message-ID: <1202706345.20836.26.camel@dv> (raw)
In-Reply-To: <20080210145733.17592.61729.stgit@tikku>
On Sun, 2008-02-10 at 16:59 +0200, Kalle Valo wrote:
> Here's a patch series of my at76_usb mac80211 port. I'm sending them now
> for comments. Currently open mode and WEP authentication are supported.
Kalle, thank you for your work!
I've put your patches on http://git.80211libre.org/at76_usb.git so that
they can be tested by more users. I gave no promise about continuity of
the branch, so I'm ready to replace the patches.
I haven't looked at the code yet, but here are some testing results.
When trying to associate to an AP without security (MadWifi on a PC),
that's what I see in the logs:
wlan3: Initial auth_alg=0
wlan3: authenticate with AP 00:0b:6b:56:01:bf
wlan3: authenticate with AP 00:0b:6b:56:01:bf
wlan3: RX authentication from 00:0b:6b:56:01:bf (alg=0 transaction=2 status=0)
wlan3: authenticated
wlan3: associate with AP 00:0b:6b:56:01:bf
wlan3: authentication frame received from 00:0b:6b:56:01:bf, but not in authenticate state - ignored
wlan3: associate with AP 00:0b:6b:56:01:bf
wlan3: RX AssocResp from 00:0b:6b:56:01:bf (capab=0x421 status=0 aid=1)
wlan3: associated
wlan3: association frame received from 00:0b:6b:56:01:bf, but not in associate state - ignored
No pings come through. I see on the AP that the AP is receiving ARP
requests and sending ARP replies, so it must be the receiving side in
at76_usb that is broken.
When trying to connect to the same AP with a WEP key, this appears in
the kernel log:
phy5: CMD_JOIN failed: 7<7>wlan3: CTS protection enabled
(BSSID=00:0b:6b:56:01:bf)
wlan3: CTS protection disabled (BSSID=00:0b:6b:56:01:bf)
You forgot end of line in the message (that's patch 05/12). I'm totally
at loss why a positive value us printed. When trying to set the key and
ESSID again, I get this:
wlan3: Initial auth_alg=0
wlan3: authenticate with AP 00:0b:6b:56:01:bf
wlan3: authenticate with AP 00:0b:6b:56:01:bf
wlan3: authenticate with AP 00:0b:6b:56:01:bf
wlan3: authentication with AP 00:0b:6b:56:01:bf timed out
Pings don't come through. Everything is within one room. Attenuation
shouldn't be an issue.
Another interesting problem - scan results show the channel two times
(not counting the "frequency" line). Other mac80211 drivers do it once.
No idea why.
wlan3 Scan completed :
Cell 01 - Address: 00:0B:6B:56:01:BF
ESSID:"Moody"
Mode:Master
Frequency:2.462 GHz (Channel 11)
Channel:11
Channel:11
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s
Extra:tsf=00000000159e489e
--
Regards,
Pavel Roskin
next prev parent reply other threads:[~2008-02-11 5:05 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-02-10 14:59 [PATCH 00/12] at76_usb mac80211 port Kalle Valo
2008-02-10 14:59 ` [PATCH 01/12] Use net/mac80211.h instead of net/ieee80211.h Kalle Valo
2008-02-10 15:00 ` [PATCH 02/12] Add at76_dbg_dump() macro Kalle Valo
2008-02-10 15:00 ` [PATCH 03/12] Convert DBG_TX levels to use at76_dbg_dump() Kalle Valo
2008-02-10 15:00 ` [PATCH 04/12] Add DBG_CMD for debugging firmware commands Kalle Valo
2008-02-10 15:00 ` [PATCH 05/12] at76_usb: add mac80211 support Kalle Valo
2008-02-10 15:00 ` [PATCH 06/12] Add support for monitor mode Kalle Valo
2008-02-10 15:49 ` Michael Buesch
2008-02-10 15:52 ` Michael Buesch
2008-03-09 16:10 ` Kalle Valo
2008-03-09 17:39 ` Michael Buesch
2008-02-10 15:00 ` [PATCH 07/12] Add support for WEP Kalle Valo
2008-02-10 15:00 ` [PATCH 08/12] Remove support the legacy stack Kalle Valo
2008-02-10 15:00 ` [PATCH 09/12] Use wiphy_name everywhere where needed Kalle Valo
2008-02-10 15:01 ` [PATCH 10/12] Allocate struct at76_priv using ieee80211_alloc_hw() Kalle Valo
2008-02-10 15:01 ` [PATCH 11/12] Prepare for struct net_device removal Kalle Valo
2008-02-10 15:01 ` [PATCH 12/12] Remove struct net_device Kalle Valo
2008-02-11 5:05 ` Pavel Roskin [this message]
2008-02-11 5:17 ` [PATCH 00/12] at76_usb mac80211 port Pavel Roskin
2008-03-09 16:43 ` Kalle Valo
2008-03-10 1:00 ` Pavel Roskin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1202706345.20836.26.camel@dv \
--to=proski@gnu.org \
--cc=kalle.valo@iki.fi \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).