[PATCH v4 01/03] wl1271: 11n Support, Add Definitions

[Shahar Levi <shahar_levi@ti.com>]

Two acx commands: ht_capabilities & ht_information, 11n sta capabilities macro.

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
---
 drivers/net/wireless/wl12xx/wl1271.h      |   11 ++++-
 drivers/net/wireless/wl12xx/wl1271_acx.h  |   81 +++++++++++++++++++++++++++++
 drivers/net/wireless/wl12xx/wl1271_main.c |   15 +++++
 3 files changed, 106 insertions(+), 1 deletions(-)

diff --git a/drivers/net/wireless/wl12xx/wl1271.h b/drivers/net/wireless/wl12xx/wl1271.h
index 8a4cd76..45a2583 100644
--- a/drivers/net/wireless/wl12xx/wl1271.h
+++ b/drivers/net/wireless/wl12xx/wl1271.h
@@ -432,7 +432,12 @@ struct wl1271 {
 	/* Our association ID */
 	u16 aid;
 
-	/* currently configured rate set */
+	/*
+	 * currently configured rate set:
+	 *	bits  0-15 - 802.11abg rates
+	 *	bits 16-23 - 802.11n   MCS index mask
+	 * support only 1 stream, thus only 8 bits for the MCS rates (0-7).
+	 */
 	u32 sta_rate_set;
 	u32 basic_rate_set;
 	u32 basic_rate;
@@ -509,4 +514,8 @@ int wl1271_plt_stop(struct wl1271 *wl);
 #define WL1271_PRE_POWER_ON_SLEEP 20 /* in miliseconds */
 #define WL1271_POWER_ON_SLEEP 200 /* in miliseconds */
 
+/* Macros to handle wl1271.sta_rate_set */
+#define HW_BG_RATES_MASK	0xffff
+#define HW_HT_RATES_OFFSET	16
+
 #endif
diff --git a/drivers/net/wireless/wl12xx/wl1271_acx.h b/drivers/net/wireless/wl12xx/wl1271_acx.h
index ebb341d..72597a2 100644
--- a/drivers/net/wireless/wl12xx/wl1271_acx.h
+++ b/drivers/net/wireless/wl12xx/wl1271_acx.h
@@ -964,6 +964,87 @@ struct wl1271_acx_rssi_snr_avg_weights {
 	u8 snr_data;
 };
 
+/*
+ * ACX_PEER_HT_CAP
+ * Configure HT capabilities - declare the capabilities of the peer
+ * we are connected to.
+ */
+struct wl1271_acx_ht_capabilities {
+	struct acx_header header;
+
+	/*
+	 * bit 0 - Allow HT Operation
+	 * bit 1 - Allow Greenfield format in TX
+	 * bit 2 - Allow Short GI in TX
+	 * bit 3 - Allow L-SIG TXOP Protection in TX
+	 * bit 4 - Allow HT Control fields in TX.
+	 *         Note, driver will still leave space for HT control in packets
+	 *         regardless of the value of this field. FW will be responsible
+	 *         to drop the HT field from any frame when this Bit set to 0.
+	 * bit 5 - Allow RD initiation in TXOP. FW is allowed to initate RD.
+	 *         Exact policy setting for this feature is TBD.
+	 *         Note, this bit can only be set to 1 if bit 3 is set to 1.
+	 */
+	__le32 ht_capabilites;
+
+	/*
+	 * Indicates to which peer these capabilities apply.
+	 * For infrastructure use ff:ff:ff:ff:ff:ff that indicates relevance
+	 * for all peers.
+	 * Only valid for IBSS/DLS operation.
+	 */
+	u8 mac_address[ETH_ALEN];
+
+	/*
+	 * This the maximum A-MPDU length supported by the AP. The FW may not
+	 * exceed this length when sending A-MPDUs
+	 */
+	u8 ampdu_max_length;
+
+	/* This is the minimal spacing required when sending A-MPDUs to the AP*/
+	u8 ampdu_min_spacing;
+} __packed;
+
+/* HT Capabilites Fw Bit Mask Mapping */
+#define WL1271_ACX_FW_CAP_HT_OPERATION                 BIT(0)
+#define WL1271_ACX_FW_CAP_GREENFIELD_FRAME_FORMAT      BIT(1)
+#define WL1271_ACX_FW_CAP_SHORT_GI_FOR_20MHZ_PACKETS   BIT(2)
+#define WL1271_ACX_FW_CAP_LSIG_TXOP_PROTECTION         BIT(3)
+#define WL1271_ACX_FW_CAP_HT_CONTROL_FIELDS            BIT(4)
+#define WL1271_ACX_FW_CAP_RD_INITIATION                BIT(5)
+
+
+/*
+ * ACX_HT_BSS_OPERATION
+ * Configure HT capabilities - AP rules for behavior in the BSS.
+ */
+struct wl1271_acx_ht_information {
+	struct acx_header header;
+
+	/* Values: 0 - RIFS not allowed, 1 - RIFS allowed */
+	u8 rifs_mode;
+
+	/* Values: 0 - 3 like in spec */
+	u8 ht_protection;
+
+	/* Values: 0 - GF protection not required, 1 - GF protection required */
+	u8 gf_protection;
+
+	/*Values: 0 - TX Burst limit not required, 1 - TX Burst Limit required*/
+	u8 ht_tx_burst_limit;
+
+	/*
+	 * Values: 0 - Dual CTS protection not required,
+	 *         1 - Dual CTS Protection required
+	 * Note: When this value is set to 1 FW will protect all TXOP with RTS
+	 * frame and will not use CTS-to-self regardless of the value of the
+	 * ACX_CTS_PROTECTION information element
+	 */
+	u8 dual_cts_protection;
+
+	u8 padding[3];
+} __packed;
+
 struct wl1271_acx_fw_tsf_information {
 	struct acx_header header;
 
diff --git a/drivers/net/wireless/wl12xx/wl1271_main.c b/drivers/net/wireless/wl12xx/wl1271_main.c
index 48a4b99..a585815 100644
--- a/drivers/net/wireless/wl12xx/wl1271_main.c
+++ b/drivers/net/wireless/wl12xx/wl1271_main.c
@@ -2134,6 +2134,21 @@ static const u8 wl1271_rate_to_idx_2ghz[] = {
 	0                              /* CONF_HW_RXTX_RATE_1    */
 };
 
+/* 11n STA capabilities */
+#define HW_RX_HIGHEST_RATE	72
+
+#define WL1271_HT_CAP { \
+	.cap = IEEE80211_HT_CAP_GRN_FLD | IEEE80211_HT_CAP_SGI_20, \
+	.ht_supported = true, \
+	.ampdu_factor = IEEE80211_HT_MAX_AMPDU_8K, \
+	.ampdu_density = IEEE80211_HT_MPDU_DENSITY_8, \
+	.mcs = { \
+		.rx_mask = { 0xff, 0, 0, 0, 0, 0, 0, 0, 0, 0, }, \
+		.rx_highest = cpu_to_le16(HW_RX_HIGHEST_RATE), \
+		.tx_params = IEEE80211_HT_MCS_TX_DEFINED, \
+		}, \
+}
+
 /* can't be const, mac80211 writes to this */
 static struct ieee80211_supported_band wl1271_band_2ghz = {
 	.channels = wl1271_channels,
-- 
1.6.0.4