From: Vasanthakumar Thiagarajan <vasanth@atheros.com>
To: <linville@tuxdriver.com>
Cc: <linux-wireless@vger.kernel.org>
Subject: [PATCH V2 05/27] ath9k_hw: Initialize tx/rx gain table from initvals.h for AR9485
Date: Thu, 2 Dec 2010 03:06:49 -0800 [thread overview]
Message-ID: <1291288031-3409-6-git-send-email-vasanth@atheros.com> (raw)
In-Reply-To: <1291288031-3409-1-git-send-email-vasanth@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
drivers/net/wireless/ath/ath9k/ar9003_hw.c | 82 +++++++++++++++++++++-------
1 files changed, 62 insertions(+), 20 deletions(-)
diff --git a/drivers/net/wireless/ath/ath9k/ar9003_hw.c b/drivers/net/wireless/ath/ath9k/ar9003_hw.c
index f01c289..21a5bfe 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_hw.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_hw.c
@@ -175,22 +175,52 @@ static void ar9003_tx_gain_table_apply(struct ath_hw *ah)
switch (ar9003_hw_get_tx_gain_idx(ah)) {
case 0:
default:
- INIT_INI_ARRAY(&ah->iniModesTxGain,
- ar9300Modes_lowest_ob_db_tx_gain_table_2p2,
- ARRAY_SIZE(ar9300Modes_lowest_ob_db_tx_gain_table_2p2),
- 5);
+ if (AR_SREV_9485(ah))
+ INIT_INI_ARRAY(&ah->iniModesTxGain,
+ ar9485Modes_lowest_ob_db_tx_gain_1_0,
+ ARRAY_SIZE(ar9485Modes_lowest_ob_db_tx_gain_1_0),
+ 5);
+ else
+ INIT_INI_ARRAY(&ah->iniModesTxGain,
+ ar9300Modes_lowest_ob_db_tx_gain_table_2p2,
+ ARRAY_SIZE(ar9300Modes_lowest_ob_db_tx_gain_table_2p2),
+ 5);
break;
case 1:
- INIT_INI_ARRAY(&ah->iniModesTxGain,
- ar9300Modes_high_ob_db_tx_gain_table_2p2,
- ARRAY_SIZE(ar9300Modes_high_ob_db_tx_gain_table_2p2),
- 5);
+ if (AR_SREV_9485(ah))
+ INIT_INI_ARRAY(&ah->iniModesTxGain,
+ ar9485Modes_high_ob_db_tx_gain_1_0,
+ ARRAY_SIZE(ar9485Modes_lowest_ob_db_tx_gain_1_0),
+ 5);
+ else
+ INIT_INI_ARRAY(&ah->iniModesTxGain,
+ ar9300Modes_high_ob_db_tx_gain_table_2p2,
+ ARRAY_SIZE(ar9300Modes_high_ob_db_tx_gain_table_2p2),
+ 5);
break;
case 2:
- INIT_INI_ARRAY(&ah->iniModesTxGain,
- ar9300Modes_low_ob_db_tx_gain_table_2p2,
- ARRAY_SIZE(ar9300Modes_low_ob_db_tx_gain_table_2p2),
- 5);
+ if (AR_SREV_9485(ah))
+ INIT_INI_ARRAY(&ah->iniModesTxGain,
+ ar9485Modes_low_ob_db_tx_gain_1_0,
+ ARRAY_SIZE(ar9485Modes_lowest_ob_db_tx_gain_1_0),
+ 5);
+ else
+ INIT_INI_ARRAY(&ah->iniModesTxGain,
+ ar9300Modes_low_ob_db_tx_gain_table_2p2,
+ ARRAY_SIZE(ar9300Modes_low_ob_db_tx_gain_table_2p2),
+ 5);
+ break;
+ case 3:
+ if (AR_SREV_9485(ah))
+ INIT_INI_ARRAY(&ah->iniModesTxGain,
+ ar9485Modes_high_power_tx_gain_1_0,
+ ARRAY_SIZE(ar9485Modes_high_power_tx_gain_1_0),
+ 5);
+ else
+ INIT_INI_ARRAY(&ah->iniModesTxGain,
+ ar9300Modes_high_power_tx_gain_table_2p2,
+ ARRAY_SIZE(ar9300Modes_high_power_tx_gain_table_2p2),
+ 5);
break;
}
}
@@ -200,16 +230,28 @@ static void ar9003_rx_gain_table_apply(struct ath_hw *ah)
switch (ar9003_hw_get_rx_gain_idx(ah)) {
case 0:
default:
- INIT_INI_ARRAY(&ah->iniModesRxGain,
- ar9300Common_rx_gain_table_2p2,
- ARRAY_SIZE(ar9300Common_rx_gain_table_2p2),
- 2);
+ if (AR_SREV_9485(ah))
+ INIT_INI_ARRAY(&ah->iniModesRxGain,
+ ar9485Common_rx_gain_1_0,
+ ARRAY_SIZE(ar9485Common_rx_gain_1_0),
+ 2);
+ else
+ INIT_INI_ARRAY(&ah->iniModesRxGain,
+ ar9300Common_rx_gain_table_2p2,
+ ARRAY_SIZE(ar9300Common_rx_gain_table_2p2),
+ 2);
break;
case 1:
- INIT_INI_ARRAY(&ah->iniModesRxGain,
- ar9300Common_wo_xlna_rx_gain_table_2p2,
- ARRAY_SIZE(ar9300Common_wo_xlna_rx_gain_table_2p2),
- 2);
+ if (AR_SREV_9485(ah))
+ INIT_INI_ARRAY(&ah->iniModesRxGain,
+ ar9485Common_wo_xlna_rx_gain_1_0,
+ ARRAY_SIZE(ar9485Common_wo_xlna_rx_gain_1_0),
+ 2);
+ else
+ INIT_INI_ARRAY(&ah->iniModesRxGain,
+ ar9300Common_wo_xlna_rx_gain_table_2p2,
+ ARRAY_SIZE(ar9300Common_wo_xlna_rx_gain_table_2p2),
+ 2);
break;
}
}
--
1.7.0.4
next prev parent reply other threads:[~2010-12-02 11:09 UTC|newest]
Thread overview: 44+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-12-02 11:06 [PATCH V2 00/27] Add support for AR9485 Vasanthakumar Thiagarajan
2010-12-02 11:06 ` [PATCH V2 01/27] ath9k_hw: Define hw version macros " Vasanthakumar Thiagarajan
2010-12-02 11:06 ` [PATCH V2 02/27] ath9k_hw: Add initvals.h " Vasanthakumar Thiagarajan
2010-12-02 11:06 ` [PATCH V2 03/27] ath9k_hw: Enable hw initialization " Vasanthakumar Thiagarajan
2010-12-02 11:06 ` [PATCH V2 04/27] ath9k_hw: Initialize mode registers " Vasanthakumar Thiagarajan
2010-12-02 11:06 ` Vasanthakumar Thiagarajan [this message]
2010-12-02 11:06 ` [PATCH V2 06/27] ath9k_hw: Eeeprom changes " Vasanthakumar Thiagarajan
2010-12-02 11:06 ` [PATCH V2 07/27] ath9k_hw: Disable LDPC " Vasanthakumar Thiagarajan
2010-12-02 11:06 ` [PATCH V2 08/27] ath9k: Disable TX STBC " Vasanthakumar Thiagarajan
2010-12-02 11:06 ` [PATCH V2 09/27] ath9k: Enable extended synch for AR9485 to fix L0s recovery issue Vasanthakumar Thiagarajan
2010-12-02 11:06 ` [PATCH V2 10/27] ath9k_hw: Find the maximum number of chains that hw supports Vasanthakumar Thiagarajan
2010-12-02 11:06 ` [PATCH V2 11/27] ath9k_hw: Configure pll control for AR9485 Vasanthakumar Thiagarajan
2010-12-02 11:06 ` [PATCH V2 12/27] ath9k_hw: Find chansel of AR_PHY_65NM_CH0_SYNTH7 from an array " Vasanthakumar Thiagarajan
2010-12-03 1:45 ` Felix Fietkau
2010-12-03 4:50 ` Vasanthakumar Thiagarajan
2010-12-03 12:14 ` Felix Fietkau
2010-12-03 12:40 ` Vasanthakumar Thiagarajan
2010-12-03 12:48 ` Felix Fietkau
2010-12-06 6:03 ` Vasanthakumar Thiagarajan
2010-12-06 10:42 ` Felix Fietkau
2010-12-06 11:44 ` Vasanthakumar Thiagarajan
2010-12-06 11:50 ` Felix Fietkau
2010-12-06 11:54 ` Vasanthakumar Thiagarajan
2010-12-06 11:51 ` Johannes Berg
2010-12-02 11:06 ` [PATCH V2 13/27] ath9k_hw: Add a helper function to get spur channel pointer from cal data for AR9003 family Vasanthakumar Thiagarajan
2010-12-02 11:06 ` [PATCH V2 14/27] ath9k_hw: Read spur channel information from eeprom for AR9485 Vasanthakumar Thiagarajan
2010-12-02 11:06 ` [PATCH V2 15/27] ath9k_hw: Configure xpa bias level " Vasanthakumar Thiagarajan
2010-12-02 11:07 ` [PATCH V2 16/27] ath9k_hw: Read and configure antenna diversity control " Vasanthakumar Thiagarajan
2010-12-02 11:22 ` Julian Calaby
2010-12-02 12:09 ` Vasanthakumar Thiagarajan
2010-12-02 12:16 ` Julian Calaby
2010-12-02 12:21 ` Vasanthakumar Thiagarajan
2010-12-02 12:29 ` Julian Calaby
2010-12-02 11:07 ` [PATCH V2 17/27] ath9k_hw: Configure attenuation control only for supported chains Vasanthakumar Thiagarajan
2010-12-02 11:07 ` [PATCH V2 18/27] ath9k_hw: Configure internal regulator for AR9485 Vasanthakumar Thiagarajan
2010-12-02 11:07 ` [PATCH V2 19/27] ath9k_hw: Read and configure turnning caps to regulate freq accuracy Vasanthakumar Thiagarajan
2010-12-02 11:07 ` [PATCH V2 20/27] ath9k_hw: Configure power control only for the supported chains Vasanthakumar Thiagarajan
2010-12-02 11:07 ` [PATCH V2 21/27] ath9k_hw: Program appropriate chianmask for AR9485 before starting AGC/IQ cal Vasanthakumar Thiagarajan
2010-12-02 11:07 ` [PATCH V2 22/27] ath9k_hw: Define IQcal correction coefficient registers using index Vasanthakumar Thiagarajan
2010-12-02 11:07 ` [PATCH V2 23/27] ath9k_hw: Add IQ cal changes for AR9485 Vasanthakumar Thiagarajan
2010-12-02 11:07 ` [PATCH V2 24/27] ath9k_hw: Program appropriate register for temperature compensation cal " Vasanthakumar Thiagarajan
2010-12-02 11:07 ` [PATCH V2 25/27] ath9k_hw: Setup paprd only for supported chains Vasanthakumar Thiagarajan
2010-12-02 11:07 ` [PATCH V2 26/27] ath9k_hw: Disable MRC CCK for AR9485 Vasanthakumar Thiagarajan
2010-12-02 11:07 ` [PATCH V2 27/27] ath9k: Add device id of AR9485 to pci table Vasanthakumar Thiagarajan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1291288031-3409-6-git-send-email-vasanth@atheros.com \
--to=vasanth@atheros.com \
--cc=linux-wireless@vger.kernel.org \
--cc=linville@tuxdriver.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).