linux-wireless.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Felix Fietkau <nbd@openwrt.org>
To: linux-wireless@vger.kernel.org
Cc: linville@tuxdriver.com, lrodriguez@atheros.com,
	vasanth@atheros.com, mark@moxienet.com
Subject: [PATCH v2 4/4] ath9k: improve reliability of beacon transmission and stuck beacon handling
Date: Thu, 10 Mar 2011 14:41:39 +0100	[thread overview]
Message-ID: <1299764499-76251-4-git-send-email-nbd@openwrt.org> (raw)
In-Reply-To: <1299764499-76251-3-git-send-email-nbd@openwrt.org>

ath9k calls ath9k_hw_stoptxdma every time it sends a beacon, however there
is not much point in doing that if the previous beacon and mcast traffic
went out properly. On AR9380, calling that function too often can result
in an increase of stuck beacons due to differences in the handling of the
queue enable/disable functionality.

With this patch, the queue will only be explicitly stopped if the previous
data frames were not sent successfully. With the beacon code being the
only remaining user of ath9k_hw_stoptxdma, this function can be simplified
in order to remove the now pointless attempts at waiting for transmission
completion, which would never happen at this point due to the different
method of tx scheduling of the beacon queue.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
---
 drivers/net/wireless/ath/ath9k/beacon.c |   13 +-----
 drivers/net/wireless/ath/ath9k/mac.c    |   68 +++---------------------------
 drivers/net/wireless/ath/ath9k/mac.h    |    2 +-
 3 files changed, 10 insertions(+), 73 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/beacon.c b/drivers/net/wireless/ath/ath9k/beacon.c
index a4bdfdb..6d2a545f 100644
--- a/drivers/net/wireless/ath/ath9k/beacon.c
+++ b/drivers/net/wireless/ath/ath9k/beacon.c
@@ -373,6 +373,7 @@ void ath_beacon_tasklet(unsigned long data)
 			ath_dbg(common, ATH_DBG_BSTUCK,
 				"missed %u consecutive beacons\n",
 				sc->beacon.bmisscnt);
+			ath9k_hw_stop_dma_queue(ah, sc->beacon.beaconq);
 			ath9k_hw_bstuck_nfcal(ah);
 		} else if (sc->beacon.bmisscnt >= BSTUCK_THRESH) {
 			ath_dbg(common, ATH_DBG_BSTUCK,
@@ -450,16 +451,6 @@ void ath_beacon_tasklet(unsigned long data)
 		sc->beacon.updateslot = OK;
 	}
 	if (bfaddr != 0) {
-		/*
-		 * Stop any current dma and put the new frame(s) on the queue.
-		 * This should never fail since we check above that no frames
-		 * are still pending on the queue.
-		 */
-		if (!ath9k_hw_stoptxdma(ah, sc->beacon.beaconq)) {
-			ath_err(common, "beacon queue %u did not stop?\n",
-				sc->beacon.beaconq);
-		}
-
 		/* NB: cabq traffic should already be queued and primed */
 		ath9k_hw_puttxbuf(ah, sc->beacon.beaconq, bfaddr);
 		ath9k_hw_txstart(ah, sc->beacon.beaconq);
@@ -780,7 +771,7 @@ void ath9k_set_beaconing_status(struct ath_softc *sc, bool status)
 		ah->imask &= ~ATH9K_INT_SWBA;
 		ath9k_hw_set_interrupts(ah, ah->imask);
 		tasklet_kill(&sc->bcon_tasklet);
-		ath9k_hw_stoptxdma(ah, sc->beacon.beaconq);
+		ath9k_hw_stop_dma_queue(ah, sc->beacon.beaconq);
 	}
 	ath9k_ps_restore(sc);
 }
diff --git a/drivers/net/wireless/ath/ath9k/mac.c b/drivers/net/wireless/ath/ath9k/mac.c
index 188af17..0a734f1 100644
--- a/drivers/net/wireless/ath/ath9k/mac.c
+++ b/drivers/net/wireless/ath/ath9k/mac.c
@@ -170,84 +170,30 @@ void ath9k_hw_abort_tx_dma(struct ath_hw *ah)
 }
 EXPORT_SYMBOL(ath9k_hw_abort_tx_dma);
 
-bool ath9k_hw_stoptxdma(struct ath_hw *ah, u32 q)
+bool ath9k_hw_stop_dma_queue(struct ath_hw *ah, u32 q)
 {
-#define ATH9K_TX_STOP_DMA_TIMEOUT	4000    /* usec */
+#define ATH9K_TX_STOP_DMA_TIMEOUT	1000    /* usec */
 #define ATH9K_TIME_QUANTUM		100     /* usec */
-	struct ath_common *common = ath9k_hw_common(ah);
-	struct ath9k_hw_capabilities *pCap = &ah->caps;
-	struct ath9k_tx_queue_info *qi;
-	u32 tsfLow, j, wait;
-	u32 wait_time = ATH9K_TX_STOP_DMA_TIMEOUT / ATH9K_TIME_QUANTUM;
-
-	if (q >= pCap->total_queues) {
-		ath_dbg(common, ATH_DBG_QUEUE,
-			"Stopping TX DMA, invalid queue: %u\n", q);
-		return false;
-	}
-
-	qi = &ah->txq[q];
-	if (qi->tqi_type == ATH9K_TX_QUEUE_INACTIVE) {
-		ath_dbg(common, ATH_DBG_QUEUE,
-			"Stopping TX DMA, inactive queue: %u\n", q);
-		return false;
-	}
+	int wait_time = ATH9K_TX_STOP_DMA_TIMEOUT / ATH9K_TIME_QUANTUM;
+	int wait;
 
 	REG_WRITE(ah, AR_Q_TXD, 1 << q);
 
 	for (wait = wait_time; wait != 0; wait--) {
 		if (ath9k_hw_numtxpending(ah, q) == 0)
 			break;
-		udelay(ATH9K_TIME_QUANTUM);
-	}
-
-	if (ath9k_hw_numtxpending(ah, q)) {
-		ath_dbg(common, ATH_DBG_QUEUE,
-			"%s: Num of pending TX Frames %d on Q %d\n",
-			__func__, ath9k_hw_numtxpending(ah, q), q);
-
-		for (j = 0; j < 2; j++) {
-			tsfLow = REG_READ(ah, AR_TSF_L32);
-			REG_WRITE(ah, AR_QUIET2,
-				  SM(10, AR_QUIET2_QUIET_DUR));
-			REG_WRITE(ah, AR_QUIET_PERIOD, 100);
-			REG_WRITE(ah, AR_NEXT_QUIET_TIMER, tsfLow >> 10);
-			REG_SET_BIT(ah, AR_TIMER_MODE,
-				       AR_QUIET_TIMER_EN);
-
-			if ((REG_READ(ah, AR_TSF_L32) >> 10) == (tsfLow >> 10))
-				break;
-
-			ath_dbg(common, ATH_DBG_QUEUE,
-				"TSF has moved while trying to set quiet time TSF: 0x%08x\n",
-				tsfLow);
-		}
-
-		REG_SET_BIT(ah, AR_DIAG_SW, AR_DIAG_FORCE_CH_IDLE_HIGH);
 
-		udelay(200);
-		REG_CLR_BIT(ah, AR_TIMER_MODE, AR_QUIET_TIMER_EN);
-
-		wait = wait_time;
-		while (ath9k_hw_numtxpending(ah, q)) {
-			if ((--wait) == 0) {
-				ath_err(common,
-					"Failed to stop TX DMA in 100 msec after killing last frame\n");
-				break;
-			}
-			udelay(ATH9K_TIME_QUANTUM);
-		}
-
-		REG_CLR_BIT(ah, AR_DIAG_SW, AR_DIAG_FORCE_CH_IDLE_HIGH);
+		udelay(ATH9K_TIME_QUANTUM);
 	}
 
 	REG_WRITE(ah, AR_Q_TXD, 0);
+
 	return wait != 0;
 
 #undef ATH9K_TX_STOP_DMA_TIMEOUT
 #undef ATH9K_TIME_QUANTUM
 }
-EXPORT_SYMBOL(ath9k_hw_stoptxdma);
+EXPORT_SYMBOL(ath9k_hw_stop_dma_queue);
 
 void ath9k_hw_gettxintrtxqs(struct ath_hw *ah, u32 *txqs)
 {
diff --git a/drivers/net/wireless/ath/ath9k/mac.h b/drivers/net/wireless/ath/ath9k/mac.h
index d37c6d4..b2b2ff8 100644
--- a/drivers/net/wireless/ath/ath9k/mac.h
+++ b/drivers/net/wireless/ath/ath9k/mac.h
@@ -676,7 +676,7 @@ void ath9k_hw_txstart(struct ath_hw *ah, u32 q);
 void ath9k_hw_cleartxdesc(struct ath_hw *ah, void *ds);
 u32 ath9k_hw_numtxpending(struct ath_hw *ah, u32 q);
 bool ath9k_hw_updatetxtriglevel(struct ath_hw *ah, bool bIncTrigLevel);
-bool ath9k_hw_stoptxdma(struct ath_hw *ah, u32 q);
+bool ath9k_hw_stop_dma_queue(struct ath_hw *ah, u32 q);
 void ath9k_hw_abort_tx_dma(struct ath_hw *ah);
 void ath9k_hw_gettxintrtxqs(struct ath_hw *ah, u32 *txqs);
 bool ath9k_hw_set_txq_props(struct ath_hw *ah, int q,
-- 
1.7.3.2


  reply	other threads:[~2011-03-10 13:41 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2011-03-10 13:41 [PATCH v2 1/4] ath9k_hw: fix REG_SET_BIT and REG_CLR_BIT for multiple bits Felix Fietkau
2011-03-10 13:41 ` [PATCH v2 2/4] ath9k: fix stopping tx dma on reset Felix Fietkau
2011-03-10 13:41   ` [PATCH v2 3/4] ath9k: fix the .flush driver op implementation Felix Fietkau
2011-03-10 13:41     ` Felix Fietkau [this message]
2011-03-10 21:55       ` [PATCH v2 4/4] ath9k: improve reliability of beacon transmission and stuck beacon handling Mark Mentovai
2011-03-10 22:13         ` Felix Fietkau
2011-03-10 22:36           ` Mark Mentovai
2011-03-10 21:55     ` [PATCH v2 3/4] ath9k: fix the .flush driver op implementation Mark Mentovai
2011-03-10 22:18       ` Felix Fietkau

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1299764499-76251-4-git-send-email-nbd@openwrt.org \
    --to=nbd@openwrt.org \
    --cc=linux-wireless@vger.kernel.org \
    --cc=linville@tuxdriver.com \
    --cc=lrodriguez@atheros.com \
    --cc=mark@moxienet.com \
    --cc=vasanth@atheros.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).