From: Vasanthakumar Thiagarajan <vasanth@atheros.com>
To: <linville@tuxdriver.com>
Cc: <linux-wireless@vger.kernel.org>
Subject: [PATCH 00/22] Add support for AR9340
Date: Tue, 12 Apr 2011 18:27:00 +0530 [thread overview]
Message-ID: <1302613042-1754-1-git-send-email-vasanth@atheros.com> (raw)
John,
This patch set mainly adds support for AR9340 which is a built in
wireless mac in ar934x SOCs. It is 2x2, 2.4Ghz only in ar9341 SOC and
dual band in ar9342/ar9344 SOCs.
Vasanth
Vasanthakumar Thiagarajan (22):
ath9k_hw: Define devid and mac version for AR9340
ath9k_hw: Take care of few host interface register changes for AR9340
ath9k_hw: Introduce a bool for 25mhz clock and populate it
ath9k_hw: Configure pll control register accordingly for AR9340
ath9k_hw: Add initvals.h for ar9340
ath9k_hw: Initialize mode registers from initvals.h for AR9340
ath9k_hw: Don't do ani initialization for AR9340
ath9k_hw: Initialize tx and rx gain table from initvals.h for ar9340
ath9k_hw: Read spur frequency information from eeprom for AR9340
ath9k_hw: Configure RF channel freqency for AR9340
ath9k_hw: Clean up rx/tx chain configuration before AGC/IQ cal
ath9k_hw: Fix register offset AR_PHY_65NM_CH0_THERM for AR9340
ath9k_hw: Don't configure AR_CH0_THERM for AR9340
ath9k_hw: Skip internal regulator configuration for AR9340
ath9k_hw: Configure tuning capacitance value for AR9340 as well
ath9k_hw: Enable byte Tx/Rx data swap for AR9340
ath9k_hw: Configure chain switch table and attenuation control only
for active chains
ath9k_hw: Read iq calibration data only for active chains
ath9k: Add AR9340 platform id to id table
ath9k_hw: Assign macversion based on devid for built-in wmac
ath9k_hw: Disable INTR_HOST1_FATAL to avoid interrupt strom with
ar9430
ath9k_hw: Enable AR9340 support
drivers/net/wireless/ath/ath9k/ahb.c | 4 +
drivers/net/wireless/ath/ath9k/ar9003_calib.c | 37 +-
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c | 59 +-
drivers/net/wireless/ath/ath9k/ar9003_hw.c | 101 ++-
drivers/net/wireless/ath/ath9k/ar9003_phy.c | 30 +-
drivers/net/wireless/ath/ath9k/ar9003_phy.h | 2 +-
drivers/net/wireless/ath/ath9k/ar9340_initvals.h | 1525 ++++++++++++++++++++++
drivers/net/wireless/ath/ath9k/hw.c | 93 ++-
drivers/net/wireless/ath/ath9k/hw.h | 6 +-
drivers/net/wireless/ath/ath9k/mac.c | 10 +-
drivers/net/wireless/ath/ath9k/phy.h | 3 +
drivers/net/wireless/ath/ath9k/reg.h | 81 +-
12 files changed, 1850 insertions(+), 101 deletions(-)
create mode 100644 drivers/net/wireless/ath/ath9k/ar9340_initvals.h
next reply other threads:[~2011-04-12 12:57 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-04-12 12:57 Vasanthakumar Thiagarajan [this message]
2011-04-12 12:57 ` [PATCH 01/22] ath9k_hw: Define devid and mac version for AR9340 Vasanthakumar Thiagarajan
2011-04-12 12:57 ` [PATCH 02/22] ath9k_hw: Take care of few host interface register changes " Vasanthakumar Thiagarajan
2011-04-13 11:05 ` Kalle Valo
2011-04-19 5:56 ` Vasanthakumar Thiagarajan
2011-04-12 12:57 ` [PATCH 05/22] ath9k_hw: Add initvals.h for ar9340 Vasanthakumar Thiagarajan
2011-04-12 12:57 ` [PATCH 08/22] ath9k_hw: Initialize tx and rx gain table from " Vasanthakumar Thiagarajan
2011-04-12 12:57 ` [PATCH 12/22] ath9k_hw: Fix register offset AR_PHY_65NM_CH0_THERM for AR9340 Vasanthakumar Thiagarajan
2011-04-12 12:57 ` [PATCH 13/22] ath9k_hw: Don't configure AR_CH0_THERM " Vasanthakumar Thiagarajan
2011-04-12 12:57 ` [PATCH 16/22] ath9k_hw: Enable byte Tx/Rx data swap " Vasanthakumar Thiagarajan
2011-04-12 12:57 ` [PATCH 19/22] ath9k: Add AR9340 platform id to id table Vasanthakumar Thiagarajan
2011-04-12 12:57 ` [PATCH 20/22] ath9k_hw: Assign macversion based on devid for built-in wmac Vasanthakumar Thiagarajan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1302613042-1754-1-git-send-email-vasanth@atheros.com \
--to=vasanth@atheros.com \
--cc=linux-wireless@vger.kernel.org \
--cc=linville@tuxdriver.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).