From: Felix Fietkau <nbd@openwrt.org>
To: linux-wireless@vger.kernel.org
Cc: linville@tuxdriver.com, mcgrof@qca.qualcomm.com
Subject: [PATCH 2/2] ath9k: always set common->macaddr to the MAC adress of a virtual interface
Date: Tue, 16 Apr 2013 12:51:57 +0200 [thread overview]
Message-ID: <1366109517-64645-2-git-send-email-nbd@openwrt.org> (raw)
In-Reply-To: <1366109517-64645-1-git-send-email-nbd@openwrt.org>
In some cases it can be useful to change the MAC address of a virtual
interface to something that's completely different from the EEPROM
stored MAC address. In this case it is a bad idea to use the EEPROM MAC
address for calculating the BSSID mask, as that would make it too wide.
In one case a few devices have been observed to send ACKs for many
packets on the channel not directed at them, which results in a neat
Denial of Service attack on the channel.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
---
drivers/net/wireless/ath/ath9k/ath9k.h | 7 +++----
drivers/net/wireless/ath/ath9k/main.c | 9 +++++++--
2 files changed, 10 insertions(+), 6 deletions(-)
diff --git a/drivers/net/wireless/ath/ath9k/ath9k.h b/drivers/net/wireless/ath/ath9k/ath9k.h
index 86d3572..1915f12 100644
--- a/drivers/net/wireless/ath/ath9k/ath9k.h
+++ b/drivers/net/wireless/ath/ath9k/ath9k.h
@@ -658,11 +658,10 @@ enum sc_op_flags {
struct ath_rate_table;
struct ath9k_vif_iter_data {
- const u8 *hw_macaddr; /* phy's hardware address, set
- * before starting iteration for
- * valid bssid mask.
- */
+ u8 hw_macaddr[ETH_ALEN]; /* address of the first vif */
u8 mask[ETH_ALEN]; /* bssid mask */
+ bool has_hw_macaddr;
+
int naps; /* number of AP vifs */
int nmeshes; /* number of mesh vifs */
int nstations; /* number of station vifs */
diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c
index a383483..6963862 100644
--- a/drivers/net/wireless/ath/ath9k/main.c
+++ b/drivers/net/wireless/ath/ath9k/main.c
@@ -839,10 +839,14 @@ static void ath9k_vif_iter(void *data, u8 *mac, struct ieee80211_vif *vif)
struct ath9k_vif_iter_data *iter_data = data;
int i;
- if (iter_data->hw_macaddr)
+ if (iter_data->has_hw_macaddr) {
for (i = 0; i < ETH_ALEN; i++)
iter_data->mask[i] &=
~(iter_data->hw_macaddr[i] ^ mac[i]);
+ } else {
+ memcpy(iter_data->hw_macaddr, mac, ETH_ALEN);
+ iter_data->has_hw_macaddr = true;
+ }
switch (vif->type) {
case NL80211_IFTYPE_AP:
@@ -891,7 +895,6 @@ void ath9k_calculate_iter_data(struct ieee80211_hw *hw,
* together with the BSSID mask when matching addresses.
*/
memset(iter_data, 0, sizeof(*iter_data));
- iter_data->hw_macaddr = common->macaddr;
memset(&iter_data->mask, 0xff, ETH_ALEN);
if (vif)
@@ -901,6 +904,8 @@ void ath9k_calculate_iter_data(struct ieee80211_hw *hw,
ieee80211_iterate_active_interfaces_atomic(
sc->hw, IEEE80211_IFACE_ITER_RESUME_ALL,
ath9k_vif_iter, iter_data);
+
+ memcpy(common->macaddr, iter_data->hw_macaddr, ETH_ALEN);
}
/* Called with sc->mutex held. */
--
1.8.0.2
next prev parent reply other threads:[~2013-04-16 10:52 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-04-16 10:51 [PATCH 1/2] ath: update hardware mac address with bssid mask Felix Fietkau
2013-04-16 10:51 ` Felix Fietkau [this message]
2013-04-17 16:39 ` [PATCH 2/2] ath9k: always set common->macaddr to the MAC adress of a virtual interface Simon Wunderlich
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1366109517-64645-2-git-send-email-nbd@openwrt.org \
--to=nbd@openwrt.org \
--cc=linux-wireless@vger.kernel.org \
--cc=linville@tuxdriver.com \
--cc=mcgrof@qca.qualcomm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox