From: Peter Wu <lekensteyn@gmail.com>
To: Larry Finger <Larry.Finger@lwfinger.net>,
Chaoming_Li <chaoming_li@realsil.com.cn>
Cc: linux-wireless@vger.kernel.org, linux-kernel@vger.kernel.org,
lekensteyn@gmail.com
Subject: [PATCH 2/3] rtlwifi: properly apply filter flags
Date: Fri, 14 Feb 2014 19:03:45 +0100 [thread overview]
Message-ID: <1392401026-18417-3-git-send-email-lekensteyn@gmail.com> (raw)
In-Reply-To: <1392401026-18417-1-git-send-email-lekensteyn@gmail.com>
commit 0baa0fd76f3f5a134461d6cf30294f6bb1bb824c
("rtlwifi: Convert core routines for addition of rtl8192se and
rtl8192de") removed setting HW_VAR_RCR, HW_VAR_MGT_FILTER and
HW_VAR_CTRL_FILTER. The last two are probably done because some hardware
does not support them. The first is probably a mistake. This patch adds
the missing set_hw_reg call.
For PCI support, rx_conf is not touched directly. Instead, get_hw_reg is
used to abstract between receive_config (for PCI) and rx_conf (for USB).
This was tested on a 10ec:8176 Realtek RTL8188CE (according to the
label on the mini-PCIe card). Before this patch, `iw wlan0 set monitor
otherbss` did not capture frames from other BSS's. After this patch, it
does print packets.
Tested-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
---
drivers/net/wireless/rtlwifi/core.c | 52 +++++++++++++++++++++----------------
1 file changed, 30 insertions(+), 22 deletions(-)
diff --git a/drivers/net/wireless/rtlwifi/core.c b/drivers/net/wireless/rtlwifi/core.c
index 2d337a0..6df4df0 100644
--- a/drivers/net/wireless/rtlwifi/core.c
+++ b/drivers/net/wireless/rtlwifi/core.c
@@ -475,20 +475,40 @@ static void rtl_op_configure_filter(struct ieee80211_hw *hw,
{
struct rtl_priv *rtlpriv = rtl_priv(hw);
struct rtl_mac *mac = rtl_mac(rtl_priv(hw));
+ u32 rx_conf;
*new_flags &= RTL_SUPPORTED_FILTERS;
if (!changed_flags)
return;
+ /* if ssid not set to hw don't check bssid
+ * here just used for linked scanning, & linked
+ * and nolink check bssid is set in set network_type */
+ if ((changed_flags & FIF_BCN_PRBRESP_PROMISC) &&
+ (mac->link_state >= MAC80211_LINKED)) {
+ if (mac->opmode != NL80211_IFTYPE_AP &&
+ mac->opmode != NL80211_IFTYPE_MESH_POINT) {
+ if (*new_flags & FIF_BCN_PRBRESP_PROMISC) {
+ rtlpriv->cfg->ops->set_chk_bssid(hw, false);
+ } else {
+ rtlpriv->cfg->ops->set_chk_bssid(hw, true);
+ }
+ }
+ }
+
+ /* must be called after set_chk_bssid since that function modifies the
+ * RCR register too. */
+ rtlpriv->cfg->ops->get_hw_reg(hw, HW_VAR_RCR, (u8 *)(&rx_conf));
+
/*TODO: we disable broadcase now, so enable here */
if (changed_flags & FIF_ALLMULTI) {
if (*new_flags & FIF_ALLMULTI) {
- mac->rx_conf |= rtlpriv->cfg->maps[MAC_RCR_AM] |
+ rx_conf |= rtlpriv->cfg->maps[MAC_RCR_AM] |
rtlpriv->cfg->maps[MAC_RCR_AB];
RT_TRACE(rtlpriv, COMP_MAC80211, DBG_LOUD,
"Enable receive multicast frame\n");
} else {
- mac->rx_conf &= ~(rtlpriv->cfg->maps[MAC_RCR_AM] |
+ rx_conf &= ~(rtlpriv->cfg->maps[MAC_RCR_AM] |
rtlpriv->cfg->maps[MAC_RCR_AB]);
RT_TRACE(rtlpriv, COMP_MAC80211, DBG_LOUD,
"Disable receive multicast frame\n");
@@ -497,39 +517,25 @@ static void rtl_op_configure_filter(struct ieee80211_hw *hw,
if (changed_flags & FIF_FCSFAIL) {
if (*new_flags & FIF_FCSFAIL) {
- mac->rx_conf |= rtlpriv->cfg->maps[MAC_RCR_ACRC32];
+ rx_conf |= rtlpriv->cfg->maps[MAC_RCR_ACRC32];
RT_TRACE(rtlpriv, COMP_MAC80211, DBG_LOUD,
"Enable receive FCS error frame\n");
} else {
- mac->rx_conf &= ~rtlpriv->cfg->maps[MAC_RCR_ACRC32];
+ rx_conf &= ~rtlpriv->cfg->maps[MAC_RCR_ACRC32];
RT_TRACE(rtlpriv, COMP_MAC80211, DBG_LOUD,
"Disable receive FCS error frame\n");
}
}
- /* if ssid not set to hw don't check bssid
- * here just used for linked scanning, & linked
- * and nolink check bssid is set in set network_type */
- if ((changed_flags & FIF_BCN_PRBRESP_PROMISC) &&
- (mac->link_state >= MAC80211_LINKED)) {
- if (mac->opmode != NL80211_IFTYPE_AP &&
- mac->opmode != NL80211_IFTYPE_MESH_POINT) {
- if (*new_flags & FIF_BCN_PRBRESP_PROMISC) {
- rtlpriv->cfg->ops->set_chk_bssid(hw, false);
- } else {
- rtlpriv->cfg->ops->set_chk_bssid(hw, true);
- }
- }
- }
if (changed_flags & FIF_CONTROL) {
if (*new_flags & FIF_CONTROL) {
- mac->rx_conf |= rtlpriv->cfg->maps[MAC_RCR_ACF];
+ rx_conf |= rtlpriv->cfg->maps[MAC_RCR_ACF];
RT_TRACE(rtlpriv, COMP_MAC80211, DBG_LOUD,
"Enable receive control frame\n");
} else {
- mac->rx_conf &= ~rtlpriv->cfg->maps[MAC_RCR_ACF];
+ rx_conf &= ~rtlpriv->cfg->maps[MAC_RCR_ACF];
RT_TRACE(rtlpriv, COMP_MAC80211, DBG_LOUD,
"Disable receive control frame\n");
}
@@ -537,15 +543,17 @@ static void rtl_op_configure_filter(struct ieee80211_hw *hw,
if (changed_flags & FIF_OTHER_BSS) {
if (*new_flags & FIF_OTHER_BSS) {
- mac->rx_conf |= rtlpriv->cfg->maps[MAC_RCR_AAP];
+ rx_conf |= rtlpriv->cfg->maps[MAC_RCR_AAP];
RT_TRACE(rtlpriv, COMP_MAC80211, DBG_LOUD,
"Enable receive other BSS's frame\n");
} else {
- mac->rx_conf &= ~rtlpriv->cfg->maps[MAC_RCR_AAP];
+ rx_conf &= ~rtlpriv->cfg->maps[MAC_RCR_AAP];
RT_TRACE(rtlpriv, COMP_MAC80211, DBG_LOUD,
"Disable receive other BSS's frame\n");
}
}
+
+ rtlpriv->cfg->ops->set_hw_reg(hw, HW_VAR_RCR, (u8 *)(&rx_conf));
}
static int rtl_op_sta_add(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
--
1.8.5.4
next prev parent reply other threads:[~2014-02-14 18:03 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-02-14 18:03 [PATCH 0/3] rtlwifi promiscious mode fix and cleanup Peter Wu
2014-02-14 18:03 ` [PATCH 1/3] rtlwifi: avoid accessing RCR directly Peter Wu
2014-02-14 21:28 ` Larry Finger
2014-02-14 21:46 ` Peter Wu
2014-02-14 18:03 ` Peter Wu [this message]
2014-02-14 21:32 ` [PATCH 2/3] rtlwifi: properly apply filter flags Larry Finger
2014-02-14 18:03 ` [PATCH 3/3] rtlwifi: remove unused allow_all_destaddr functions Peter Wu
2014-02-14 21:38 ` Larry Finger
2014-02-14 21:48 ` Peter Wu
2014-02-14 21:57 ` Larry Finger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1392401026-18417-3-git-send-email-lekensteyn@gmail.com \
--to=lekensteyn@gmail.com \
--cc=Larry.Finger@lwfinger.net \
--cc=chaoming_li@realsil.com.cn \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).