From: Erik Stromdahl <erik.stromdahl@gmail.com>
To: kvalo@qca.qualcomm.com, linux-wireless@vger.kernel.org,
ath10k@lists.infradead.org
Cc: Erik Stromdahl <erik.stromdahl@gmail.com>
Subject: [RFC 07/10] ath10k: per target configurablity of various items
Date: Fri, 13 Jan 2017 22:35:06 +0100 [thread overview]
Message-ID: <1484343309-6327-8-git-send-email-erik.stromdahl@gmail.com> (raw)
In-Reply-To: <1484343309-6327-1-git-send-email-erik.stromdahl@gmail.com>
Added ability to set bus type and configure the max number of
peers in the ath10k_hw_params struct.
With this functionality it is possible to have a different
hw configuration depending on bus type for the same radio
chipset.
E.g. SDIO and USB devices using the same chipset as PCIe
devices will potentially use different board files and perhaps
other configuration parameters.
One such parameter is the max number of peers.
Instead of using a default value (suitable for PCIe devices)
derived from the WMI op version, a per target value can be
used instead.
This is needed by the QCA9377 USB device in order to prevent
the target fw to crash after HTT RX ring cfg is issued.
Apparently, the QCA9377 HL device does not seem to handle the
same amount of peers as the LL devices.
A new struct ath10k_hw_params item for QCA9377 USB devices was
also added to ath10k_hw_params_list.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
---
drivers/net/wireless/ath/ath10k/core.c | 55 ++++++++++++++++++++++++++-----
drivers/net/wireless/ath/ath10k/core.h | 7 ----
drivers/net/wireless/ath/ath10k/hw.h | 23 +++++++++++++
drivers/net/wireless/ath/ath10k/wmi-tlv.c | 4 +--
4 files changed, 72 insertions(+), 17 deletions(-)
diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index 573e772..31a9471 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -282,6 +282,28 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = {
.decap_align_bytes = 4,
},
{
+ .id = QCA9377_HW_1_1_DEV_VERSION,
+ .dev_id = QCA9377_1_0_DEVICE_ID,
+ .name = "qca9377 hw1.1 usb",
+ .patch_load_addr = QCA9377_HW_1_0_PATCH_LOAD_ADDR,
+ .uart_pin = 6,
+ .otp_exe_param = 0,
+ .channel_counters_freq_hz = 88000,
+ .max_probe_resp_desc_thres = 0,
+ .cal_data_len = 8124,
+ .fw = {
+ .dir = QCA9377_HW_1_0_FW_DIR,
+ .board = QCA9377_HW_1_0_BOARD_DATA_FILE_USB,
+ .board_size = QCA9377_BOARD_DATA_SZ,
+ .board_ext_size = QCA9377_BOARD_EXT_DATA_SZ,
+ },
+ .hw_ops = &qca988x_ops,
+ .decap_align_bytes = 4,
+ .max_num_peers = TARGET_QCA9377_HL_NUM_PEERS,
+ .is_high_latency = true,
+ .bus = ATH10K_BUS_USB,
+ },
+ {
.id = QCA4019_HW_1_0_DEV_VERSION,
.dev_id = 0,
.name = "qca4019 hw1.0",
@@ -1487,9 +1509,19 @@ static int ath10k_init_hw_params(struct ath10k *ar)
for (i = 0; i < ARRAY_SIZE(ath10k_hw_params_list); i++) {
hw_params = &ath10k_hw_params_list[i];
- if (hw_params->id == ar->target_version &&
- hw_params->dev_id == ar->dev_id)
- break;
+ if (ar->is_high_latency) {
+ /* High latency devices will use different fw depending
+ * on if it is a USB or SDIO device.
+ */
+ if (hw_params->bus == ar->hif.bus &&
+ hw_params->id == ar->target_version &&
+ hw_params->dev_id == ar->dev_id)
+ break;
+ } else {
+ if (hw_params->id == ar->target_version &&
+ hw_params->dev_id == ar->dev_id)
+ break;
+ }
}
if (i == ARRAY_SIZE(ath10k_hw_params_list)) {
@@ -1580,6 +1612,7 @@ static void ath10k_core_set_coverage_class_work(struct work_struct *work)
static int ath10k_core_init_firmware_features(struct ath10k *ar)
{
struct ath10k_fw_file *fw_file = &ar->normal_mode_fw.fw_file;
+ int max_num_peers;
if (test_bit(ATH10K_FW_FEATURE_WMI_10_2, fw_file->fw_features) &&
!test_bit(ATH10K_FW_FEATURE_WMI_10X, fw_file->fw_features)) {
@@ -1664,7 +1697,7 @@ static int ath10k_core_init_firmware_features(struct ath10k *ar)
switch (fw_file->wmi_op_version) {
case ATH10K_FW_WMI_OP_VERSION_MAIN:
- ar->max_num_peers = TARGET_NUM_PEERS;
+ max_num_peers = TARGET_NUM_PEERS;
ar->max_num_stations = TARGET_NUM_STATIONS;
ar->max_num_vdevs = TARGET_NUM_VDEVS;
ar->htt.max_num_pending_tx = TARGET_NUM_MSDU_DESC;
@@ -1676,10 +1709,10 @@ static int ath10k_core_init_firmware_features(struct ath10k *ar)
case ATH10K_FW_WMI_OP_VERSION_10_2:
case ATH10K_FW_WMI_OP_VERSION_10_2_4:
if (ath10k_peer_stats_enabled(ar)) {
- ar->max_num_peers = TARGET_10X_TX_STATS_NUM_PEERS;
+ max_num_peers = TARGET_10X_TX_STATS_NUM_PEERS;
ar->max_num_stations = TARGET_10X_TX_STATS_NUM_STATIONS;
} else {
- ar->max_num_peers = TARGET_10X_NUM_PEERS;
+ max_num_peers = TARGET_10X_NUM_PEERS;
ar->max_num_stations = TARGET_10X_NUM_STATIONS;
}
ar->max_num_vdevs = TARGET_10X_NUM_VDEVS;
@@ -1688,7 +1721,7 @@ static int ath10k_core_init_firmware_features(struct ath10k *ar)
ar->max_spatial_stream = WMI_MAX_SPATIAL_STREAM;
break;
case ATH10K_FW_WMI_OP_VERSION_TLV:
- ar->max_num_peers = TARGET_TLV_NUM_PEERS;
+ max_num_peers = TARGET_TLV_NUM_PEERS;
ar->max_num_stations = TARGET_TLV_NUM_STATIONS;
ar->max_num_vdevs = TARGET_TLV_NUM_VDEVS;
ar->max_num_tdls_vdevs = TARGET_TLV_NUM_TDLS_VDEVS;
@@ -1699,7 +1732,7 @@ static int ath10k_core_init_firmware_features(struct ath10k *ar)
ar->max_spatial_stream = WMI_MAX_SPATIAL_STREAM;
break;
case ATH10K_FW_WMI_OP_VERSION_10_4:
- ar->max_num_peers = TARGET_10_4_NUM_PEERS;
+ max_num_peers = TARGET_10_4_NUM_PEERS;
ar->max_num_stations = TARGET_10_4_NUM_STATIONS;
ar->num_active_peers = TARGET_10_4_ACTIVE_PEERS;
ar->max_num_vdevs = TARGET_10_4_NUM_VDEVS;
@@ -1716,10 +1749,16 @@ static int ath10k_core_init_firmware_features(struct ath10k *ar)
break;
case ATH10K_FW_WMI_OP_VERSION_UNSET:
case ATH10K_FW_WMI_OP_VERSION_MAX:
+ default:
WARN_ON(1);
return -EINVAL;
}
+ if (ar->hw_params.max_num_peers)
+ ar->max_num_peers = ar->hw_params.max_num_peers;
+ else
+ ar->max_num_peers = max_num_peers;
+
/* Backwards compatibility for firmwares without
* ATH10K_FW_IE_HTT_OP_VERSION.
*/
diff --git a/drivers/net/wireless/ath/ath10k/core.h b/drivers/net/wireless/ath/ath10k/core.h
index c58250c..d9d7805 100644
--- a/drivers/net/wireless/ath/ath10k/core.h
+++ b/drivers/net/wireless/ath/ath10k/core.h
@@ -71,13 +71,6 @@
struct ath10k;
-enum ath10k_bus {
- ATH10K_BUS_PCI,
- ATH10K_BUS_AHB,
- ATH10K_BUS_SDIO,
- ATH10K_BUS_USB,
-};
-
static inline const char *ath10k_bus_str(enum ath10k_bus bus)
{
switch (bus) {
diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h
index 9f4cd76..33186be 100644
--- a/drivers/net/wireless/ath/ath10k/hw.h
+++ b/drivers/net/wireless/ath/ath10k/hw.h
@@ -20,6 +20,13 @@
#include "targaddrs.h"
+enum ath10k_bus {
+ ATH10K_BUS_PCI,
+ ATH10K_BUS_AHB,
+ ATH10K_BUS_SDIO,
+ ATH10K_BUS_USB,
+};
+
#define ATH10K_FW_DIR "ath10k"
#define QCA988X_2_0_DEVICE_ID (0x003c)
@@ -120,6 +127,7 @@ enum qca9377_chip_id_rev {
/* QCA9377 1.0 definitions */
#define QCA9377_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA9377/hw1.0"
#define QCA9377_HW_1_0_BOARD_DATA_FILE "board.bin"
+#define QCA9377_HW_1_0_BOARD_DATA_FILE_USB "board-usb.bin"
#define QCA9377_HW_1_0_PATCH_LOAD_ADDR 0x1234
/* QCA4019 1.0 definitions */
@@ -416,6 +424,18 @@ struct ath10k_hw_params {
/* Number of bytes used for alignment in rx_hdr_status of rx desc. */
int decap_align_bytes;
+
+ /* max_num_peers can be used to override the setting derived from
+ * the WMI op version. If this value is non-zero, it will always
+ * be used instead of the default value derived from the WMI op
+ * version.
+ */
+ int max_num_peers;
+
+ /* Specifies whether or not the device is a high latency device */
+ bool is_high_latency;
+
+ enum ath10k_bus bus;
};
struct htt_rx_desc;
@@ -522,6 +542,9 @@ ath10k_rx_desc_get_l3_pad_bytes(struct ath10k_hw_params *hw,
#define TARGET_TLV_NUM_MSDU_DESC (1024 + 32)
#define TARGET_TLV_NUM_WOW_PATTERNS 22
+/* Target specific defines for QCA9377 high latency firmware */
+#define TARGET_QCA9377_HL_NUM_PEERS 15
+
/* Diagnostic Window */
#define CE_DIAG_PIPE 7
diff --git a/drivers/net/wireless/ath/ath10k/wmi-tlv.c b/drivers/net/wireless/ath/ath10k/wmi-tlv.c
index f918802..754d445 100644
--- a/drivers/net/wireless/ath/ath10k/wmi-tlv.c
+++ b/drivers/net/wireless/ath/ath10k/wmi-tlv.c
@@ -1406,7 +1406,7 @@ static struct sk_buff *ath10k_wmi_tlv_op_gen_init(struct ath10k *ar)
cmd->num_host_mem_chunks = __cpu_to_le32(ar->wmi.num_mem_chunks);
cfg->num_vdevs = __cpu_to_le32(TARGET_TLV_NUM_VDEVS);
- cfg->num_peers = __cpu_to_le32(TARGET_TLV_NUM_PEERS);
+ cfg->num_peers = __cpu_to_le32(ar->max_num_peers);
if (test_bit(WMI_SERVICE_RX_FULL_REORDER, ar->wmi.svc_map)) {
cfg->num_offload_peers = __cpu_to_le32(TARGET_TLV_NUM_VDEVS);
@@ -1417,7 +1417,7 @@ static struct sk_buff *ath10k_wmi_tlv_op_gen_init(struct ath10k *ar)
}
cfg->num_peer_keys = __cpu_to_le32(2);
- cfg->num_tids = __cpu_to_le32(TARGET_TLV_NUM_TIDS);
+ cfg->num_tids = __cpu_to_le32(ar->max_num_peers * 2);
cfg->ast_skid_limit = __cpu_to_le32(0x10);
cfg->tx_chain_mask = __cpu_to_le32(0x7);
cfg->rx_chain_mask = __cpu_to_le32(0x7);
--
2.7.4
next prev parent reply other threads:[~2017-01-13 21:35 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-01-13 21:34 [RFC 00/10] ath10k usb support Erik Stromdahl
2017-01-13 21:35 ` [RFC 01/10] ath10k: various usb related definitions Erik Stromdahl
2017-01-13 21:35 ` [RFC 02/10] ath10k: usb support Erik Stromdahl
2017-01-13 21:35 ` [RFC 03/10] ath10k: high_latency detection Erik Stromdahl
2017-01-13 21:35 ` [RFC 04/10] ath10k: new fw fetch functionality Erik Stromdahl
2017-02-10 12:45 ` [RFC,04/10] " Kalle Valo
2017-01-13 21:35 ` [RFC 05/10] ath10k: htt: RX ring config HL support Erik Stromdahl
2017-01-13 21:35 ` [RFC 06/10] ath10k: disable frame aggregation for high latency Erik Stromdahl
2017-01-13 21:35 ` Erik Stromdahl [this message]
2017-01-13 21:35 ` [RFC 08/10] ath10k: add start_once support Erik Stromdahl
2017-01-13 21:35 ` [RFC 09/10] ath10k: htt: High latency TX support Erik Stromdahl
2017-01-13 21:35 ` [RFC 10/10] ath10k: htt: High latency RX support Erik Stromdahl
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1484343309-6327-8-git-send-email-erik.stromdahl@gmail.com \
--to=erik.stromdahl@gmail.com \
--cc=ath10k@lists.infradead.org \
--cc=kvalo@qca.qualcomm.com \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox