From: Amitkumar Karwar <amitkarwar@gmail.com>
To: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org,
Amitkumar Karwar <amit.karwar@redpinesignals.com>,
Prameela Rani Garnepudi <prameela.j04cs@gmail.com>,
Karun Eagalapati <karun256@gmail.com>
Subject: [PATCH 2/3] rsi: sdio: Add WOWLAN support for S4 hibernate state
Date: Mon, 25 Sep 2017 18:51:49 +0530 [thread overview]
Message-ID: <1506345709-4699-1-git-send-email-amitkarwar@gmail.com> (raw)
From: Karun Eagalapati <karun256@gmail.com>
We are disabling of interrupts from firmware in freeze handler.
Also setting power management capability KEEP_MMC_POWER to make
device wakeup for WoWLAN trigger.
At restore, we observed a device reset on some platforms. Hence
reloading of firmware and device initialization is performed.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
---
drivers/net/wireless/rsi/rsi_91x_sdio.c | 109 ++++++++++++++++++++++++++++++++
1 file changed, 109 insertions(+)
diff --git a/drivers/net/wireless/rsi/rsi_91x_sdio.c b/drivers/net/wireless/rsi/rsi_91x_sdio.c
index 28efa17..b8b5795 100644
--- a/drivers/net/wireless/rsi/rsi_91x_sdio.c
+++ b/drivers/net/wireless/rsi/rsi_91x_sdio.c
@@ -1202,9 +1202,118 @@ static int rsi_resume(struct device *dev)
return 0;
}
+static int rsi_freeze(struct device *dev)
+{
+ int ret;
+ struct sdio_func *pfunction = dev_to_sdio_func(dev);
+ struct rsi_hw *adapter = sdio_get_drvdata(pfunction);
+ struct rsi_common *common;
+ struct rsi_91x_sdiodev *sdev;
+
+ rsi_dbg(INFO_ZONE, "SDIO Bus freeze ===>\n");
+
+ if (!adapter) {
+ rsi_dbg(ERR_ZONE, "Device is not ready\n");
+ return -ENODEV;
+ }
+ common = adapter->priv;
+ sdev = (struct rsi_91x_sdiodev *)adapter->rsi_dev;
+
+#ifdef CONFIG_RSI_WOW
+ if ((common->wow_flags & RSI_WOW_ENABLED) &&
+ (common->wow_flags & RSI_WOW_NO_CONNECTION))
+ rsi_dbg(ERR_ZONE,
+ "##### Device can not wake up through WLAN\n");
+#endif
+ ret = rsi_sdio_disable_interrupts(pfunction);
+
+ if (sdev->write_fail)
+ rsi_dbg(INFO_ZONE, "###### Device is not ready #######\n");
+
+ ret = rsi_set_sdio_pm_caps(adapter);
+ if (ret)
+ rsi_dbg(INFO_ZONE, "Setting power management caps failed\n");
+
+ rsi_dbg(INFO_ZONE, "***** RSI module freezed *****\n");
+
+ return 0;
+}
+
+static int rsi_thaw(struct device *dev)
+{
+ struct sdio_func *pfunction = dev_to_sdio_func(dev);
+ struct rsi_hw *adapter = sdio_get_drvdata(pfunction);
+ struct rsi_common *common = adapter->priv;
+
+ rsi_dbg(ERR_ZONE, "SDIO Bus thaw =====>\n");
+
+ common->fsm_state = FSM_CARD_NOT_READY;
+ common->iface_down = true;
+
+ rsi_sdio_enable_interrupts(pfunction);
+
+ rsi_dbg(INFO_ZONE, "***** RSI module thaw done *****\n");
+
+ return 0;
+}
+
+static int rsi_sdio_reinit_device(struct rsi_hw *adapter)
+{
+ struct rsi_91x_sdiodev *sdev = adapter->rsi_dev;
+ struct sdio_func *pfunction = sdev->pfunction;
+ int ii;
+
+ for (ii = 0; ii < NUM_SOFT_QUEUES; ii++)
+ skb_queue_purge(&adapter->priv->tx_queue[ii]);
+
+ rsi_mac80211_detach(adapter);
+
+ /* Initialize device again */
+ sdio_claim_host(pfunction);
+
+ sdio_release_irq(pfunction);
+ rsi_reset_card(pfunction);
+
+ sdio_enable_func(pfunction);
+ rsi_setupcard(adapter);
+ rsi_init_sdio_slave_regs(adapter);
+ sdio_claim_irq(pfunction, rsi_handle_interrupt);
+ rsi_hal_device_init(adapter);
+
+ sdio_release_host(pfunction);
+
+ return 0;
+}
+
+static int rsi_restore(struct device *dev)
+{
+ struct sdio_func *pfunction = dev_to_sdio_func(dev);
+ struct rsi_hw *adapter = sdio_get_drvdata(pfunction);
+ struct rsi_common *common = adapter->priv;
+
+ rsi_dbg(INFO_ZONE, "SDIO Bus restore ======>\n");
+
+ common->fsm_state = FSM_FW_NOT_LOADED;
+ common->iface_down = true;
+
+ /* Initialize device again */
+ rsi_sdio_reinit_device(adapter);
+
+#ifdef CONFIG_RSI_WOW
+ common->wow_flags = 0;
+#endif
+ common->iface_down = false;
+
+ rsi_dbg(INFO_ZONE, "RSI module restored\n");
+
+ return 0;
+}
static const struct dev_pm_ops rsi_pm_ops = {
.suspend = rsi_suspend,
.resume = rsi_resume,
+ .freeze = rsi_freeze,
+ .thaw = rsi_thaw,
+ .restore = rsi_restore,
};
#endif
--
2.7.4
next reply other threads:[~2017-09-25 13:27 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-09-25 13:21 Amitkumar Karwar [this message]
2017-09-26 9:57 ` [PATCH 2/3] rsi: sdio: Add WOWLAN support for S4 hibernate state Kalle Valo
2017-09-27 13:15 ` Amitkumar Karwar
2017-10-11 9:24 ` Kalle Valo
2017-10-12 0:33 ` Brian Norris
2017-10-12 11:55 ` Amitkumar Karwar
2017-10-12 11:51 ` Amitkumar Karwar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1506345709-4699-1-git-send-email-amitkarwar@gmail.com \
--to=amitkarwar@gmail.com \
--cc=amit.karwar@redpinesignals.com \
--cc=karun256@gmail.com \
--cc=kvalo@codeaurora.org \
--cc=linux-wireless@vger.kernel.org \
--cc=prameela.j04cs@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).