* Re: [PATCH net-next v2 00/11] devlink: Add support for region access
2018-07-11 18:48 ` [PATCH net-next v2 00/11] devlink: Add support for region access Jakub Kicinski
@ 2018-07-12 6:21 ` Alex Vesker
2018-08-15 20:25 ` Johannes Berg
1 sibling, 0 replies; 3+ messages in thread
From: Alex Vesker @ 2018-07-12 6:21 UTC (permalink / raw)
To: Jakub Kicinski
Cc: netdev, jiri, dsahern, andrew, rahul.lakkireddy, linux-wireless,
Johannes Berg
On 7/11/2018 9:48 PM, Jakub Kicinski wrote:
> CC: linux-wireless, wifi chips used to have similar problem
>
> On Wed, 11 Jul 2018 13:42:57 +0300, Alex Vesker wrote:
>> This is a proposal which will allow access to driver defined address
>> regions using devlink. Each device can create its supported address
>> regions and register them. A device which exposes a region will allow
>> access to it using devlink.
>>
>> The suggested implementation will allow exposing regions to the user,
>> reading and dumping snapshots taken from different regions.
>> A snapshot represents a memory image of a region taken by the driver.
>>
>> If a device collects a snapshot of an address region it can be later
>> exposed using devlink region read or dump commands.
>> This functionality allows for future analyses on the snapshots to be
>> done.
>>
>> The major benefit of this support is not only to provide access to
>> internal address regions which were inaccessible to the user but also
>> to provide an additional way to debug complex error states using the
>> region snapshots.
>>
>> Implemented commands:
>> $ devlink region help
>> $ devlink region show [ DEV/REGION ]
>> $ devlink region del DEV/REGION snapshot SNAPSHOT_ID
>> $ devlink region dump DEV/REGION [ snapshot SNAPSHOT_ID ]
>> $ devlink region read DEV/REGION [ snapshot SNAPSHOT_ID ]
>> address ADDRESS length length
> You got me excited with the read without snapshot but then you say below
> that it's future work :)
>
>> Show all of the exposed regions with region sizes:
>> $ devlink region show
>> pci/0000:00:05.0/cr-space: size 1048576 snapshot [1 2]
>> pci/0000:00:05.0/fw-health: size 64 snapshot [1 2]
>>
>> Delete a snapshot using:
>> $ devlink region del pci/0000:00:05.0/cr-space snapshot 1
>>
>> Dump a snapshot:
>> $ devlink region dump pci/0000:00:05.0/fw-health snapshot 1
>> 0000000000000000 0014 95dc 0014 9514 0035 1670 0034 db30
>> 0000000000000010 0000 0000 ffff ff04 0029 8c00 0028 8cc8
>> 0000000000000020 0016 0bb8 0016 1720 0000 0000 c00f 3ffc
>> 0000000000000030 bada cce5 bada cce5 bada cce5 bada cce5
>>
>> Read a specific part of a snapshot:
>> $ devlink region read pci/0000:00:05.0/fw-health snapshot 1 address 0
>> length 16
>> 0000000000000000 0014 95dc 0014 9514 0035 1670 0034 db30
>>
>> For more information you can check devlink-region.8 man page
>>
>> Future:
>> There is a plan to extend the support to include a write command
>> as well as performing read and dump live region
> Reading live region would be very interesting and alleviate the need
> for complicated ethtool dump marshalling a number of drivers started
> doing (incl. nfp). Any plans on that?
Yes I plan to also support read of live regions.
Unlike ethtool which works per netdevice this will allow access per PCI
device,
this allows reading region/dump on IPoIB ULP for example, which
cannot implement a vendor specific dump using ethtool.
> Write support I'm less excited about :)
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH net-next v2 00/11] devlink: Add support for region access
2018-07-11 18:48 ` [PATCH net-next v2 00/11] devlink: Add support for region access Jakub Kicinski
2018-07-12 6:21 ` Alex Vesker
@ 2018-08-15 20:25 ` Johannes Berg
1 sibling, 0 replies; 3+ messages in thread
From: Johannes Berg @ 2018-08-15 20:25 UTC (permalink / raw)
To: Jakub Kicinski, Alex Vesker
Cc: netdev, jiri, dsahern, andrew, rahul.lakkireddy, linux-wireless
On Wed, 2018-07-11 at 11:48 -0700, Jakub Kicinski wrote:
> CC: linux-wireless, wifi chips used to have similar problem
>
> On Wed, 11 Jul 2018 13:42:57 +0300, Alex Vesker wrote:
> > This is a proposal which will allow access to driver defined address
> > regions using devlink. Each device can create its supported address
> > regions and register them. A device which exposes a region will allow
> > access to it using devlink.
We usually just implement it for debug dumping, and use devcoredump for
that. How does this overlap? Some of the devcoredump data may be
"synthetic" in the sense that it doesn't really have to be strictly a
device memory region, so it's not quite the same, but what's the
intended use case for this?
johannes
^ permalink raw reply [flat|nested] 3+ messages in thread