linux-wireless.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Maya Erez <merez@codeaurora.org>
To: Kalle Valo <kvalo@codeaurora.org>
Cc: Maya Erez <merez@codeaurora.org>,
	linux-wireless@vger.kernel.org, wil6210@qti.qualcomm.com
Subject: [PATCH 13/16] wil6210: ignore HALP ICR if already handled
Date: Wed, 31 Oct 2018 10:52:21 +0200	[thread overview]
Message-ID: <1540975944-30576-14-git-send-email-merez@codeaurora.org> (raw)
In-Reply-To: <1540975944-30576-1-git-send-email-merez@codeaurora.org>

HALP ICR is set as long as the FW should stay awake.
To prevent its multiple handling the driver masks this IRQ bit.
However, if there is a different MISC ICR before the driver clears
this bit, there is a risk of race condition between HALP mask and
unmask. This race leads to HALP timeout, in case it is mistakenly
masked.
Add an atomic flag to indicate if HALP ICR should be handled.

Signed-off-by: Maya Erez <merez@codeaurora.org>
---
 drivers/net/wireless/ath/wil6210/interrupt.c | 10 +++++++---
 drivers/net/wireless/ath/wil6210/main.c      |  2 ++
 drivers/net/wireless/ath/wil6210/wil6210.h   |  1 +
 3 files changed, 10 insertions(+), 3 deletions(-)

diff --git a/drivers/net/wireless/ath/wil6210/interrupt.c b/drivers/net/wireless/ath/wil6210/interrupt.c
index 5d287a8..a58fccb 100644
--- a/drivers/net/wireless/ath/wil6210/interrupt.c
+++ b/drivers/net/wireless/ath/wil6210/interrupt.c
@@ -575,10 +575,14 @@ static irqreturn_t wil6210_irq_misc(int irq, void *cookie)
 	}
 
 	if (isr & BIT_DMA_EP_MISC_ICR_HALP) {
-		wil_dbg_irq(wil, "irq_misc: HALP IRQ invoked\n");
-		wil6210_mask_halp(wil);
 		isr &= ~BIT_DMA_EP_MISC_ICR_HALP;
-		complete(&wil->halp.comp);
+		if (atomic_read(&wil->halp.handle_icr)) {
+			/* no need to handle HALP ICRs until next vote */
+			atomic_set(&wil->halp.handle_icr, 0);
+			wil_dbg_irq(wil, "irq_misc: HALP IRQ invoked\n");
+			wil6210_mask_halp(wil);
+			complete(&wil->halp.comp);
+		}
 	}
 
 	wil->isr_misc = isr;
diff --git a/drivers/net/wireless/ath/wil6210/main.c b/drivers/net/wireless/ath/wil6210/main.c
index 5303867..5c89c01 100644
--- a/drivers/net/wireless/ath/wil6210/main.c
+++ b/drivers/net/wireless/ath/wil6210/main.c
@@ -1922,6 +1922,8 @@ void wil_halp_vote(struct wil6210_priv *wil)
 
 	if (++wil->halp.ref_cnt == 1) {
 		reinit_completion(&wil->halp.comp);
+		/* mark to IRQ context to handle HALP ICR */
+		atomic_set(&wil->halp.handle_icr, 1);
 		wil6210_set_halp(wil);
 		rc = wait_for_completion_timeout(&wil->halp.comp, to_jiffies);
 		if (!rc) {
diff --git a/drivers/net/wireless/ath/wil6210/wil6210.h b/drivers/net/wireless/ath/wil6210/wil6210.h
index 0f3be3ff..1897d8c 100644
--- a/drivers/net/wireless/ath/wil6210/wil6210.h
+++ b/drivers/net/wireless/ath/wil6210/wil6210.h
@@ -791,6 +791,7 @@ struct wil_halp {
 	struct mutex		lock; /* protect halp ref_cnt */
 	unsigned int		ref_cnt;
 	struct completion	comp;
+	atomic_t		handle_icr;
 };
 
 struct wil_blob_wrapper {
-- 
1.9.1


  parent reply	other threads:[~2018-10-31  8:58 UTC|newest]

Thread overview: 25+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-10-31  8:52 [PATCH 00/16] wil6210 patches Maya Erez
2018-10-31  8:52 ` [PATCH 01/16] wil6210: remove fake support for RXHASH Maya Erez
2018-11-06 16:05   ` Kalle Valo
2018-10-31  8:52 ` [PATCH 02/16] wil6210: fix reset flow for Talyn-mb Maya Erez
2018-10-31  8:52 ` [PATCH 03/16] wil6210: increase RX rings and RX buff array size Maya Erez
2018-10-31  8:52 ` [PATCH 04/16] wil6210: make sure Rx ring sizes are correlated Maya Erez
2018-10-31  8:52 ` [PATCH 05/16] wil6210: add recovery for FW error while in AP mode Maya Erez
2018-10-31  8:52 ` [PATCH 06/16] wil6210: fix memory leak in wil_find_tx_bcast_2 Maya Erez
2018-10-31  8:52 ` [PATCH 07/16] wil6210: refactor disconnect flow Maya Erez
2018-11-06 10:30   ` Kalle Valo
2018-11-06 11:52     ` merez
2018-11-06 12:28       ` Kalle Valo
2018-11-06 12:38         ` merez
2018-11-06 12:40           ` Kalle Valo
2018-10-31  8:52 ` [PATCH 08/16] wil6210: notify cqm packet loss on disable_ap_sme Maya Erez
2018-10-31  8:52 ` [PATCH 09/16] wil6210: add general initialization/size checks Maya Erez
2018-10-31  8:52 ` [PATCH 10/16] wil6210: fix debugfs memory access alignment Maya Erez
2018-10-31  8:52 ` [PATCH 11/16] wil6210: fix L2 RX status handling Maya Erez
2018-10-31  8:52 ` [PATCH 12/16] wil6210: fix RGF_CAF_ICR address for Talyn-MB Maya Erez
2018-10-31  8:52 ` Maya Erez [this message]
2018-11-06 10:04   ` [PATCH 13/16] wil6210: ignore HALP ICR if already handled Kalle Valo
2018-11-06 12:24     ` merez
2018-10-31  8:52 ` [PATCH 14/16] wil6210: remove unnecessary alignment code from rx flow Maya Erez
2018-10-31  8:52 ` [PATCH 15/16] wil6210: fix freeing of rx buffers in EDMA mode Maya Erez
2018-10-31  8:52 ` [PATCH 16/16] wil6210: fix locking in wmi_call Maya Erez

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1540975944-30576-14-git-send-email-merez@codeaurora.org \
    --to=merez@codeaurora.org \
    --cc=kvalo@codeaurora.org \
    --cc=linux-wireless@vger.kernel.org \
    --cc=wil6210@qti.qualcomm.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).