From: Wen Gong <wgong@codeaurora.org>
To: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Subject: [PATCH v3 7/8] ath10k: enable alt data of TX path for sdio
Date: Wed, 28 Aug 2019 21:16:16 +0800 [thread overview]
Message-ID: <1566998177-2658-8-git-send-email-wgong@codeaurora.org> (raw)
In-Reply-To: <1566998177-2658-1-git-send-email-wgong@codeaurora.org>
The default credit size is 1792 bytes, but the IP mtu is 1500 bytes,
then it has about 290 bytes's waste for each data packet on sdio
transfer path for TX bundle, it will reduce the transmission utilization
ratio for data packet.
This patch enable the small credit size in firmware, firmware will use
the new credit size 1556 bytes, it will increase the transmission
utilization ratio for data packet on TX patch. It results in significant
performance improvement on TX path.
This patch only effect sdio chip, it will not effect PCI, SNOC etc.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
---
v2:no change
v3:change some code style
drivers/net/wireless/ath/ath10k/core.c | 19 +++++++++++++++++--
drivers/net/wireless/ath/ath10k/htc.c | 11 +++++++++--
drivers/net/wireless/ath/ath10k/htc.h | 11 +++++++++--
3 files changed, 35 insertions(+), 6 deletions(-)
diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index 9841533..9fd07c7 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -31,6 +31,7 @@
static unsigned int ath10k_cryptmode_param;
static bool uart_print;
static bool disable_tx_comp = true;
+static bool alt_data = true;
static bool skip_otp;
static bool rawmode;
static bool fw_diag_log;
@@ -45,6 +46,15 @@
/* If upper layer need the TX complete status, it can enable tx complete */
module_param(disable_tx_comp, bool, 0644);
+
+/* alt_data is only used for sdio chip, for previous version of firmware, its
+ * alt data size is 1544 which is not enough for native wifi, so it need to
+ * alt_data for the firmware.
+ * If the firmware has changed alt data size to 1556, then it can enable
+ * alt_data for the firmware.
+ * alt_data will not effect PCI, SNOC etc.
+ */
+module_param(alt_data, bool, 0644);
module_param(skip_otp, bool, 0644);
module_param(rawmode, bool, 0644);
module_param(fw_diag_log, bool, 0644);
@@ -698,9 +708,14 @@ static void ath10k_init_sdio(struct ath10k *ar, enum ath10k_firmware_mode mode)
param &= ~HI_ACS_FLAGS_SDIO_REDUCE_TX_COMPL_SET;
/* Alternate credit size of 1544 as used by SDIO firmware is
- * not big enough for mac80211 / native wifi frames. disable it
+ * not big enough for mac80211 / native wifi frames. disable it.
+ * If alternate credit size of 1556 as used by SDIO firmware is
+ * big enough for mac80211 / native wifi frames. enable it
*/
- param &= ~HI_ACS_FLAGS_ALT_DATA_CREDIT_SIZE;
+ if (alt_data && mode == ATH10K_FIRMWARE_MODE_NORMAL)
+ param |= HI_ACS_FLAGS_ALT_DATA_CREDIT_SIZE;
+ else
+ param &= ~HI_ACS_FLAGS_ALT_DATA_CREDIT_SIZE;
if (mode == ATH10K_FIRMWARE_MODE_UTF)
param &= ~HI_ACS_FLAGS_SDIO_SWAP_MAILBOX_SET;
diff --git a/drivers/net/wireless/ath/ath10k/htc.c b/drivers/net/wireless/ath/ath10k/htc.c
index 5269168..04298e1 100644
--- a/drivers/net/wireless/ath/ath10k/htc.c
+++ b/drivers/net/wireless/ath/ath10k/htc.c
@@ -940,12 +940,15 @@ int ath10k_htc_wait_target(struct ath10k_htc *htc)
*/
if (htc->control_resp_len >=
sizeof(msg->hdr) + sizeof(msg->ready_ext)) {
+ htc->alt_data_credit_size =
+ __le16_to_cpu(msg->ready_ext.reserved) & 0x0fff;
htc->max_msgs_per_htc_bundle =
min_t(u8, msg->ready_ext.max_msgs_per_htc_bundle,
HTC_HOST_MAX_MSG_PER_RX_BUNDLE);
ath10k_dbg(ar, ATH10K_DBG_HTC,
- "Extended ready message. RX bundle size: %d\n",
- htc->max_msgs_per_htc_bundle);
+ "Extended ready message. RX bundle size: %d, alt size:%d\n",
+ htc->max_msgs_per_htc_bundle,
+ htc->alt_data_credit_size);
}
INIT_WORK(&ar->bundle_tx_work, ath10k_htc_bundle_tx_work);
@@ -1097,6 +1100,10 @@ int ath10k_htc_connect_service(struct ath10k_htc *htc,
ep->tx_credits = tx_alloc;
ep->tx_credit_size = htc->target_credit_size;
+ if (conn_req->service_id == ATH10K_HTC_SVC_ID_HTT_DATA_MSG &&
+ htc->alt_data_credit_size != 0)
+ ep->tx_credit_size = htc->alt_data_credit_size;
+
/* copy all the callbacks */
ep->ep_ops = conn_req->ep_ops;
diff --git a/drivers/net/wireless/ath/ath10k/htc.h b/drivers/net/wireless/ath/ath10k/htc.h
index 7b8e0d0..f3a6ebb 100644
--- a/drivers/net/wireless/ath/ath10k/htc.h
+++ b/drivers/net/wireless/ath/ath10k/htc.h
@@ -141,8 +141,14 @@ struct ath10k_htc_ready_extended {
struct ath10k_htc_ready base;
u8 htc_version; /* @enum ath10k_htc_version */
u8 max_msgs_per_htc_bundle;
- u8 pad0;
- u8 pad1;
+ union {
+ __le16 reserved;
+ struct {
+ u8 pad0;
+ u8 pad1;
+ } __packed;
+ } __packed;
+
} __packed;
struct ath10k_htc_conn_svc {
@@ -379,6 +385,7 @@ struct ath10k_htc {
int total_transmit_credits;
int target_credit_size;
u8 max_msgs_per_htc_bundle;
+ int alt_data_credit_size;
};
int ath10k_htc_init(struct ath10k *ar);
--
1.9.1
next prev parent reply other threads:[~2019-08-29 17:39 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-08-28 13:16 [PATCH v3 0/8] ath10k: improve throughout of tcp/udp TX/RX of sdio Wen Gong
2019-08-28 13:16 ` [PATCH v3 1/8] ath10k: adjust skb length in ath10k_sdio_mbox_rx_packet Wen Gong
2019-08-30 2:53 ` Nicolas Boichat
2019-08-30 2:58 ` Nicolas Boichat
2019-09-04 2:42 ` Wen Gong
2019-08-28 13:16 ` [PATCH v3 2/8] ath10k: enable RX bundle receive for sdio Wen Gong
2019-08-30 3:07 ` Nicolas Boichat
2019-09-04 2:43 ` Wen Gong
2019-09-04 2:48 ` Wen Gong
2019-08-28 13:16 ` [PATCH v3 3/8] ath10k: change max RX bundle size from 8 to 32 " Wen Gong
2019-08-30 3:11 ` Nicolas Boichat
2019-09-04 2:52 ` Wen Gong
2019-08-28 13:16 ` [PATCH v3 4/8] ath10k: add workqueue for RX path of sdio Wen Gong
2019-09-04 2:53 ` Wen Gong
2019-08-28 13:16 ` [PATCH v3 5/8] ath10k: disable TX complete indication of htt for sdio Wen Gong
2019-09-04 2:54 ` Wen Gong
2019-08-28 13:16 ` [PATCH v3 6/8] ath10k: add htt TX bundle " Wen Gong
2019-09-04 2:56 ` Wen Gong
2019-08-28 13:16 ` Wen Gong [this message]
2019-08-30 3:18 ` [PATCH v3 7/8] ath10k: enable alt data of TX path " Nicolas Boichat
2019-09-04 2:58 ` Wen Gong
2019-08-28 13:16 ` [PATCH v3 8/8] ath10k: enable napi on RX " Wen Gong
2019-08-30 3:19 ` Nicolas Boichat
2019-09-04 2:59 ` Wen Gong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1566998177-2658-8-git-send-email-wgong@codeaurora.org \
--to=wgong@codeaurora.org \
--cc=ath10k@lists.infradead.org \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox