From: Florian Fainelli <florian@openwrt.org>
To: Hauke Mehrtens <hauke@hauke-m.de>
Cc: ralf@linux-mips.org, linux-mips@linux-mips.org,
linux-wireless@vger.kernel.org, john@phrozen.org
Subject: Re: [PATCH v2 3/3] MIPS: BCM47xx: rewrite GPIO handling and use gpiolib
Date: Thu, 16 Aug 2012 18:26:18 +0200 [thread overview]
Message-ID: <1791263.5FQJJv4xHF@bender> (raw)
In-Reply-To: <1345132801-8430-4-git-send-email-hauke@hauke-m.de>
Hello Hauke,
On Thursday 16 August 2012 18:00:01 Hauke Mehrtens wrote:
> The original implementation implemented functions like gpio_request()
> itself, but it missed some new functions added to the GPIO interface.
> This caused compile problems for some drivers using some of the special
> request methods which where not implemented. Now it uses gpiolib and
> this implements all the request methods needed.
>
> The raw GPIO register access methods like bcm47xx_gpio_in() are
> exported, because some special drivers for this target, not yet in
> mainline, need them.
>
> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
> ---
[snip]
>
> -int gpio_request(unsigned gpio, const char *tag)
> +static unsigned long bcm47xx_gpio_count;
> +
> +/* low level BCM47xx gpio api */
> +u32 bcm47xx_gpio_in(u32 mask)
Are you using these low-level helpers beyond the scope of this file? I do not
see them being used anywhere else. You might just mark them as static inline.
> {
> switch (bcm47xx_bus_type) {
> #ifdef CONFIG_BCM47XX_SSB
> case BCM47XX_BUS_TYPE_SSB:
> - if (ssb_chipco_available(&bcm47xx_bus.ssb.chipco) &&
> - ((unsigned)gpio >= BCM47XX_CHIPCO_GPIO_LINES))
> - return -EINVAL;
> -
> - if (ssb_extif_available(&bcm47xx_bus.ssb.extif) &&
> - ((unsigned)gpio >= BCM47XX_EXTIF_GPIO_LINES))
> - return -EINVAL;
> -
> - if (test_and_set_bit(gpio, gpio_in_use))
> - return -EBUSY;
> -
> - return 0;
> + return ssb_gpio_in(&bcm47xx_bus.ssb, mask);
> #endif
> #ifdef CONFIG_BCM47XX_BCMA
> case BCM47XX_BUS_TYPE_BCMA:
> - if (gpio >= BCM47XX_CHIPCO_GPIO_LINES)
> - return -EINVAL;
> -
> - if (test_and_set_bit(gpio, gpio_in_use))
> - return -EBUSY;
> + return bcma_gpio_in(&bcm47xx_bus.bcma.bus, mask);
> +#endif
> + }
> + return -EINVAL;
> +}
> +EXPORT_SYMBOL(bcm47xx_gpio_in);
>
> - return 0;
> +u32 bcm47xx_gpio_out(u32 mask, u32 value)
> +{
> + switch (bcm47xx_bus_type) {
> +#ifdef CONFIG_BCM47XX_SSB
> + case BCM47XX_BUS_TYPE_SSB:
> + return ssb_gpio_out(&bcm47xx_bus.ssb, mask, value);
> +#endif
> +#ifdef CONFIG_BCM47XX_BCMA
> + case BCM47XX_BUS_TYPE_BCMA:
> + return bcma_gpio_out(&bcm47xx_bus.bcma.bus, mask, value);
> #endif
> }
> return -EINVAL;
> }
> -EXPORT_SYMBOL(gpio_request);
> +EXPORT_SYMBOL(bcm47xx_gpio_out);
>
> -void gpio_free(unsigned gpio)
> +u32 bcm47xx_gpio_outen(u32 mask, u32 value)
> {
> switch (bcm47xx_bus_type) {
> #ifdef CONFIG_BCM47XX_SSB
> case BCM47XX_BUS_TYPE_SSB:
> - if (ssb_chipco_available(&bcm47xx_bus.ssb.chipco) &&
> - ((unsigned)gpio >= BCM47XX_CHIPCO_GPIO_LINES))
> - return;
> + return ssb_gpio_outen(&bcm47xx_bus.ssb, mask, value);
> +#endif
> +#ifdef CONFIG_BCM47XX_BCMA
> + case BCM47XX_BUS_TYPE_BCMA:
> + return bcma_gpio_outen(&bcm47xx_bus.bcma.bus, mask, value);
> +#endif
> + }
> + return -EINVAL;
> +}
> +EXPORT_SYMBOL(bcm47xx_gpio_outen);
>
> - if (ssb_extif_available(&bcm47xx_bus.ssb.extif) &&
> - ((unsigned)gpio >= BCM47XX_EXTIF_GPIO_LINES))
> - return;
> +u32 bcm47xx_gpio_control(u32 mask, u32 value)
> +{
> + switch (bcm47xx_bus_type) {
> +#ifdef CONFIG_BCM47XX_SSB
> + case BCM47XX_BUS_TYPE_SSB:
> + return ssb_gpio_control(&bcm47xx_bus.ssb, mask, value);
> +#endif
> +#ifdef CONFIG_BCM47XX_BCMA
> + case BCM47XX_BUS_TYPE_BCMA:
> + return bcma_gpio_control(&bcm47xx_bus.bcma.bus, mask, value);
> +#endif
> + }
> + return -EINVAL;
> +}
> +EXPORT_SYMBOL(bcm47xx_gpio_control);
>
> - clear_bit(gpio, gpio_in_use);
> - return;
> +u32 bcm47xx_gpio_intmask(u32 mask, u32 value)
> +{
> + switch (bcm47xx_bus_type) {
> +#ifdef CONFIG_BCM47XX_SSB
> + case BCM47XX_BUS_TYPE_SSB:
> + return ssb_gpio_intmask(&bcm47xx_bus.ssb, mask, value);
> #endif
> #ifdef CONFIG_BCM47XX_BCMA
> case BCM47XX_BUS_TYPE_BCMA:
> - if (gpio >= BCM47XX_CHIPCO_GPIO_LINES)
> - return;
> + return bcma_gpio_intmask(&bcm47xx_bus.bcma.bus, mask, value);
> +#endif
> + }
> + return -EINVAL;
> +}
> +EXPORT_SYMBOL(bcm47xx_gpio_intmask);
>
> - clear_bit(gpio, gpio_in_use);
> - return;
> +u32 bcm47xx_gpio_polarity(u32 mask, u32 value)
> +{
> + switch (bcm47xx_bus_type) {
> +#ifdef CONFIG_BCM47XX_SSB
> + case BCM47XX_BUS_TYPE_SSB:
> + return ssb_gpio_polarity(&bcm47xx_bus.ssb, mask, value);
> +#endif
> +#ifdef CONFIG_BCM47XX_BCMA
> + case BCM47XX_BUS_TYPE_BCMA:
> + return bcma_gpio_polarity(&bcm47xx_bus.bcma.bus, mask, value);
> #endif
> }
> + return -EINVAL;
> +}
> +EXPORT_SYMBOL(bcm47xx_gpio_polarity);
> +
> +
> +static int bcm47xx_gpio_get_value(struct gpio_chip *chip, unsigned gpio)
> +{
> + return bcm47xx_gpio_in(1 << gpio);
> +}
> +
> +static void bcm47xx_gpio_set_value(struct gpio_chip *chip,
> + unsigned gpio, int value)
> +{
> + bcm47xx_gpio_out(1 << gpio, value ? 1 << gpio : 0);
> +}
> +
> +static int bcm47xx_gpio_direction_input(struct gpio_chip *chip,
> + unsigned gpio)
> +{
> + bcm47xx_gpio_outen(1 << gpio, 0);
> + return 0;
> +}
> +
> +static int bcm47xx_gpio_direction_output(struct gpio_chip *chip,
> + unsigned gpio, int value)
> +{
> + /* first set the gpio out value */
> + bcm47xx_gpio_out(1 << gpio, value ? 1 << gpio : 0);
> + /* then set the gpio mode */
> + bcm47xx_gpio_outen(1 << gpio, 1 << gpio);
> + return 0;
> }
Ok, so either mark the low-level helpers static inline, or just get rid of
them and make the gpiolib callbacks use the same code directly, I do not think
there is a need for such an indirection level.
> -EXPORT_SYMBOL(gpio_free);
>
> -int gpio_to_irq(unsigned gpio)
> +static int bcm47xx_gpio_to_irq(struct gpio_chip *chip, unsigned gpio)
> {
> switch (bcm47xx_bus_type) {
> #ifdef CONFIG_BCM47XX_SSB
> @@ -99,4 +166,53 @@ int gpio_to_irq(unsigned gpio)
> }
> return -EINVAL;
> }
> -EXPORT_SYMBOL_GPL(gpio_to_irq);
> +
> +static struct gpio_chip bcm47xx_gpio_chip = {
> + .label = "bcm47xx",
> + .get = bcm47xx_gpio_get_value,
> + .set = bcm47xx_gpio_set_value,
> + .direction_input = bcm47xx_gpio_direction_input,
> + .direction_output = bcm47xx_gpio_direction_output,
> + .to_irq = bcm47xx_gpio_to_irq,
> + .base = 0,
> +};
> +
> +void __init bcm47xx_gpio_init(void)
> +{
> + int err;
> +
> + switch (bcm47xx_bus_type) {
> +#ifdef CONFIG_BCM47XX_SSB
> + case BCM47XX_BUS_TYPE_SSB:
> + bcm47xx_gpio_count = ssb_gpio_count(&bcm47xx_bus.ssb);
> +#endif
> +#ifdef CONFIG_BCM47XX_BCMA
> + case BCM47XX_BUS_TYPE_BCMA:
> + bcm47xx_gpio_count = bcma_gpio_count(&bcm47xx_bus.bcma.bus);
> +#endif
> + }
Is this exclusive? Cannot we have both SSB and BCMA on the same device?
> +
> + bcm47xx_gpio_chip.ngpio = bcm47xx_gpio_count;
> +
> + err = gpiochip_add(&bcm47xx_gpio_chip);
> + if (err)
> + panic("cannot add BCM47xx GPIO chip, error=%d", err);
> +}
> +
> +int gpio_get_value(unsigned gpio)
> +{
> + if (gpio < bcm47xx_gpio_count)
> + return bcm47xx_gpio_in(1 << gpio);
> +
> + return __gpio_get_value(gpio);
> +}
> +EXPORT_SYMBOL(gpio_get_value);
> +
> +void gpio_set_value(unsigned gpio, int value)
> +{
> + if (gpio < bcm47xx_gpio_count)
> + bcm47xx_gpio_out(1 << gpio, value ? 1 << gpio : 0);
> + else
> + __gpio_set_value(gpio, value);
> +}
> +EXPORT_SYMBOL(gpio_set_value);
Why do we need these stubs?
> diff --git a/arch/mips/bcm47xx/setup.c b/arch/mips/bcm47xx/setup.c
> index 95bf4d7..2936532 100644
> --- a/arch/mips/bcm47xx/setup.c
> +++ b/arch/mips/bcm47xx/setup.c
> @@ -220,6 +220,8 @@ void __init plat_mem_setup(void)
> _machine_restart = bcm47xx_machine_restart;
> _machine_halt = bcm47xx_machine_halt;
> pm_power_off = bcm47xx_machine_halt;
> +
> + bcm47xx_gpio_init();
> }
>
> static int __init bcm47xx_register_bus_complete(void)
> diff --git a/arch/mips/bcm47xx/wgt634u.c b/arch/mips/bcm47xx/wgt634u.c
> index e9f9ec8..fd1066e 100644
> --- a/arch/mips/bcm47xx/wgt634u.c
> +++ b/arch/mips/bcm47xx/wgt634u.c
> @@ -133,6 +133,7 @@ static int __init wgt634u_init(void)
> * been allocated ranges 00:09:5b:xx:xx:xx and 00:0f:b5:xx:xx:xx.
> */
> u8 *et0mac;
> + int err;
>
> if (bcm47xx_bus_type != BCM47XX_BUS_TYPE_SSB)
> return -ENODEV;
> @@ -146,6 +147,12 @@ static int __init wgt634u_init(void)
>
> printk(KERN_INFO "WGT634U machine detected.\n");
>
> + err = gpio_request(WGT634U_GPIO_RESET, "reset-buton");
> + if (err) {
> + printk(KERN_INFO "Can not register gpio for reset button\n");
> + return 0;
> + }
> +
> if (!request_irq(gpio_to_irq(WGT634U_GPIO_RESET),
> gpio_interrupt, IRQF_SHARED,
> "WGT634U GPIO", &bcm47xx_bus.ssb.chipco)) {
> diff --git a/arch/mips/include/asm/mach-bcm47xx/bcm47xx.h
b/arch/mips/include/asm/mach-bcm47xx/bcm47xx.h
> index 26fdaf4..1bd5560 100644
> --- a/arch/mips/include/asm/mach-bcm47xx/bcm47xx.h
> +++ b/arch/mips/include/asm/mach-bcm47xx/bcm47xx.h
> @@ -56,4 +56,6 @@ void bcm47xx_fill_bcma_boardinfo(struct bcma_boardinfo
*boardinfo,
> const char *prefix);
> #endif
>
> +void bcm47xx_gpio_init(void);
> +
> #endif /* __ASM_BCM47XX_H */
> diff --git a/arch/mips/include/asm/mach-bcm47xx/gpio.h
b/arch/mips/include/asm/mach-bcm47xx/gpio.h
> index 2ef17e8..27a5632 100644
> --- a/arch/mips/include/asm/mach-bcm47xx/gpio.h
> +++ b/arch/mips/include/asm/mach-bcm47xx/gpio.h
> @@ -4,152 +4,42 @@
> * for more details.
> *
> * Copyright (C) 2007 Aurelien Jarno <aurelien@aurel32.net>
> + * Copyright (C) 2012 Hauke Mehrtens <hauke@hauke-m.de>
> */
>
> #ifndef __BCM47XX_GPIO_H
> #define __BCM47XX_GPIO_H
>
> -#include <linux/ssb/ssb_embedded.h>
> -#include <linux/bcma/bcma.h>
> -#include <asm/mach-bcm47xx/bcm47xx.h>
> +#define ARCH_NR_GPIOS 64
> +#include <asm-generic/gpio.h>
>
> -#define BCM47XX_EXTIF_GPIO_LINES 5
> -#define BCM47XX_CHIPCO_GPIO_LINES 16
> +/* low level BCM47xx gpio api */
> +u32 bcm47xx_gpio_in(u32 mask);
> +u32 bcm47xx_gpio_out(u32 mask, u32 value);
> +u32 bcm47xx_gpio_outen(u32 mask, u32 value);
> +u32 bcm47xx_gpio_control(u32 mask, u32 value);
> +u32 bcm47xx_gpio_intmask(u32 mask, u32 value);
> +u32 bcm47xx_gpio_polarity(u32 mask, u32 value);
>
> -extern int gpio_request(unsigned gpio, const char *label);
> -extern void gpio_free(unsigned gpio);
> -extern int gpio_to_irq(unsigned gpio);
> +int gpio_get_value(unsigned gpio);
> +void gpio_set_value(unsigned gpio, int value);
>
> -static inline int gpio_get_value(unsigned gpio)
> +static inline void gpio_intmask(unsigned gpio, int value)
> {
> - switch (bcm47xx_bus_type) {
> -#ifdef CONFIG_BCM47XX_SSB
> - case BCM47XX_BUS_TYPE_SSB:
> - return ssb_gpio_in(&bcm47xx_bus.ssb, 1 << gpio);
> -#endif
> -#ifdef CONFIG_BCM47XX_BCMA
> - case BCM47XX_BUS_TYPE_BCMA:
> - return bcma_chipco_gpio_in(&bcm47xx_bus.bcma.bus.drv_cc,
> - 1 << gpio);
> -#endif
> - }
> - return -EINVAL;
> -}
> -
> -#define gpio_get_value_cansleep gpio_get_value
> -
> -static inline void gpio_set_value(unsigned gpio, int value)
> -{
> - switch (bcm47xx_bus_type) {
> -#ifdef CONFIG_BCM47XX_SSB
> - case BCM47XX_BUS_TYPE_SSB:
> - ssb_gpio_out(&bcm47xx_bus.ssb, 1 << gpio,
> - value ? 1 << gpio : 0);
> - return;
> -#endif
> -#ifdef CONFIG_BCM47XX_BCMA
> - case BCM47XX_BUS_TYPE_BCMA:
> - bcma_chipco_gpio_out(&bcm47xx_bus.bcma.bus.drv_cc, 1 << gpio,
> - value ? 1 << gpio : 0);
> - return;
> -#endif
> - }
> -}
> -
> -#define gpio_set_value_cansleep gpio_set_value
> -
> -static inline int gpio_cansleep(unsigned gpio)
> -{
> - return 0;
> -}
> -
> -static inline int gpio_is_valid(unsigned gpio)
> -{
> - return gpio < (BCM47XX_EXTIF_GPIO_LINES + BCM47XX_CHIPCO_GPIO_LINES);
> -}
> -
> -
> -static inline int gpio_direction_input(unsigned gpio)
> -{
> - switch (bcm47xx_bus_type) {
> -#ifdef CONFIG_BCM47XX_SSB
> - case BCM47XX_BUS_TYPE_SSB:
> - ssb_gpio_outen(&bcm47xx_bus.ssb, 1 << gpio, 0);
> - return 0;
> -#endif
> -#ifdef CONFIG_BCM47XX_BCMA
> - case BCM47XX_BUS_TYPE_BCMA:
> - bcma_chipco_gpio_outen(&bcm47xx_bus.bcma.bus.drv_cc, 1 << gpio,
> - 0);
> - return 0;
> -#endif
> - }
> - return -EINVAL;
> + bcm47xx_gpio_intmask(1 << gpio, value ? 1 << gpio : 0);
> }
>
> -static inline int gpio_direction_output(unsigned gpio, int value)
> +static inline void gpio_polarity(unsigned gpio, int value)
> {
> - switch (bcm47xx_bus_type) {
> -#ifdef CONFIG_BCM47XX_SSB
> - case BCM47XX_BUS_TYPE_SSB:
> - /* first set the gpio out value */
> - ssb_gpio_out(&bcm47xx_bus.ssb, 1 << gpio,
> - value ? 1 << gpio : 0);
> - /* then set the gpio mode */
> - ssb_gpio_outen(&bcm47xx_bus.ssb, 1 << gpio, 1 << gpio);
> - return 0;
> -#endif
> -#ifdef CONFIG_BCM47XX_BCMA
> - case BCM47XX_BUS_TYPE_BCMA:
> - /* first set the gpio out value */
> - bcma_chipco_gpio_out(&bcm47xx_bus.bcma.bus.drv_cc, 1 << gpio,
> - value ? 1 << gpio : 0);
> - /* then set the gpio mode */
> - bcma_chipco_gpio_outen(&bcm47xx_bus.bcma.bus.drv_cc, 1 << gpio,
> - 1 << gpio);
> - return 0;
> -#endif
> - }
> - return -EINVAL;
> -}
> -
> -static inline int gpio_intmask(unsigned gpio, int value)
> -{
> - switch (bcm47xx_bus_type) {
> -#ifdef CONFIG_BCM47XX_SSB
> - case BCM47XX_BUS_TYPE_SSB:
> - ssb_gpio_intmask(&bcm47xx_bus.ssb, 1 << gpio,
> - value ? 1 << gpio : 0);
> - return 0;
> -#endif
> -#ifdef CONFIG_BCM47XX_BCMA
> - case BCM47XX_BUS_TYPE_BCMA:
> - bcma_chipco_gpio_intmask(&bcm47xx_bus.bcma.bus.drv_cc,
> - 1 << gpio, value ? 1 << gpio : 0);
> - return 0;
> -#endif
> - }
> - return -EINVAL;
> + bcm47xx_gpio_polarity(1 << gpio, value ? 1 << gpio : 0);
> }
>
> -static inline int gpio_polarity(unsigned gpio, int value)
> +static inline int irq_to_gpio(int gpio)
> {
> - switch (bcm47xx_bus_type) {
> -#ifdef CONFIG_BCM47XX_SSB
> - case BCM47XX_BUS_TYPE_SSB:
> - ssb_gpio_polarity(&bcm47xx_bus.ssb, 1 << gpio,
> - value ? 1 << gpio : 0);
> - return 0;
> -#endif
> -#ifdef CONFIG_BCM47XX_BCMA
> - case BCM47XX_BUS_TYPE_BCMA:
> - bcma_chipco_gpio_polarity(&bcm47xx_bus.bcma.bus.drv_cc,
> - 1 << gpio, value ? 1 << gpio : 0);
> - return 0;
> -#endif
> - }
> return -EINVAL;
> }
>
> +#define gpio_cansleep __gpio_cansleep
> +#define gpio_to_irq __gpio_to_irq
>
> #endif /* __BCM47XX_GPIO_H */
>
--
Florian
next prev parent reply other threads:[~2012-08-16 16:26 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-08-16 15:59 [PATCH v2 0/3] MIPS: BCM47xx: use gpiolib Hauke Mehrtens
2012-08-16 15:59 ` [PATCH v2 1/3] ssb: add function to return number of gpio lines Hauke Mehrtens
2012-08-16 16:00 ` [PATCH v2 2/3] bcma: add GPIO driver for SoCs Hauke Mehrtens
2012-08-16 16:00 ` [PATCH v2 3/3] MIPS: BCM47xx: rewrite GPIO handling and use gpiolib Hauke Mehrtens
2012-08-16 16:26 ` Florian Fainelli [this message]
2012-08-16 17:39 ` Rafał Miłecki
2012-08-16 18:43 ` Arend van Spriel
2012-08-16 19:29 ` Rafał Miłecki
2012-08-16 22:38 ` Hauke Mehrtens
2012-08-16 22:28 ` Hauke Mehrtens
2012-08-16 19:35 ` John Crispin
2012-08-16 22:33 ` Hauke Mehrtens
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1791263.5FQJJv4xHF@bender \
--to=florian@openwrt.org \
--cc=hauke@hauke-m.de \
--cc=john@phrozen.org \
--cc=linux-mips@linux-mips.org \
--cc=linux-wireless@vger.kernel.org \
--cc=ralf@linux-mips.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).