From: Pavel Roskin <proski@gnu.org>
To: John Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Subject: [PATCH 24/26] at76_usb: Use ETH_P_802_2 in monitor mode
Date: Sun, 30 Sep 2007 14:41:12 -0400 [thread overview]
Message-ID: <20070930184112.23921.96075.stgit@tt.roinet.com> (raw)
In-Reply-To: <20070930183409.23921.97762.stgit@tt.roinet.com>
It's used by most other wireless drivers, including mac80211.
ETH_P_80211_RAW is obsolete.
Signed-off-by: Pavel Roskin <proski@gnu.org>
---
drivers/net/wireless/at76_usb.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
diff --git a/drivers/net/wireless/at76_usb.c b/drivers/net/wireless/at76_usb.c
index 1e3363e..f67dc8e 100644
--- a/drivers/net/wireless/at76_usb.c
+++ b/drivers/net/wireless/at76_usb.c
@@ -4937,7 +4937,7 @@ static void at76_rx_monitor_mode(struct at76_priv *priv)
skb->ip_summed = CHECKSUM_NONE;
skb_reset_mac_header(skb);
skb->pkt_type = PACKET_OTHERHOST;
- skb->protocol = htons(ETH_P_80211_RAW);
+ skb->protocol = htons(ETH_P_802_2);
netdev->last_rx = jiffies;
netif_rx(skb);
next prev parent reply other threads:[~2007-09-30 18:41 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-09-30 18:38 [PATCH 00/26] at76_usb: bring up to date Pavel Roskin
2007-09-30 18:38 ` [PATCH 01/26] at76_usb: Use USB_DEVICE_DATA to improve readability of the device table Pavel Roskin
2007-09-30 18:38 ` [PATCH 02/26] at76_usb: Fix some device names in " Pavel Roskin
2007-09-30 18:38 ` [PATCH 03/26] at76_usb: Avoid dubious use of '\0' Pavel Roskin
2007-09-30 18:39 ` [PATCH 04/26] at76_usb: Don't clean priv->mib_buf, just clean data explicitly if needed Pavel Roskin
2007-09-30 18:39 ` [PATCH 05/26] at76_usb: No need to reserve 72 bytes in set_mib_buffer - we only need 6 Pavel Roskin
2007-09-30 18:39 ` [PATCH 06/26] at76_usb: Fix turning radio off Pavel Roskin
2007-09-30 18:39 ` [PATCH 07/26] at76_usb: Integrate at76_set_monitor_mode() into at76_dwork_restart() Pavel Roskin
2007-09-30 18:39 ` [PATCH 08/26] at76_usb: Eliminate err(), it's USB specific Pavel Roskin
2007-09-30 18:39 ` [PATCH 09/26] at76_usb: Remove commented out code for multicast support Pavel Roskin
2007-09-30 18:39 ` [PATCH 10/26] at76_usb: Rename tlv to ie for readability Pavel Roskin
2007-09-30 18:39 ` [PATCH 11/26] at76_usb: Stop worrying about line termination in ethtool info Pavel Roskin
2007-09-30 18:39 ` [PATCH 12/26] at76_usb: Use string precision to avoid line termination Pavel Roskin
2007-09-30 18:40 ` [PATCH 13/26] at76_usb: Eliminate variables used only in at76_dbg() Pavel Roskin
2007-09-30 18:40 ` [PATCH 14/26] at76_usb: Make it clear that management frames are sent at 1Mbps Pavel Roskin
2007-09-30 18:40 ` [PATCH 15/26] at76_usb: Clean reserved tx area for mgmt frames like it's done for data Pavel Roskin
2007-09-30 18:40 ` [PATCH 16/26] at76_usb: Remove unneeded memset() calls Pavel Roskin
2007-09-30 18:40 ` [PATCH 17/26] at76_usb: Move some parts from at76_usb.h to at76_usb.c Pavel Roskin
2007-09-30 18:40 ` [PATCH 18/26] at76_usb: Avoid dealing with milliseconds when possible, use jiffies Pavel Roskin
2007-09-30 18:40 ` [PATCH 19/26] at76_usb: Add ID for Corega Wireless LAN USB-11 mini and mini2 Pavel Roskin
2007-09-30 18:40 ` [PATCH 20/26] at76_usb: Revert to network device names starting with "wlan" Pavel Roskin
2007-09-30 18:40 ` [PATCH 21/26] at76_usb: Remove incorrect firmware version check Pavel Roskin
2007-09-30 18:40 ` [PATCH 22/26] at76_usb: Use dev_printk() where possible Pavel Roskin
2007-09-30 18:41 ` [PATCH 23/26] at76_usb: Be more verbose on startup Pavel Roskin
2007-09-30 18:41 ` Pavel Roskin [this message]
2007-09-30 18:41 ` [PATCH 25/26] at76_usb: Bump version to 0.17 Pavel Roskin
2007-09-30 18:41 ` [PATCH 26/26] at76_usb: Add ID for at76c503a based CNETUSB611 Pavel Roskin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20070930184112.23921.96075.stgit@tt.roinet.com \
--to=proski@gnu.org \
--cc=linux-wireless@vger.kernel.org \
--cc=linville@tuxdriver.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).