From: "Rafael J. Wysocki" <rjw@sisk.pl>
To: Pavel Machek <pavel@ucw.cz>
Cc: linux-wireless@vger.kernel.org,
kernel list <linux-kernel@vger.kernel.org>,
ipw3945-devel@lists.sourceforge.net, yi.zhu@intel.com
Subject: Re: iwl3945 in 2.6.24-rc1 dies under load
Date: Thu, 1 Nov 2007 02:59:04 +0100 [thread overview]
Message-ID: <200711010259.05315.rjw@sisk.pl> (raw)
In-Reply-To: <20071031005202.GA1534@elf.ucw.cz>
On Wednesday, 31 October 2007 01:52, Pavel Machek wrote:
>
> Hi!
>
> ...does not seem to work too well :-(. It connects with the AP
> (good!), and survives some "normal" use, but it died at first big
> tcpspray (baaaad!).
Is this a regression from 2.6.23?
> Oct 31 01:03:57 amd log1n[1411]: ROOT LOGIN on `tty6'
> Oct 31 01:05:06 amd kernel: iwl3945: Intel(R) PRO/Wireless 3945ABG/BG
> Network Connection driver for Linux, 1.1.17kds
> Oct 31 01:05:06 amd kernel: iwl3945: Copyright(c) 2003-2007 Intel
> Corporation
> Oct 31 01:05:06 amd kernel: PCI: Setting latency timer of device
> 0000:03:00.0 to 64
> Oct 31 01:05:06 amd kernel: iwl3945: Detected Intel PRO/Wireless
> 3945ABG Network Connection
> Oct 31 01:05:07 amd kernel: iwl3945: Tunable channels: 11 802.11bg, 13
> 802.11a channels
> Oct 31 01:05:07 amd kernel: phy4: Selected rate control algorithm
> 'simple'
> Oct 31 01:06:05 amd kernel: wlan0: Initial auth_alg=0
> Oct 31 01:06:05 amd kernel: wlan0: authenticate with AP
> 00:11:2f:0e:95:a0
> Oct 31 01:06:05 amd kernel: wlan0: RX authentication from
> 00:11:2f:0e:95:a0 (alg=0 transaction=2 status=0)
> Oct 31 01:06:05 amd kernel: wlan0: authenticated
> Oct 31 01:06:05 amd kernel: wlan0: associate with AP 00:11:2f:0e:95:a0
> Oct 31 01:06:05 amd kernel: wlan0: RX AssocResp from 00:11:2f:0e:95:a0
> (capab=0x401 status=0 aid=1)
> Oct 31 01:06:05 amd kernel: wlan0: associated
> Oct 31 01:06:05 amd kernel: wlan0: switched to short barker preamble
> (BSSID=00:11:2f:0e:95:a0)
> Oct 31 01:06:05 amd kernel: iwl3945: iwl-3945-rs not selected as rate
> control algo!
> Oct 31 01:23:52 amd kernel: wlan0: RX deauthentication from
> 00:11:2f:0e:95:a0 (reason=4)
> Oct 31 01:23:52 amd kernel: wlan0: deauthenticated
> Oct 31 01:23:53 amd kernel: wlan0: authenticate with AP
> 00:11:2f:0e:95:a0
> Oct 31 01:23:53 amd kernel: wlan0: RX authentication from
> 00:11:2f:0e:95:a0 (alg=0 transaction=2 status=0)
> Oct 31 01:23:53 amd kernel: wlan0: authenticated
> Oct 31 01:23:53 amd kernel: wlan0: associate with AP 00:11:2f:0e:95:a0
> Oct 31 01:23:53 amd kernel: wlan0: RX ReassocResp from
> 00:11:2f:0e:95:a0 (capab=0x401 status=0 aid=1)
> Oct 31 01:23:53 amd kernel: wlan0: associated
> Oct 31 01:23:53 amd kernel: wlan0: switched to short barker preamble
> (BSSID=00:11:2f:0e:95:a0)
> Oct 31 01:23:53 amd kernel: iwl3945: iwl-3945-rs not selected as rate
> control algo!
> Oct 31 01:23:53 amd kernel: wlan0: CTS protection enabled
> (BSSID=00:11:2f:0e:95:a0)
> Oct 31 01:23:53 amd kernel: wlan0: switched to long barker preamble
> (BSSID=00:11:2f:0e:95:a0)
> Oct 31 01:35:44 amd -- MARK --
> Oct 31 01:38:16 amd kernel: iwl3945: Microcode SW error detected.
> Restarting 0x82000008.
> Oct 31 01:38:16 amd kernel: iwl3945: Error Reply type 0x00000005 cmd
> REPLY_TX (0x1C) seq 0x0267 ser 0x0000004B
> Oct 31 01:38:18 amd kernel: iwl3945: Can't stop Rx DMA.
>
> ...unfortunately, microcode sources are not available so Intel should
> fix this, right?
>
> (Actually, it recovered after 3 minutes):
>
> Oct 31 01:41:15 amd kernel: wlan0: RX deauthentication from
> 00:11:2f:0e:95:a0 (reason=4)
> Oct 31 01:41:15 amd kernel: wlan0: deauthenticated
> Oct 31 01:41:16 amd kernel: wlan0: authenticate with AP
> 00:11:2f:0e:95:a0
> Oct 31 01:41:16 amd kernel: wlan0: RX authentication from
> 00:11:2f:0e:95:a0 (alg=0 transaction=2 status=0)
> Oct 31 01:41:16 amd kernel: wlan0: authenticated
> Oct 31 01:41:16 amd kernel: wlan0: associate with AP 00:11:2f:0e:95:a0
> Oct 31 01:41:16 amd kernel: wlan0: RX ReassocResp from
> 00:11:2f:0e:95:a0 (capab=0x401 status=0 aid=1)
> Oct 31 01:41:16 amd kernel: wlan0: associated
> Oct 31 01:41:16 amd kernel: wlan0: CTS protection enabled
> (BSSID=00:11:2f:0e:95:a0)
> Oct 31 01:41:16 amd kernel: iwl3945: iwl-3945-rs not selected as rate
> control algo!
> Oct 31 01:41:16 amd kernel: wlan0: switched to short barker preamble
> (BSSID=00:11:2f:0e:95:a0)
>
> Hmm, and it is pretty reproducible, with:
>
> tcpspray -n 1 -b 10000000 10.0.0.2
>
> Oct 31 01:42:56 amd kernel: iwl3945: Microcode SW error detected.
> Restarting 0x82000008.
> Oct 31 01:42:56 amd kernel: iwl3945: Error Reply type 0x00000005 cmd
> REPLY_TX (0x1C) seq 0x02C7 ser 0x0000004B
> Oct 31 01:42:58 amd kernel: iwl3945: Can't stop Rx DMA.
next prev parent reply other threads:[~2007-11-01 1:42 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-10-31 0:52 iwl3945 in 2.6.24-rc1 dies under load Pavel Machek
2007-10-31 0:54 ` Zhu Yi
2007-10-31 11:05 ` Pavel Machek
2007-10-31 12:01 ` [ipw3945-devel] " Pablo Sanchez
2007-11-01 0:12 ` Pavel Machek
2007-11-01 1:37 ` Zhu Yi
2007-11-01 5:52 ` [ipw3945-devel] " mabbas
2007-11-03 18:34 ` Pavel Machek
2007-11-04 10:28 ` [ipw3945-devel] " drago01
2007-10-31 0:59 ` dragoran
2007-11-01 1:59 ` Rafael J. Wysocki [this message]
2007-11-01 8:22 ` Rolf Eike Beer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200711010259.05315.rjw@sisk.pl \
--to=rjw@sisk.pl \
--cc=ipw3945-devel@lists.sourceforge.net \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-wireless@vger.kernel.org \
--cc=pavel@ucw.cz \
--cc=yi.zhu@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).