From: "W. van den Akker" <listsrv@wilsoft.nl>
To: linux-wireless@vger.kernel.org
Subject: Re: Still problems to get ath9k in accessmode. Kernel hangs
Date: Tue, 6 Jan 2009 23:42:22 +0100 [thread overview]
Message-ID: <200901062342.22935.listsrv@wilsoft.nl> (raw)
In-Reply-To: <4963C43D.1080209@erley.org>
On Tuesday 06 January 2009 21:51:09 you wrote:
> W. van den Akker wrote:
> --- Snip ---
>
> >> However, after starting a internet session and Kmail session the server
> >> hangs again without any output. Does the NMI-handler not process per
> >> CPU? So if one CPU hangs, the other would still proceed?
> >>
> >> I have no 802.11n enabled, nor X.
> >>
> >> This means I think the system halted hard 'hlt-instruction'
> >>
> >> Any further suggestion? I am little bit hopeless now. I have placed the
> >> PCI card into another slot, no result.
> >
> > Some additional information:
> > I have booted the server at approx 16:00. Hostapd was started at
> > boot-time. After 5 hours without any connection from any computers the
> > server hangs.
>
> Just as a data point, I'm running master mode with ath9k on 64bit with
> multiple clients and have no problems. Perhaps it's hardware version
> related? Here's the info for my system:
>
> kernel: 2.6.28-gentoo
> compat-wireless-2.6: cedd75beb269e2b559a5174ee628ebd01f63a4040
> wireless-testing: fd1dae5fbc7a260b0ddfab7d4939a766a82ef3f3
> hostapd: 2c04820d80b5c489576cb735c3be8f026a035a5b
>
> I have 80211n enabled for my device with this config:
>
> ht_capab=[HT40-][SHORT-GI-40][DSSS_CCK-40]
>
> my device:
>
> Network controller: Atheros Communications, Inc. AR5416 802.11a/b/g/n
> Wireless PCI Adapter (rev 01)
>
> phy0: Atheros AR5416 MAC/BB Rev:2 AR2133 RF Rev:81:
> mem=0xffffc20000060000, irq=17
>
> Currently I'm using my ps3, axim, laptop, and a netbook at the same
> time, and have no disconnects. Any additional testing I could do that
> might help you out, or more information I could provide you?
My system:
kernel: 2.6.28-rc9-wl (wireless testing): 2.6.28-rc9-1-686-wl #1 SMP Fri Jan 2
19:38:20 CET 2009 i686 GNU/Linux
hostapd: 0.6.6
Have no 80211n enabled
Processor Intel(R) Pentium(R) 4 CPU 3.00GHz 1024 KB
my device:
04:08.0 Network controller: Atheros Communications Inc. AR5416 802.11abgn
Wireless PCI Adapter (rev 01)
Subsystem: Linksys Device 0061
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at d0310000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [40] #80 [0000]
Kernel driver in use: ath9k
Kernel modules: ath9k
System hangsup depending on the number of devices or cennections are opened:
- only hostapd (no devices connected). system hangs after approx 5 hours.
(ifconfig shows wlan0 up)
- only a laptop with a browsing session, system did nog hang after a few
hours.
- only a laptop with a browsing session and kmail, system hangs directly.
No logging to console. Nmi watchdog enabled...
--
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.
next prev parent reply other threads:[~2009-01-06 22:42 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-01-01 13:44 Still problems to get ath9k in accessmode. Kernel hangs W. van den Akker
2009-01-03 13:56 ` W. van den Akker
2009-01-05 9:41 ` Jouni Malinen
2009-01-06 7:57 ` W. van den Akker
2009-01-06 14:52 ` W. van den Akker
2009-01-06 20:32 ` W. van den Akker
2009-01-06 20:51 ` pat-lkml
2009-01-06 22:42 ` W. van den Akker [this message]
2009-01-07 15:42 ` W. van den Akker
2009-01-10 11:26 ` W. van den Akker
2009-01-10 19:50 ` pat-lkml
2009-01-12 7:47 ` W. van den Akker
-- strict thread matches above, loose matches on Subject: below --
2008-12-24 9:40 W. van den Akker
2008-12-24 10:07 ` Jouni Malinen
2008-12-24 17:45 ` Luis R. Rodriguez
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200901062342.22935.listsrv@wilsoft.nl \
--to=listsrv@wilsoft.nl \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).