From: Bruno Randolf <br1@einfach.org>
To: linville@tuxdriver.com
Cc: ath5k-devel@lists.ath5k.org, linux-wireless@vger.kernel.org
Subject: [PATCH v2 19/20] ath5k: new function for setting the antenna switch table
Date: Wed, 19 May 2010 10:32:19 +0900 [thread overview]
Message-ID: <20100519013219.22206.95141.stgit@tt-desk> (raw)
In-Reply-To: <20100519012528.22206.77550.stgit@tt-desk>
Collect all pieces concering the antenna switch table into one function.
Previously it was split up between ath5k_hw_reset() and
ath5k_hw_commit_eeprom_settings().
Also we need to set the antenna switch table when ath5k_hw_set_antenna_mode()
is called manually (by "iw phy0 antenna set", for example).
I'm not sure if we need to set the switchtable at the same place in
ath5k_hw_reset() as it was before - it is set later thru
ath5k_hw_set_antenna_mode() anyways - but i leave it there to avoid
problems(?).
Plus print switchtable registers in the debugfs file.
Signed-off-by: Bruno Randolf <br1@einfach.org>
---
drivers/net/wireless/ath/ath5k/ath5k.h | 1 +
drivers/net/wireless/ath/ath5k/debug.c | 7 +++++++
drivers/net/wireless/ath/ath5k/phy.c | 32 +++++++++++++++++++++++++++++++
drivers/net/wireless/ath/ath5k/reset.c | 33 ++++++--------------------------
4 files changed, 46 insertions(+), 27 deletions(-)
diff --git a/drivers/net/wireless/ath/ath5k/ath5k.h b/drivers/net/wireless/ath/ath5k/ath5k.h
index eace74d..cf16318 100644
--- a/drivers/net/wireless/ath/ath5k/ath5k.h
+++ b/drivers/net/wireless/ath/ath5k/ath5k.h
@@ -1286,6 +1286,7 @@ u16 ath5k_hw_radio_revision(struct ath5k_hw *ah, unsigned int chan);
int ath5k_hw_phy_disable(struct ath5k_hw *ah);
/* Antenna control */
void ath5k_hw_set_antenna_mode(struct ath5k_hw *ah, u8 ant_mode);
+void ath5k_hw_set_antenna_switch(struct ath5k_hw *ah, u8 ee_mode);
/* TX power setup */
int ath5k_hw_txpower(struct ath5k_hw *ah, struct ieee80211_channel *channel,
u8 ee_mode, u8 txpower);
diff --git a/drivers/net/wireless/ath/ath5k/debug.c b/drivers/net/wireless/ath/ath5k/debug.c
index d178d63..f3612e5 100644
--- a/drivers/net/wireless/ath/ath5k/debug.c
+++ b/drivers/net/wireless/ath/ath5k/debug.c
@@ -425,6 +425,13 @@ static ssize_t read_file_antenna(struct file *file, char __user *user_buf,
"AR5K_PHY_FAST_ANT_DIV_EN\t%d\n",
(v & AR5K_PHY_FAST_ANT_DIV_EN) != 0);
+ v = ath5k_hw_reg_read(sc->ah, AR5K_PHY_ANT_SWITCH_TABLE_0);
+ len += snprintf(buf+len, sizeof(buf)-len,
+ "\nAR5K_PHY_ANT_SWITCH_TABLE_0\t0x%08x\n", v);
+ v = ath5k_hw_reg_read(sc->ah, AR5K_PHY_ANT_SWITCH_TABLE_1);
+ len += snprintf(buf+len, sizeof(buf)-len,
+ "AR5K_PHY_ANT_SWITCH_TABLE_1\t0x%08x\n", v);
+
return simple_read_from_buffer(user_buf, count, ppos, buf, len);
}
diff --git a/drivers/net/wireless/ath/ath5k/phy.c b/drivers/net/wireless/ath/ath5k/phy.c
index 2136930..82720fc 100644
--- a/drivers/net/wireless/ath/ath5k/phy.c
+++ b/drivers/net/wireless/ath/ath5k/phy.c
@@ -1781,6 +1781,37 @@ ath5k_hw_set_fast_div(struct ath5k_hw *ah, u8 ee_mode, bool enable)
}
}
+void
+ath5k_hw_set_antenna_switch(struct ath5k_hw *ah, u8 ee_mode)
+{
+ u8 ant0, ant1;
+
+ /*
+ * In case a fixed antenna was set as default
+ * use the same switch table twice.
+ */
+ if (ah->ah_ant_mode == AR5K_ANTMODE_FIXED_A)
+ ant0 = ant1 = AR5K_ANT_SWTABLE_A;
+ else if (ah->ah_ant_mode == AR5K_ANTMODE_FIXED_B)
+ ant0 = ant1 = AR5K_ANT_SWTABLE_B;
+ else {
+ ant0 = AR5K_ANT_SWTABLE_A;
+ ant1 = AR5K_ANT_SWTABLE_B;
+ }
+
+ /* Set antenna idle switch table */
+ AR5K_REG_WRITE_BITS(ah, AR5K_PHY_ANT_CTL,
+ AR5K_PHY_ANT_CTL_SWTABLE_IDLE,
+ (ah->ah_ant_ctl[ee_mode][AR5K_ANT_CTL] |
+ AR5K_PHY_ANT_CTL_TXRX_EN));
+
+ /* Set antenna switch tables */
+ ath5k_hw_reg_write(ah, ah->ah_ant_ctl[ee_mode][ant0],
+ AR5K_PHY_ANT_SWITCH_TABLE_0);
+ ath5k_hw_reg_write(ah, ah->ah_ant_ctl[ee_mode][ant1],
+ AR5K_PHY_ANT_SWITCH_TABLE_1);
+}
+
/*
* Set antenna operating mode
*/
@@ -1900,6 +1931,7 @@ ath5k_hw_set_antenna_mode(struct ath5k_hw *ah, u8 ant_mode)
if (sta_id1)
AR5K_REG_ENABLE_BITS(ah, AR5K_STA_ID1, sta_id1);
+ ath5k_hw_set_antenna_switch(ah, ee_mode);
/* Note: set diversity before default antenna
* because it won't work correctly */
ath5k_hw_set_fast_div(ah, ee_mode, fast_div);
diff --git a/drivers/net/wireless/ath/ath5k/reset.c b/drivers/net/wireless/ath/ath5k/reset.c
index b1d3239..cf8fd48 100644
--- a/drivers/net/wireless/ath/ath5k/reset.c
+++ b/drivers/net/wireless/ath/ath5k/reset.c
@@ -730,7 +730,7 @@ static void ath5k_hw_tweak_initval_settings(struct ath5k_hw *ah,
}
static void ath5k_hw_commit_eeprom_settings(struct ath5k_hw *ah,
- struct ieee80211_channel *channel, u8 *ant, u8 ee_mode)
+ struct ieee80211_channel *channel, u8 ee_mode)
{
struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom;
s16 cck_ofdm_pwr_delta;
@@ -764,17 +764,9 @@ static void ath5k_hw_commit_eeprom_settings(struct ath5k_hw *ah,
ee->ee_cck_ofdm_gain_delta;
}
- /* Set antenna idle switch table */
- AR5K_REG_WRITE_BITS(ah, AR5K_PHY_ANT_CTL,
- AR5K_PHY_ANT_CTL_SWTABLE_IDLE,
- (ah->ah_ant_ctl[ee_mode][0] |
- AR5K_PHY_ANT_CTL_TXRX_EN));
-
- /* Set antenna switch tables */
- ath5k_hw_reg_write(ah, ah->ah_ant_ctl[ee_mode][ant[0]],
- AR5K_PHY_ANT_SWITCH_TABLE_0);
- ath5k_hw_reg_write(ah, ah->ah_ant_ctl[ee_mode][ant[1]],
- AR5K_PHY_ANT_SWITCH_TABLE_1);
+ /* XXX: necessary here? is called from ath5k_hw_set_antenna_mode()
+ * too */
+ ath5k_hw_set_antenna_switch(ah, ee_mode);
/* Noise floor threshold */
ath5k_hw_reg_write(ah,
@@ -890,7 +882,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,
struct ath_common *common = ath5k_hw_common(ah);
u32 s_seq[10], s_ant, s_led[3], staid1_flags, tsf_up, tsf_lo;
u32 phy_tst1;
- u8 mode, freq, ee_mode, ant[2];
+ u8 mode, freq, ee_mode;
int i, ret;
s_ant = 0;
@@ -1113,21 +1105,8 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,
AR5K_TXCFG_B_MODE);
}
- /*
- * In case a fixed antenna was set as default
- * use the same switch table twice.
- */
- if (ah->ah_ant_mode == AR5K_ANTMODE_FIXED_A)
- ant[0] = ant[1] = AR5K_ANT_SWTABLE_A;
- else if (ah->ah_ant_mode == AR5K_ANTMODE_FIXED_B)
- ant[0] = ant[1] = AR5K_ANT_SWTABLE_B;
- else {
- ant[0] = AR5K_ANT_SWTABLE_A;
- ant[1] = AR5K_ANT_SWTABLE_B;
- }
-
/* Commit values from EEPROM */
- ath5k_hw_commit_eeprom_settings(ah, channel, ant, ee_mode);
+ ath5k_hw_commit_eeprom_settings(ah, channel, ee_mode);
} else {
/*
next prev parent reply other threads:[~2010-05-19 1:33 UTC|newest]
Thread overview: 54+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-05-19 1:30 [PATCH v2 00/20] pending ath5k + antenna patches Bruno Randolf
2010-05-19 1:30 ` [PATCH v2 01/20] ath5k: add debugfs file for queue debugging Bruno Randolf
2010-05-19 1:30 ` [PATCH v2 02/20] ath5k: wake queues on reset Bruno Randolf
2010-05-20 12:51 ` [ath5k-devel] " Nick Kossifidis
2010-05-19 1:30 ` [PATCH v2 03/20] ath5k: initialize calibration timers Bruno Randolf
2010-05-20 12:48 ` Nick Kossifidis
2010-05-19 1:31 ` [PATCH v2 04/20] ath5k: move noise floor calibration into tasklet Bruno Randolf
2010-05-20 12:50 ` Nick Kossifidis
2010-05-19 1:31 ` [PATCH v2 05/20] ath5k: Stop queues only for NF calibration Bruno Randolf
2010-05-20 12:52 ` Nick Kossifidis
2010-05-19 1:31 ` [PATCH v2 06/20] ath5k: run NF calibration only every 60 seconds Bruno Randolf
2010-05-19 1:31 ` [PATCH v2 07/20] ath5k: remove ATH_TRACE macro Bruno Randolf
2010-05-20 12:56 ` Nick Kossifidis
2010-05-19 1:31 ` [PATCH v2 08/20] ath5k: clarify logic when to enable spur mitigation filter Bruno Randolf
2010-05-19 1:31 ` [PATCH v2 09/20] ath5k: use ath5k_softc as driver data Bruno Randolf
2010-05-19 1:31 ` [PATCH v2 10/20] ath5k: add sysfs files for ANI parameters Bruno Randolf
2010-05-20 12:58 ` Nick Kossifidis
2010-05-19 1:31 ` [PATCH v2 11/20] ath5k: always calculate ANI listen time Bruno Randolf
2010-05-20 12:59 ` Nick Kossifidis
2010-05-19 1:31 ` [PATCH v2 12/20] ath5k: print error message if ANI levels are out of range Bruno Randolf
2010-05-19 1:31 ` [PATCH v2 13/20] cfg80211: Add nl80211 antenna configuration Bruno Randolf
2010-05-19 17:07 ` Luis R. Rodriguez
2010-05-20 0:35 ` Bruno Randolf
2010-05-20 0:51 ` [ath5k-devel] " Luis R. Rodriguez
2010-05-20 1:12 ` Bruno Randolf
2010-05-20 1:26 ` Luis R. Rodriguez
2010-05-20 2:21 ` Bruno Randolf
2010-05-20 5:17 ` Luis R. Rodriguez
2010-05-20 5:36 ` Bruno Randolf
2010-05-20 6:43 ` Luis R. Rodriguez
2010-05-20 22:02 ` David Quan
2010-05-20 22:05 ` Luis R. Rodriguez
2010-05-20 22:14 ` Sam Ng
2010-05-20 22:24 ` Luis R. Rodriguez
2010-05-21 1:59 ` Bruno Randolf
2010-05-21 17:11 ` Luis R. Rodriguez
2010-05-21 19:10 ` Felix Fietkau
2010-05-21 20:28 ` Luis R. Rodriguez
2010-05-24 0:45 ` Bruno Randolf
2010-05-24 9:15 ` RHS Linux User
2010-06-04 19:30 ` John W. Linville
2010-06-04 21:21 ` [ath5k-devel] " Luis R. Rodriguez
2010-06-04 21:53 ` Luis R. Rodriguez
2010-06-07 3:45 ` Bruno Randolf
2010-05-19 1:31 ` [PATCH v2 14/20] mac80211: Add " Bruno Randolf
2010-05-19 1:31 ` [PATCH v2 15/20] ath5k: Add support for " Bruno Randolf
2010-05-19 1:32 ` [PATCH v2 16/20] ath5k: remove setting ANI and antenna thru debugfs files Bruno Randolf
2010-05-19 1:32 ` [PATCH v2 17/20] ath5k: fix NULL pointer in antenna configuration Bruno Randolf
2010-05-19 1:32 ` [PATCH v2 18/20] ath5k: update AR5K_PHY_RESTART_DIV_GC values to match masks Bruno Randolf
2010-05-20 12:54 ` Nick Kossifidis
2010-05-19 1:32 ` Bruno Randolf [this message]
2010-05-19 1:32 ` [PATCH v2 20/20] ath5k: no need to save/restore the default antenna Bruno Randolf
2010-05-19 1:41 ` [PATCH v2 00/20] pending ath5k + antenna patches Luis R. Rodriguez
2010-05-19 12:59 ` John W. Linville
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20100519013219.22206.95141.stgit@tt-desk \
--to=br1@einfach.org \
--cc=ath5k-devel@lists.ath5k.org \
--cc=linux-wireless@vger.kernel.org \
--cc=linville@tuxdriver.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).