From: Johannes Berg <johannes@sipsolutions.net>
To: John Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org, Johannes Berg <johannes.berg@intel.com>
Subject: [PATCH 4/6] mac80211: split out concurrent vif checks
Date: Fri, 27 Aug 2010 12:35:57 +0200 [thread overview]
Message-ID: <20100827103658.545080439@sipsolutions.net> (raw)
In-Reply-To: 20100827103553.559128239@sipsolutions.net
From: Johannes Berg <johannes.berg@intel.com>
Split the concurrent virtual interface checks
into a new function that can be used to check
for any given new interface type.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
---
net/mac80211/iface.c | 43 +++++++++++++++++++++++++++++--------------
1 file changed, 29 insertions(+), 14 deletions(-)
--- wireless-testing.orig/net/mac80211/iface.c 2010-08-26 16:00:31.000000000 +0200
+++ wireless-testing/net/mac80211/iface.c 2010-08-26 16:00:31.000000000 +0200
@@ -94,20 +94,14 @@ static inline int identical_mac_addr_all
type2 == NL80211_IFTYPE_AP_VLAN));
}
-static int ieee80211_open(struct net_device *dev)
+static int ieee80211_check_concurrent_iface(struct ieee80211_sub_if_data *sdata,
+ enum nl80211_iftype iftype)
{
- struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev);
- struct ieee80211_sub_if_data *nsdata;
struct ieee80211_local *local = sdata->local;
- struct sta_info *sta;
- u32 changed = 0;
- int res;
- u32 hw_reconf_flags = 0;
+ struct ieee80211_sub_if_data *nsdata;
+ struct net_device *dev = sdata->dev;
- /* fail early if user set an invalid address */
- if (!is_zero_ether_addr(dev->dev_addr) &&
- !is_valid_ether_addr(dev->dev_addr))
- return -EADDRNOTAVAIL;
+ ASSERT_RTNL();
/* we hold the RTNL here so can safely walk the list */
list_for_each_entry(nsdata, &local->interfaces, list) {
@@ -124,7 +118,7 @@ static int ieee80211_open(struct net_dev
* belonging to the same hardware. Then, however, we're
* faced with having to adopt two different TSF timers...
*/
- if (sdata->vif.type == NL80211_IFTYPE_ADHOC &&
+ if (iftype == NL80211_IFTYPE_ADHOC &&
nsdata->vif.type == NL80211_IFTYPE_ADHOC)
return -EBUSY;
@@ -138,19 +132,40 @@ static int ieee80211_open(struct net_dev
/*
* check whether it may have the same address
*/
- if (!identical_mac_addr_allowed(sdata->vif.type,
+ if (!identical_mac_addr_allowed(iftype,
nsdata->vif.type))
return -ENOTUNIQ;
/*
* can only add VLANs to enabled APs
*/
- if (sdata->vif.type == NL80211_IFTYPE_AP_VLAN &&
+ if (iftype == NL80211_IFTYPE_AP_VLAN &&
nsdata->vif.type == NL80211_IFTYPE_AP)
sdata->bss = &nsdata->u.ap;
}
}
+ return 0;
+}
+
+static int ieee80211_open(struct net_device *dev)
+{
+ struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+ struct ieee80211_local *local = sdata->local;
+ struct sta_info *sta;
+ u32 changed = 0;
+ int res;
+ u32 hw_reconf_flags = 0;
+
+ /* fail early if user set an invalid address */
+ if (!is_zero_ether_addr(dev->dev_addr) &&
+ !is_valid_ether_addr(dev->dev_addr))
+ return -EADDRNOTAVAIL;
+
+ res = ieee80211_check_concurrent_iface(sdata, sdata->vif.type);
+ if (res)
+ return res;
+
switch (sdata->vif.type) {
case NL80211_IFTYPE_WDS:
if (!is_valid_ether_addr(sdata->u.wds.remote_addr))
next prev parent reply other threads:[~2010-08-27 10:37 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-08-27 10:35 [PATCH 0/6] interface type switching while up Johannes Berg
2010-08-27 10:35 ` [PATCH 1/6] mac80211: clean up ifdown/cleanup paths Johannes Berg
2010-08-27 10:35 ` [PATCH 2/6] mac80211: switch to ieee80211_sdata_running Johannes Berg
2010-08-27 10:35 ` [PATCH 3/6] mac80211: simplify zero address checks Johannes Berg
2010-08-27 18:36 ` Gábor Stefanik
2010-08-27 19:24 ` Johannes Berg
2010-08-27 10:35 ` Johannes Berg [this message]
2010-08-27 10:35 ` [PATCH 5/6] mac80211: support runtime interface type changes Johannes Berg
2010-08-27 10:35 ` [PATCH 6/6] mac80211_hwsim: support runtime iftype changes Johannes Berg
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20100827103658.545080439@sipsolutions.net \
--to=johannes@sipsolutions.net \
--cc=johannes.berg@intel.com \
--cc=linux-wireless@vger.kernel.org \
--cc=linville@tuxdriver.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).