From: Christian Lamparter <chunkeey@googlemail.com>
To: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org,
"John W. Linville" <linville@tuxdriver.com>
Subject: [PATCH v2] mac80211: fix rx monitor filter refcounters
Date: Sat, 2 Oct 2010 13:17:07 +0200 [thread overview]
Message-ID: <201010021317.07864.chunkeey@googlemail.com> (raw)
In-Reply-To: <1286009187.1646.2.camel@Nokia-N900-51-1>
This patch fixes an refcounting bug. Previously it
was possible to corrupt the per-device recv. filter
and monitor management counters when:
iw dev wlanX set monitor [new flags]
was issued on an active monitor interface.
Acked-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
---
On Saturday 02 October 2010 10:46:27 Johannes Berg wrote:
> > + if (test_bit(SDATA_STATE_RUNNING, &sdata->state)) {
>
> There's an inline for this, I think?
>
> > static inline bool ieee80211_sdata_running(struct ieee80211_sub_if_data
>
> heh, by accident it's even in your patch :)
but what an accident!
---
diff --git a/net/mac80211/cfg.c b/net/mac80211/cfg.c
index c981604..9e63fc2 100644
--- a/net/mac80211/cfg.c
+++ b/net/mac80211/cfg.c
@@ -68,8 +68,36 @@ static int ieee80211_change_iface(struct wiphy *wiphy,
params && params->use_4addr >= 0)
sdata->u.mgd.use_4addr = params->use_4addr;
- if (sdata->vif.type == NL80211_IFTYPE_MONITOR && flags)
- sdata->u.mntr_flags = *flags;
+ if (sdata->vif.type == NL80211_IFTYPE_MONITOR && flags) {
+ struct ieee80211_local *local = sdata->local;
+
+ if (ieee80211_sdata_running(sdata)) {
+ /*
+ * Prohibit MONITOR_FLAG_COOK_FRAMES to be
+ * changed while the interface is up.
+ * Else we would need to add a lot of cruft
+ * to update everything:
+ * cooked_mntrs, monitor and all fif_* counters
+ * reconfigure hardware
+ */
+ if ((*flags & MONITOR_FLAG_COOK_FRAMES) !=
+ (sdata->u.mntr_flags & MONITOR_FLAG_COOK_FRAMES))
+ return -EBUSY;
+
+ ieee80211_adjust_monitor_flags(sdata, -1);
+ sdata->u.mntr_flags = *flags;
+ ieee80211_adjust_monitor_flags(sdata, 1);
+
+ ieee80211_configure_filter(local);
+ } else {
+ /*
+ * Because the interface is down, ieee80211_do_stop
+ * and ieee80211_do_open take care of "everything"
+ * mentioned in the comment above.
+ */
+ sdata->u.mntr_flags = *flags;
+ }
+ }
return 0;
}
diff --git a/net/mac80211/ieee80211_i.h b/net/mac80211/ieee80211_i.h
index 945fbf2..f6a6d78 100644
--- a/net/mac80211/ieee80211_i.h
+++ b/net/mac80211/ieee80211_i.h
@@ -1132,6 +1132,8 @@ void ieee80211_if_remove(struct ieee80211_sub_if_data *sdata);
void ieee80211_remove_interfaces(struct ieee80211_local *local);
u32 __ieee80211_recalc_idle(struct ieee80211_local *local);
void ieee80211_recalc_idle(struct ieee80211_local *local);
+void ieee80211_adjust_monitor_flags(struct ieee80211_sub_if_data *sdata,
+ const int offset);
static inline bool ieee80211_sdata_running(struct ieee80211_sub_if_data *sdata)
{
diff --git a/net/mac80211/iface.c b/net/mac80211/iface.c
index 6678573..1300e88 100644
--- a/net/mac80211/iface.c
+++ b/net/mac80211/iface.c
@@ -148,6 +148,26 @@ static int ieee80211_check_concurrent_iface(struct ieee80211_sub_if_data *sdata,
return 0;
}
+void ieee80211_adjust_monitor_flags(struct ieee80211_sub_if_data *sdata,
+ const int offset)
+{
+ struct ieee80211_local *local = sdata->local;
+ u32 flags = sdata->u.mntr_flags;
+
+#define ADJUST(_f, _s) do { \
+ if (flags & MONITOR_FLAG_##_f) \
+ local->fif_##_s += offset; \
+ } while (0)
+
+ ADJUST(FCSFAIL, fcsfail);
+ ADJUST(PLCPFAIL, plcpfail);
+ ADJUST(CONTROL, control);
+ ADJUST(CONTROL, pspoll);
+ ADJUST(OTHER_BSS, other_bss);
+
+#undef ADJUST
+}
+
/*
* NOTE: Be very careful when changing this function, it must NOT return
* an error on interface type changes that have been pre-checked, so most
@@ -240,17 +260,7 @@ static int ieee80211_do_open(struct net_device *dev, bool coming_up)
hw_reconf_flags |= IEEE80211_CONF_CHANGE_MONITOR;
}
- if (sdata->u.mntr_flags & MONITOR_FLAG_FCSFAIL)
- local->fif_fcsfail++;
- if (sdata->u.mntr_flags & MONITOR_FLAG_PLCPFAIL)
- local->fif_plcpfail++;
- if (sdata->u.mntr_flags & MONITOR_FLAG_CONTROL) {
- local->fif_control++;
- local->fif_pspoll++;
- }
- if (sdata->u.mntr_flags & MONITOR_FLAG_OTHER_BSS)
- local->fif_other_bss++;
-
+ ieee80211_adjust_monitor_flags(sdata, 1);
ieee80211_configure_filter(local);
netif_carrier_on(dev);
@@ -477,17 +487,7 @@ static void ieee80211_do_stop(struct ieee80211_sub_if_data *sdata,
hw_reconf_flags |= IEEE80211_CONF_CHANGE_MONITOR;
}
- if (sdata->u.mntr_flags & MONITOR_FLAG_FCSFAIL)
- local->fif_fcsfail--;
- if (sdata->u.mntr_flags & MONITOR_FLAG_PLCPFAIL)
- local->fif_plcpfail--;
- if (sdata->u.mntr_flags & MONITOR_FLAG_CONTROL) {
- local->fif_pspoll--;
- local->fif_control--;
- }
- if (sdata->u.mntr_flags & MONITOR_FLAG_OTHER_BSS)
- local->fif_other_bss--;
-
+ ieee80211_adjust_monitor_flags(sdata, -1);
ieee80211_configure_filter(local);
break;
case NL80211_IFTYPE_MESH_POINT:
prev parent reply other threads:[~2010-10-02 11:17 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-09-28 16:36 [RFC] mac80211: fix rx monitor filter refcounters Christian Lamparter
2010-09-29 7:10 ` Johannes Berg
2010-09-29 19:57 ` [RFC v2] " Christian Lamparter
2010-09-29 20:00 ` Johannes Berg
2010-10-01 21:53 ` [PATCH] " Christian Lamparter
2010-10-02 8:46 ` Johannes Berg
2010-10-02 11:17 ` Christian Lamparter [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=201010021317.07864.chunkeey@googlemail.com \
--to=chunkeey@googlemail.com \
--cc=johannes@sipsolutions.net \
--cc=linux-wireless@vger.kernel.org \
--cc=linville@tuxdriver.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).