* [PATCH 1/2] rt2x00: Fix radio off hang issue for PCIE interface
@ 2011-01-10 10:27 Ivo van Doorn
2011-01-10 10:28 ` [PATCH 2/2] rt2x00: Fix and fine-tune rf registers for RT3070/RT3071/RT3090 Ivo van Doorn
0 siblings, 1 reply; 2+ messages in thread
From: Ivo van Doorn @ 2011-01-10 10:27 UTC (permalink / raw)
To: John W. Linville; +Cc: linux-wireless, users
From: RA-Jay Hung <jay_hung@ralinktech.com>
PCI/PCIE radio off behavior is different from SOC/USB.
They mainly use MCU command to disable DMA, TX/RX and enter power saving mode.
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
---
drivers/net/wireless/rt2x00/rt2800lib.c | 6 -----
drivers/net/wireless/rt2x00/rt2800pci.c | 36 ++++++++----------------------
2 files changed, 10 insertions(+), 32 deletions(-)
diff --git a/drivers/net/wireless/rt2x00/rt2800lib.c b/drivers/net/wireless/rt2x00/rt2800lib.c
index 54917a2..e2a528d 100644
--- a/drivers/net/wireless/rt2x00/rt2800lib.c
+++ b/drivers/net/wireless/rt2x00/rt2800lib.c
@@ -2810,10 +2810,7 @@ void rt2800_disable_radio(struct rt2x00_dev *rt2x00dev)
rt2800_register_read(rt2x00dev, WPDMA_GLO_CFG, ®);
rt2x00_set_field32(®, WPDMA_GLO_CFG_ENABLE_TX_DMA, 0);
- rt2x00_set_field32(®, WPDMA_GLO_CFG_TX_DMA_BUSY, 0);
rt2x00_set_field32(®, WPDMA_GLO_CFG_ENABLE_RX_DMA, 0);
- rt2x00_set_field32(®, WPDMA_GLO_CFG_RX_DMA_BUSY, 0);
- rt2x00_set_field32(®, WPDMA_GLO_CFG_TX_WRITEBACK_DONE, 1);
rt2800_register_write(rt2x00dev, WPDMA_GLO_CFG, reg);
/* Wait for DMA, ignore error */
@@ -2823,9 +2820,6 @@ void rt2800_disable_radio(struct rt2x00_dev *rt2x00dev)
rt2x00_set_field32(®, MAC_SYS_CTRL_ENABLE_TX, 0);
rt2x00_set_field32(®, MAC_SYS_CTRL_ENABLE_RX, 0);
rt2800_register_write(rt2x00dev, MAC_SYS_CTRL, reg);
-
- rt2800_register_write(rt2x00dev, PWR_PIN_CFG, 0);
- rt2800_register_write(rt2x00dev, TX_PIN_CFG, 0);
}
EXPORT_SYMBOL_GPL(rt2800_disable_radio);
diff --git a/drivers/net/wireless/rt2x00/rt2800pci.c b/drivers/net/wireless/rt2x00/rt2800pci.c
index aa97971..bfc2fc5 100644
--- a/drivers/net/wireless/rt2x00/rt2800pci.c
+++ b/drivers/net/wireless/rt2x00/rt2800pci.c
@@ -475,39 +475,23 @@ static int rt2800pci_enable_radio(struct rt2x00_dev *rt2x00dev)
static void rt2800pci_disable_radio(struct rt2x00_dev *rt2x00dev)
{
- u32 reg;
-
- rt2800_disable_radio(rt2x00dev);
-
- rt2800_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00001280);
-
- rt2800_register_read(rt2x00dev, WPDMA_RST_IDX, ®);
- rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX0, 1);
- rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX1, 1);
- rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX2, 1);
- rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX3, 1);
- rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX4, 1);
- rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX5, 1);
- rt2x00_set_field32(®, WPDMA_RST_IDX_DRX_IDX0, 1);
- rt2800_register_write(rt2x00dev, WPDMA_RST_IDX, reg);
-
- rt2800_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00000e1f);
- rt2800_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00000e00);
+ if (rt2x00_is_soc(rt2x00dev)) {
+ rt2800_disable_radio(rt2x00dev);
+ rt2800_register_write(rt2x00dev, PWR_PIN_CFG, 0);
+ rt2800_register_write(rt2x00dev, TX_PIN_CFG, 0);
+ }
}
static int rt2800pci_set_state(struct rt2x00_dev *rt2x00dev,
enum dev_state state)
{
- /*
- * Always put the device to sleep (even when we intend to wakeup!)
- * if the device is booting and wasn't asleep it will return
- * failure when attempting to wakeup.
- */
- rt2800_mcu_request(rt2x00dev, MCU_SLEEP, 0xff, 0xff, 2);
-
if (state == STATE_AWAKE) {
- rt2800_mcu_request(rt2x00dev, MCU_WAKEUP, TOKEN_WAKUP, 0, 0);
+ rt2800_mcu_request(rt2x00dev, MCU_WAKEUP, TOKEN_WAKUP, 0, 0x02);
rt2800pci_mcu_status(rt2x00dev, TOKEN_WAKUP);
+ } else if (state == STATE_SLEEP) {
+ rt2800_register_write(rt2x00dev, H2M_MAILBOX_STATUS, 0xffffffff);
+ rt2800_register_write(rt2x00dev, H2M_MAILBOX_CID, 0xffffffff);
+ rt2800_mcu_request(rt2x00dev, MCU_SLEEP, 0x01, 0xff, 0x01);
}
return 0;
--
1.7.2.3
^ permalink raw reply related [flat|nested] 2+ messages in thread
* [PATCH 2/2] rt2x00: Fix and fine-tune rf registers for RT3070/RT3071/RT3090
2011-01-10 10:27 [PATCH 1/2] rt2x00: Fix radio off hang issue for PCIE interface Ivo van Doorn
@ 2011-01-10 10:28 ` Ivo van Doorn
0 siblings, 0 replies; 2+ messages in thread
From: Ivo van Doorn @ 2011-01-10 10:28 UTC (permalink / raw)
To: John W. Linville; +Cc: linux-wireless, users
From: RA-Jay Hung <jay_hung@ralinktech.com>
Basically fix and fine-tune RT3070/RT3071/RT3090 chip RF initial value
when call rt2800_init_rfcsr
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
---
drivers/net/wireless/rt2x00/rt2800.h | 6 ++++++
drivers/net/wireless/rt2x00/rt2800lib.c | 25 +++++++++++++++++--------
2 files changed, 23 insertions(+), 8 deletions(-)
diff --git a/drivers/net/wireless/rt2x00/rt2800.h b/drivers/net/wireless/rt2x00/rt2800.h
index 4c55e85..c7e615c 100644
--- a/drivers/net/wireless/rt2x00/rt2800.h
+++ b/drivers/net/wireless/rt2x00/rt2800.h
@@ -1805,6 +1805,12 @@ struct mac_iveiv_entry {
#define RFCSR30_RF_CALIBRATION FIELD8(0x80)
/*
+ * RFCSR 31:
+ */
+#define RFCSR31_RX_AGC_FC FIELD8(0x1f)
+#define RFCSR31_RX_H20M FIELD8(0x20)
+
+/*
* RF registers
*/
diff --git a/drivers/net/wireless/rt2x00/rt2800lib.c b/drivers/net/wireless/rt2x00/rt2800lib.c
index e2a528d..a25be62 100644
--- a/drivers/net/wireless/rt2x00/rt2800lib.c
+++ b/drivers/net/wireless/rt2x00/rt2800lib.c
@@ -2436,6 +2436,10 @@ static u8 rt2800_init_rx_filter(struct rt2x00_dev *rt2x00dev,
rt2x00_set_field8(&bbp, BBP4_BANDWIDTH, 2 * bw40);
rt2800_bbp_write(rt2x00dev, 4, bbp);
+ rt2800_rfcsr_read(rt2x00dev, 31, &rfcsr);
+ rt2x00_set_field8(&rfcsr, RFCSR31_RX_H20M, bw40);
+ rt2800_rfcsr_write(rt2x00dev, 31, rfcsr);
+
rt2800_rfcsr_read(rt2x00dev, 22, &rfcsr);
rt2x00_set_field8(&rfcsr, RFCSR22_BASEBAND_LOOPBACK, 1);
rt2800_rfcsr_write(rt2x00dev, 22, rfcsr);
@@ -2510,7 +2514,7 @@ static int rt2800_init_rfcsr(struct rt2x00_dev *rt2x00dev)
rt2800_rfcsr_write(rt2x00dev, 4, 0x40);
rt2800_rfcsr_write(rt2x00dev, 5, 0x03);
rt2800_rfcsr_write(rt2x00dev, 6, 0x02);
- rt2800_rfcsr_write(rt2x00dev, 7, 0x70);
+ rt2800_rfcsr_write(rt2x00dev, 7, 0x60);
rt2800_rfcsr_write(rt2x00dev, 9, 0x0f);
rt2800_rfcsr_write(rt2x00dev, 10, 0x41);
rt2800_rfcsr_write(rt2x00dev, 11, 0x21);
@@ -2602,12 +2606,12 @@ static int rt2800_init_rfcsr(struct rt2x00_dev *rt2x00dev)
rt2800_register_write(rt2x00dev, LDO_CFG0, reg);
} else if (rt2x00_rt(rt2x00dev, RT3071) ||
rt2x00_rt(rt2x00dev, RT3090)) {
+ rt2800_rfcsr_write(rt2x00dev, 31, 0x14);
+
rt2800_rfcsr_read(rt2x00dev, 6, &rfcsr);
rt2x00_set_field8(&rfcsr, RFCSR6_R2, 1);
rt2800_rfcsr_write(rt2x00dev, 6, rfcsr);
- rt2800_rfcsr_write(rt2x00dev, 31, 0x14);
-
rt2800_register_read(rt2x00dev, LDO_CFG0, ®);
rt2x00_set_field32(®, LDO_CFG0_BGSEL, 1);
if (rt2x00_rt_rev_lt(rt2x00dev, RT3071, REV_RT3071E) ||
@@ -2619,6 +2623,10 @@ static int rt2800_init_rfcsr(struct rt2x00_dev *rt2x00dev)
rt2x00_set_field32(®, LDO_CFG0_LDO_CORE_VLEVEL, 0);
}
rt2800_register_write(rt2x00dev, LDO_CFG0, reg);
+
+ rt2800_register_read(rt2x00dev, GPIO_SWITCH, ®);
+ rt2x00_set_field32(®, GPIO_SWITCH_5, 0);
+ rt2800_register_write(rt2x00dev, GPIO_SWITCH, reg);
} else if (rt2x00_rt(rt2x00dev, RT3390)) {
rt2800_register_read(rt2x00dev, GPIO_SWITCH, ®);
rt2x00_set_field32(®, GPIO_SWITCH_5, 0);
@@ -2670,10 +2678,11 @@ static int rt2800_init_rfcsr(struct rt2x00_dev *rt2x00dev)
rt2800_rfcsr_read(rt2x00dev, 17, &rfcsr);
rt2x00_set_field8(&rfcsr, RFCSR17_TX_LO1_EN, 0);
- if (rt2x00_rt_rev_lt(rt2x00dev, RT3071, REV_RT3071E) ||
+ if (rt2x00_rt(rt2x00dev, RT3070) ||
+ rt2x00_rt_rev_lt(rt2x00dev, RT3071, REV_RT3071E) ||
rt2x00_rt_rev_lt(rt2x00dev, RT3090, REV_RT3090E) ||
rt2x00_rt_rev_lt(rt2x00dev, RT3390, REV_RT3390E)) {
- if (test_bit(CONFIG_EXTERNAL_LNA_BG, &rt2x00dev->flags))
+ if (!test_bit(CONFIG_EXTERNAL_LNA_BG, &rt2x00dev->flags))
rt2x00_set_field8(&rfcsr, RFCSR17_R, 1);
}
rt2x00_eeprom_read(rt2x00dev, EEPROM_TXMIXER_GAIN_BG, &eeprom);
@@ -2686,6 +2695,7 @@ static int rt2800_init_rfcsr(struct rt2x00_dev *rt2x00dev)
if (rt2x00_rt(rt2x00dev, RT3090)) {
rt2800_bbp_read(rt2x00dev, 138, &bbp);
+ /* Turn off unused DAC1 and ADC1 to reduce power consumption */
rt2x00_eeprom_read(rt2x00dev, EEPROM_NIC_CONF0, &eeprom);
if (rt2x00_get_field16(eeprom, EEPROM_NIC_CONF0_RXPATH) == 1)
rt2x00_set_field8(&bbp, BBP138_RX_ADC1, 0);
@@ -2719,10 +2729,9 @@ static int rt2800_init_rfcsr(struct rt2x00_dev *rt2x00dev)
rt2800_rfcsr_write(rt2x00dev, 21, rfcsr);
}
- if (rt2x00_rt(rt2x00dev, RT3070) || rt2x00_rt(rt2x00dev, RT3071)) {
+ if (rt2x00_rt(rt2x00dev, RT3070)) {
rt2800_rfcsr_read(rt2x00dev, 27, &rfcsr);
- if (rt2x00_rt_rev_lt(rt2x00dev, RT3070, REV_RT3070F) ||
- rt2x00_rt_rev_lt(rt2x00dev, RT3071, REV_RT3071E))
+ if (rt2x00_rt_rev_lt(rt2x00dev, RT3070, REV_RT3070F))
rt2x00_set_field8(&rfcsr, RFCSR27_R1, 3);
else
rt2x00_set_field8(&rfcsr, RFCSR27_R1, 0);
--
1.7.2.3
^ permalink raw reply related [flat|nested] 2+ messages in thread
end of thread, other threads:[~2011-01-10 10:28 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-01-10 10:27 [PATCH 1/2] rt2x00: Fix radio off hang issue for PCIE interface Ivo van Doorn
2011-01-10 10:28 ` [PATCH 2/2] rt2x00: Fix and fine-tune rf registers for RT3070/RT3071/RT3090 Ivo van Doorn
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).