From: Ali Bahar <ali@internetdog.org>
To: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Subject: r8712u driver for the rtl8192su chip.
Date: Tue, 21 Jun 2011 20:49:54 +0800 [thread overview]
Message-ID: <20110621124954.GA8462@internetdog.org> (raw)
In-Reply-To: <4DC06BF3.6070208@lwfinger.net>
Hi Larry,
this is more of a quick FYI, regarding Staging's r8712u driver.
On Tue, May 03, 2011 at 03:56:19PM -0500, Larry Finger wrote:
> On 05/03/2011 03:38 PM, Gábor Stefanik wrote:
> >2011/5/3 Larry Finger<Larry.Finger@lwfinger.net>:
> >>On 05/03/2011 03:19 PM, Gábor Stefanik wrote:
> code. The r8712u driver in staging is for the RTL8192SU, and it
> works perfectly well. It just doesn't use mac80211, which is why it
> needs to be replaced.
>
> Larry
I ran iwconfig on this device in order to put it into Monitor mode, or
even to change its ssid. Both failed because the Set ioctls were not
permitted.
Again, this is more of an FYI, since I don't really use this device.
regards,
ali
PS I did not CC the thread's original list of recipients, because this
tangents somewhat from its main topic.
PPS for the benefit of googlers: the device is the ASUS WL-167G V3
wireless USB adapter.
Additional Info:
~~~~~~~~~~~~~~~
root@hashbang Tue Jun 21 18:24:39 ~$ ifconfig wlan2
wlan2 Link encap:Ethernet HWaddr 48:5b:39:eb:d2:7c
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root@hashbang Tue Jun 21 18:24:57 ~$ iwconfig wlan2
wlan2 unassociated Nickname:"rtl_wifi"
Mode:Auto Access Point: Not-Associated Sensitivity:0/0
Retry:off RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
root@hashbang Tue Jun 21 18:25:02 ~$ ethtool -i wlan2
driver: r8712u
version:
firmware-version:
bus-info: 1-1:1.0
root@hashbang Tue Jun 21 18:25:09 ~$ lsusb|grep :1791
Bus 001 Device 002: ID 0b05:1791 ASUSTek Computer, Inc.
root@hashbang Tue Jun 21 18:28:48 ~$ iwconfig wlan2 mode Monitor
Error for wireless request "Set Mode" (8B06) :
SET failed on device wlan2 ; Invalid argument.
root@hashbang Tue Jun 21 18:30:06 ~$ iwconfig wlan2 essid "h55m"
Error for wireless request "Set ESSID" (8B1A) :
SET failed on device wlan2 ; Operation not permitted.
root@hashbang Tue Jun 21 18:30:47 ~$ uname -r
3.0.0-rc2-wl_m_Sat12jun2011
root@hashbang Tue Jun 21 18:36:57 ~$
root@hashbang Tue Jun 21 20:17:28 ~$ iwconfig wlan2
wlan2 unassociated Nickname:"rtl_wifi"
Mode:Auto Access Point: Not-Associated Sensitivity:0/0
Retry:off RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
root@hashbang Tue Jun 21 20:18:26 ~$ iwconfig wlan2 mode Managed
root@hashbang Tue Jun 21 20:18:37 ~$ iwconfig wlan2 essid "h55m"
channel 11
Error for wireless request "Set ESSID" (8B1A) :
SET failed on device wlan2 ; Operation not permitted.
root@hashbang Tue Jun 21 20:19:00 ~$ iwconfig wlan2
wlan2 unassociated Nickname:"rtl_wifi"
Mode:Managed Access Point: Not-Associated Sensitivity:0/0
Retry:off RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
root@hashbang Tue Jun 21 20:19:10 ~$
next prev parent reply other threads:[~2011-06-21 12:51 UTC|newest]
Thread overview: 40+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-05-03 14:47 [PATCH 00/12] rtlwifi: rtl8192se: Merge new driver Larry Finger
2011-05-03 15:01 ` Borislav Petkov
2011-05-03 20:03 ` Larry Finger
2011-05-04 17:01 ` Borislav Petkov
2011-05-04 17:20 ` Larry Finger
2011-05-04 18:06 ` Borislav Petkov
2011-05-04 19:15 ` Larry Finger
2011-05-03 15:59 ` Walter Goldens
2011-05-03 16:45 ` Larry Finger
2011-05-03 20:19 ` Gábor Stefanik
2011-05-03 20:33 ` Larry Finger
2011-05-03 20:38 ` Gábor Stefanik
2011-05-03 20:56 ` Larry Finger
2011-05-03 21:09 ` Gábor Stefanik
2011-05-03 21:35 ` Larry Finger
2011-06-21 12:49 ` Ali Bahar [this message]
2011-06-21 22:08 ` r8712u driver for the rtl8192su chip Larry Finger
2011-06-22 1:00 ` Ali Bahar
2011-06-22 2:03 ` Julian Calaby
2011-06-22 2:12 ` Gábor Stefanik
2011-06-22 2:46 ` Ali Bahar
2011-06-22 2:39 ` Ali Bahar
2011-06-22 2:34 ` Larry Finger
2011-06-22 2:56 ` Ali Bahar
2011-06-22 3:09 ` Larry Finger
2011-06-22 3:17 ` Ali Bahar
2011-06-27 7:23 ` Ali Bahar
2011-07-02 17:09 ` Larry Finger
2011-07-03 1:06 ` Ali Bahar
2011-07-03 1:24 ` Larry Finger
2011-07-03 1:47 ` Ali Bahar
2011-07-15 17:11 ` [PATCH 0/2] staging: r8712u: Most return-values changed from -1 to Ali Bahar
2011-07-15 17:11 ` [PATCH 1/2] staging: r8712u: Most return-values changed from -1 to proper errno macros Ali Bahar
2011-07-15 21:00 ` Larry Finger
2011-07-16 3:21 ` Ali Bahar
2011-07-16 9:23 ` Kalle Valo
2011-07-16 10:50 ` Ali Bahar
2011-07-16 11:44 ` Kalle Valo
2011-07-16 11:55 ` Ali Bahar
2011-07-15 17:11 ` [PATCH 2/2] staging: r8712u: checkpatch errors: trailing whitespace on 2 lines Ali Bahar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20110621124954.GA8462@internetdog.org \
--to=ali@internetdog.org \
--cc=Larry.Finger@lwfinger.net \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).