Re: [PATCH 1/2] ssb: define boardflags

["Michael Büsch" <m@bues.ch>]

On Sat, 23 Jul 2011 11:10:11 +0200
Rafał Miłecki <zajec5@gmail.com> wrote:

> They are SPROM specific, so all should be defined in ssb code.

Oh, well. I'm not sure.
Most of these currently are defined in b43 code, because they are b43-specific
and _not_ ssb specific. If we decide to define them in ssb, they need to be
removed from b43, at least.

> Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
> ---
>  include/linux/ssb/ssb_regs.h |   40 ++++++++++++++++++++++++++++++++++++++++
>  1 files changed, 40 insertions(+), 0 deletions(-)
> 
> diff --git a/include/linux/ssb/ssb_regs.h b/include/linux/ssb/ssb_regs.h
> index efbf459..9894120 100644
> --- a/include/linux/ssb/ssb_regs.h
> +++ b/include/linux/ssb/ssb_regs.h
> @@ -462,6 +462,46 @@
>  #define SSB_SPROM8_OFDM5GLPO		0x014A	/* 5.2GHz OFDM power offset */
>  #define SSB_SPROM8_OFDM5GHPO		0x014E	/* 5.8GHz OFDM power offset */
>  
> +/* Values for boardflags_lo read from SPROM */
> +#define SSB_BFL_BTCOEXIST		0x0001	/* implements Bluetooth coexistance */
> +#define SSB_BFL_PACTRL			0x0002	/* GPIO 9 controlling the PA */
> +#define SSB_BFL_AIRLINEMODE		0x0004	/* implements GPIO 13 radio disable indication */
> +#define SSB_BFL_RSSI			0x0008	/* software calculates nrssi slope. */
> +#define SSB_BFL_ENETSPI			0x0010	/* has ephy roboswitch spi */
> +#define SSB_BFL_XTAL_NOSLOW		0x0020	/* no slow clock available */
> +#define SSB_BFL_CCKHIPWR		0x0040	/* can do high power CCK transmission */
> +#define SSB_BFL_ENETADM			0x0080	/* has ADMtek switch */
> +#define SSB_BFL_ENETVLAN		0x0100	/* can do vlan */
> +#define SSB_BFL_AFTERBURNER		0x0200	/* supports Afterburner mode */
> +#define SSB_BFL_NOPCI			0x0400	/* board leaves PCI floating */
> +#define SSB_BFL_FEM			0x0800	/* supports the Front End Module */
> +#define SSB_BFL_EXTLNA			0x1000	/* has an external LNA */
> +#define SSB_BFL_HGPA			0x2000	/* had high gain PA */
> +#define SSB_BFL_BTCMOD			0x4000	/* BFL_BTCOEXIST is given in alternate GPIOs */
> +#define SSB_BFL_ALTIQ			0x8000	/* alternate I/Q settings */
> +
> +/* Values for boardflags_hi read from SPROM */
> +#define SSB_BFH_NOPA			0x0001	/* has no PA */
> +#define SSB_BFH_RSSIINV			0x0002	/* RSSI uses positive slope (not TSSI) */
> +#define SSB_BFH_PAREF			0x0004	/* uses the PARef LDO */
> +#define SSB_BFH_3TSWITCH		0x0008	/* uses a triple throw switch shared with bluetooth */
> +#define SSB_BFH_PHASESHIFT		0x0010	/* can support phase shifter */
> +#define SSB_BFH_BUCKBOOST		0x0020	/* has buck/booster */
> +#define SSB_BFH_FEM_BT			0x0040	/* has FEM and switch to share antenna with bluetooth */
> +
> +/* Values for boardflags2_lo read from SPROM */
> +#define SSB_BFL2_RXBB_INT_REG_DIS	0x0001	/* external RX BB regulator present */
> +#define SSB_BFL2_APLL_WAR		0x0002	/* alternative A-band PLL settings implemented */
> +#define SSB_BFL2_TXPWRCTRL_EN 		0x0004	/* permits enabling TX Power Control */
> +#define SSB_BFL2_2X4_DIV		0x0008	/* 2x4 diversity switch */
> +#define SSB_BFL2_5G_PWRGAIN		0x0010	/* supports 5G band power gain */
> +#define SSB_BFL2_PCIEWAR_OVR		0x0020	/* overrides ASPM and Clkreq settings */
> +#define SSB_BFL2_CAESERS_BRD		0x0040	/* is Caesers board (unused) */
> +#define SSB_BFL2_BTC3WIRE		0x0080	/* used 3-wire bluetooth coexist */
> +#define SSB_BFL2_SKWRKFEM_BRD		0x0100	/* 4321mcm93 uses Skyworks FEM */
> +#define SSB_BFL2_SPUR_WAR		0x0200	/* has a workaround for clock-harmonic spurs */
> +#define SSB_BFL2_GPLL_WAR		0x0400	/* altenative G-band PLL settings implemented */
> +
>  /* Values for SSB_SPROM1_BINF_CCODE */
>  enum {
>  	SSB_SPROM1CCODE_WORLD = 0,



-- 
Greetings, Michael.