From mboxrd@z Thu Jan 1 00:00:00 1970 Return-path: Received: from emh01.mail.saunalahti.fi ([62.142.5.107]:40527 "EHLO emh01.mail.saunalahti.fi" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1753149Ab2AQSJC (ORCPT ); Tue, 17 Jan 2012 13:09:02 -0500 Subject: [PATCH v3 3/8] ath6kl: add ATH6KL_CONF_UART_DEBUG To: kvalo@qca.qualcomm.com From: Kalle Valo Cc: ath6kl-devel@qualcomm.com, linux-wireless@vger.kernel.org Date: Tue, 17 Jan 2012 20:08:56 +0200 Message-ID: <20120117180856.29995.25607.stgit@localhost6.localdomain6> (sfid-20120117_190906_493022_01D68971) In-Reply-To: <20120117180827.29995.67922.stgit@localhost6.localdomain6> References: <20120117180827.29995.67922.stgit@localhost6.localdomain6> MIME-Version: 1.0 Content-Type: text/plain; charset="utf-8" Sender: linux-wireless-owner@vger.kernel.org List-ID: Add ATH6KL_CONF_UART_DEBUG which is set whenever uart_debug module parameter is enabled. This way we can keep the uart_debug parameter static when core.c file is introduced. Signed-off-by: Kalle Valo --- drivers/net/wireless/ath/ath6kl/core.h | 1 + drivers/net/wireless/ath/ath6kl/init.c | 5 ++++- 2 files changed, 5 insertions(+), 1 deletions(-) diff --git a/drivers/net/wireless/ath/ath6kl/core.h b/drivers/net/wireless/ath/ath6kl/core.h index a75c09e..5b48ed4 100644 --- a/drivers/net/wireless/ath/ath6kl/core.h +++ b/drivers/net/wireless/ath/ath6kl/core.h @@ -195,6 +195,7 @@ struct ath6kl_fw_ie { #define ATH6KL_CONF_ENABLE_11N BIT(2) #define ATH6KL_CONF_ENABLE_TX_BURST BIT(3) #define ATH6KL_CONF_SUSPEND_CUTPOWER BIT(4) +#define ATH6KL_CONF_UART_DEBUG BIT(5) enum wlan_low_pwr_state { WLAN_POWER_STATE_ON, diff --git a/drivers/net/wireless/ath/ath6kl/init.c b/drivers/net/wireless/ath/ath6kl/init.c index 6baa855..911e2df 100644 --- a/drivers/net/wireless/ath/ath6kl/init.c +++ b/drivers/net/wireless/ath/ath6kl/init.c @@ -466,7 +466,7 @@ int ath6kl_configure_target(struct ath6kl *ar) u8 fw_iftype, fw_mode = 0, fw_submode = 0; int i, status; - param = uart_debug; + param = !!(ar->conf_flags & ATH6KL_CONF_UART_DEBUG); if (ath6kl_bmi_write(ar, ath6kl_get_hi_item_addr(ar, HI_ITEM(hi_serial_enable)), (u8 *)¶m, 4)) { ath6kl_err("bmi_write_memory for uart debug failed\n"); @@ -1679,6 +1679,9 @@ int ath6kl_core_init(struct ath6kl *ar) if (suspend_cutpower) ar->conf_flags |= ATH6KL_CONF_SUSPEND_CUTPOWER; + if (uart_debug) + ar->conf_flags |= ATH6KL_CONF_UART_DEBUG; + ar->wiphy->flags |= WIPHY_FLAG_SUPPORTS_FW_ROAM | WIPHY_FLAG_HAVE_AP_SME | WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL |