From: Anisse Astier <anisse@astier.eu>
To: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org, 李朝明 <chaoming_li@realsil.com.cn>
Subject: Re: rtl8192ce: activation problem with rtl8188ce pci card
Date: Thu, 6 Sep 2012 10:01:29 +0200 [thread overview]
Message-ID: <20120906100129.56210d74@destiny.ordissimo> (raw)
In-Reply-To: <5047B508.5030606@lwfinger.net>
[-- Attachment #1: Type: text/plain, Size: 5280 bytes --]
Hi,
On Wed, 05 Sep 2012 15:24:40 -0500, Larry Finger <Larry.Finger@lwfinger.net> wrote :
> On 09/05/2012 01:14 PM, Anisse Astier wrote:
>
> The ID that counts is the first one. I think the second is some kind of vendor code.
Yes, it should be the id of the card instead of the chip. But it shows
that this module hasn't been lspci'd much in the wild.
>
> Note, the RTL8188CE-VL does not work with wireless-next, but does with
> wireless-testing with some patches applied. I will contact the Realtek software
> team to ask questions about your card. I added my contact as a Cc here. In the
> meantime, could you try the wireless-testing tree? If your card still does not
> work, I will send you some patches to see what it takes.
I have the same issue with wireless-testing. dmesg in attachment.
Logs:
[ 521.487043] cfg80211: Calling CRDA to update world regulatory domain
[ 521.590821] rtl8192ce: Using firmware rtlwifi/rtl8192cfw.bin
[ 521.632956] rtlwifi:rtl_fw_cb():<0-0> Firmware callback routine entered!
[ 521.697121] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
[ 521.703862] rtlwifi: wireless switch is on
[ 521.761161] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 521.761267] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 521.761415] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 521.761564] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 521.761712] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 521.761860] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 521.762008] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 521.762157] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:18051d59:11
[ 521.762305] rtl8192ce:_rtl92ce_init_mac():<0-0> reg0xec:98053f15:10
[ 521.763460] rtl8192c_common:rtl92c_download_fw():<0-0> Firmware Version(49), Signature(0x88c1),Size(32)
[ 521.984907] rtl8192ce:rtl92ce_enable_hw_security_config():<0-0> PairwiseEncAlgorithm = 0 GroupEncAlgorithm = 0
[ 521.984924] rtl8192ce:rtl92ce_enable_hw_security_config():<0-0> The SECR-value cc
[ 522.093885] rtl8192c_common:rtl92c_dm_initialize_txpower_tracking_thermalmeter():<0-0> pMgntInfo->txpower_tracking = 1
[ 522.093901] rtlwifi:rtl_pci_start():<0-0> enable_interrupt OK
[ 522.093909] rtlwifi:rtl_pci_start():<0-0> OK
[ 522.097066] rtl8192c_common:rtl92c_dm_dynamic_bb_powersaving():<0-0> Not connected to any
[ 522.097080] rtl8192c_common:rtl92c_dm_dynamic_bb_powersaving():<0-0> AP Ext Port PWDB = 0x0
[ 522.097140] rtl8192c_common:rtl92c_dm_check_txpower_tracking_thermal_meter():<0-0> Trigger 92S Thermal Meter!!
[ 522.106799] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 2
[ 522.106806] rtl8192ce:rtl92ce_sw_led_on():<0-0> LedAddr:4E ledpin=1
[ 522.106843] rtlwifi:rtl_op_bss_info_changed():<0-0> BSS_CHANGED_ERP_PREAMBLE use short preamble:0
[ 522.106852] rtl8192ce:rtl92ce_set_hw_reg():<0-0> HW_VAR_SLOT_TIME 14
[ 522.107898] rtlwifi:rtl_op_config():<0-0> IEEE80211_CONF_CHANGE_LISTEN_INTERVAL
[ 522.108197] rtlwifi:rtl_op_config():<0-0> IEEE80211_CONF_CHANGE_RETRY_LIMITS 4
[ 522.119643] rtl8192c_common:rtl92c_phy_sw_chnl():<0-0> sw_chnl_inprogress false schdule workitem
[ 522.119650] rtl8192ce:rtl92ce_set_hw_reg():<0-0> HW_VAR_SLOT_TIME 14
[ 522.135385] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 522.185258] rtl8192ce:rtl92ce_led_control():<10000-1> ledaction 5
[ 522.208511] rtl8192ce:_rtl92ce_phy_set_rf_power_state():<0-0> IPS Set eRf nic disable
[ 522.209007] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 2
[ 522.209018] rtl8192ce:rtl92ce_sw_led_on():<0-0> LedAddr:4E ledpin=1
[ 523.421145] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 523.421161] rtlwifi:_rtl_pci_interrupt():<10000-1> rx overflow !
[ 523.421891] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 523.421903] rtlwifi:_rtl_pci_interrupt():<10000-1> rx overflow !
[ 523.425246] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 523.425261] rtlwifi:_rtl_pci_interrupt():<10000-1> rx overflow !
[ 523.426638] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 523.426649] rtlwifi:_rtl_pci_interrupt():<10000-1> rx overflow !
[ 523.426991] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 523.426995] rtlwifi:_rtl_pci_interrupt():<10000-1> rx overflow !
[ 523.435796] rtlwifi:_rtl_pci_interrupt():<10000-1> rx descriptor unavailable!
[ 523.435811] rtlwifi:_rtl_pci_interrupt():<10000-1> rx overflow !
After removal:
[ 523.616579] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 2
[ 523.616596] rtl8192ce:rtl92ce_sw_led_on():<0-0> LedAddr:4E ledpin=1
[ 523.619524] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 2
[ 523.619538] rtl8192ce:rtl92ce_sw_led_on():<0-0> LedAddr:4E ledpin=1
[ 523.619549] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 7
[ 523.619559] rtl8192ce:rtl92ce_sw_led_off():<0-0> LedAddr:4E ledpin=1
[ 523.628275] rtl8192c_common:rtl92c_firmware_selfreset(): 8051 reset fail
[ 523.628296] rtl8192ce:rtl92ce_led_control():<0-0> ledaction 7
[ 523.628305] rtl8192ce:rtl92ce_sw_led_off():<0-0> LedAddr:4E ledpin=1
Also I noticed that during the initialization phase (rtlwifi/pci.c)
RT_TRACE doesn't print anything.
Anisse
[-- Attachment #2: dmesg-rtl8192ce-no-up-wireless-testing.txt.gz --]
[-- Type: application/x-gzip, Size: 14023 bytes --]
next prev parent reply other threads:[~2012-09-06 8:01 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-09-05 16:55 rtl8192ce: activation problem with rtl8188ce pci card Anisse Astier
2012-09-05 17:38 ` Larry Finger
2012-09-05 18:01 ` Anisse Astier
2012-09-05 18:14 ` Anisse Astier
2012-09-05 20:24 ` Larry Finger
2012-09-06 8:01 ` Anisse Astier [this message]
2012-09-06 14:15 ` Anisse Astier
[not found] ` <5048D138.1080109@lwfinger.net>
[not found] ` <20120906202710.30c4bc8a@destiny.ordissimo>
2012-09-06 19:04 ` Larry Finger
2012-09-07 8:44 ` Anisse Astier
2012-09-10 17:33 ` Anisse Astier
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20120906100129.56210d74@destiny.ordissimo \
--to=anisse@astier.eu \
--cc=Larry.Finger@lwfinger.net \
--cc=chaoming_li@realsil.com.cn \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox