* [3.7.0 regression] rt2x00lib_probe_dev: Error - Failed to initialize hw @ 2012-12-17 10:51 Mikael Pettersson 2012-12-17 11:10 ` devendra.aaru 2012-12-17 13:48 ` Stanislaw Gruszka 0 siblings, 2 replies; 9+ messages in thread From: Mikael Pettersson @ 2012-12-17 10:51 UTC (permalink / raw) To: linux-wireless; +Cc: linux-kernel I just updated an old 1st gen AMD64 laptop from kernel 3.6.0 to 3.7.0, Fedora 15 user-space, and was greeted by the following kernel warning: WARNING: at net/wireless/core.c:389 wiphy_register+0x5c3/0x600 [cfg80211]() Hardware name: SAM#451B Modules linked in: rt2500pci(+) snd_mpu401_uart rt2x00pci snd_rawmidi rt2x00lib sg snd_seq_device mac80211 cfg80211 amd64_agp agpgart snd eeprom_93cx6 soundcore via_rhine mii evdev ipv6 ehci_hcd uhci_hcd sr_mod cdrom usbcore usb_common Pid: 378, comm: modprobe Not tainted 3.7.0 #1 Call Trace: [<ffffffff810260b9>] ? warn_slowpath_common+0x79/0xc0 [<ffffffffa0115773>] ? wiphy_register+0x5c3/0x600 [cfg80211] [<ffffffff810c5b3f>] ? __kmalloc+0xef/0x170 [<ffffffffa013ac97>] ? ieee80211_register_hw+0x347/0x6d0 [mac80211] [<ffffffffa00f92ed>] ? rt2x00lib_probe_dev+0x53d/0x720 [rt2x00lib] [<ffffffffa0060888>] ? rt2x00pci_probe+0x168/0x2e4 [rt2x00pci] [<ffffffff81194cd0>] ? pci_device_probe+0xd0/0x170 [<ffffffff811f2934>] ? driver_probe_device+0x64/0x210 [<ffffffff811f2b73>] ? __driver_attach+0x93/0xa0 [<ffffffff811f2ae0>] ? driver_probe_device+0x210/0x210 [<ffffffff811f0f95>] ? bus_for_each_dev+0x45/0x80 [<ffffffff811f20d8>] ? bus_add_driver+0x178/0x250 [<ffffffff811f314e>] ? driver_register+0x6e/0x170 [<ffffffff81048a14>] ? notifier_call_chain+0x44/0x60 [<ffffffffa0196000>] ? 0xffffffffa0195fff [<ffffffff810002ca>] ? do_one_initcall+0x11a/0x160 [<ffffffff81069786>] ? sys_init_module+0x76/0x1c0 [<ffffffff812c15d0>] ? system_call_fastpath+0x16/0x1b ---[ end trace f8413f27de31929d ]--- phy0 -> rt2x00lib_probe_dev: Error - Failed to initialize hw. rt2500pci: probe of 0000:00:0c.0 failed with error -22 Rebooting into 3.6.0 shows no such error, booting 3.7.0 again shows the error, so it's completely reproducible. lspci -v for the device in question: 00:0c.0 Network controller: Ralink corp. RT2500 802.11g (rev 01) Subsystem: Micro-Star International Co., Ltd. Unknown 802.11g mini-PCI Adapter Flags: bus master, slow devsel, latency 64, IRQ 18 Memory at d0000000 (32-bit, non-prefetchable) [size=8K] Capabilities: [40] Power Management version 2 Kernel driver in use: rt2500pci Kernel modules: rt2500pci I've never actually used or configured this device (the laptop is always on wired ethernet), but thought you should know about this possible driver regression. /Mikael ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [3.7.0 regression] rt2x00lib_probe_dev: Error - Failed to initialize hw 2012-12-17 10:51 [3.7.0 regression] rt2x00lib_probe_dev: Error - Failed to initialize hw Mikael Pettersson @ 2012-12-17 11:10 ` devendra.aaru 2012-12-17 11:11 ` devendra.aaru 2012-12-17 12:22 ` Mikael Pettersson 2012-12-17 13:48 ` Stanislaw Gruszka 1 sibling, 2 replies; 9+ messages in thread From: devendra.aaru @ 2012-12-17 11:10 UTC (permalink / raw) To: Mikael Pettersson; +Cc: linux-wireless, linux-kernel On Mon, Dec 17, 2012 at 5:51 AM, Mikael Pettersson <mikpe@it.uu.se> wrote: > I just updated an old 1st gen AMD64 laptop from kernel 3.6.0 to 3.7.0, > Fedora 15 user-space, and was greeted by the following kernel warning: > > WARNING: at net/wireless/core.c:389 wiphy_register+0x5c3/0x600 [cfg80211]() I am seeing this line actually when i do vim +389 net/wireless/core.c. u16 all_iftypes = 0; its good if you tell us the top sha1 of yours? > Hardware name: SAM#451B > Modules linked in: rt2500pci(+) snd_mpu401_uart rt2x00pci snd_rawmidi rt2x00lib sg snd_seq_device mac80211 cfg80211 amd64_agp agpgart snd eeprom_93cx6 soundcore via_rhine mii evdev ipv6 ehci_hcd uhci_hcd sr_mod cdrom usbcore usb_common > Pid: 378, comm: modprobe Not tainted 3.7.0 #1 > Call Trace: > [<ffffffff810260b9>] ? warn_slowpath_common+0x79/0xc0 > [<ffffffffa0115773>] ? wiphy_register+0x5c3/0x600 [cfg80211] > [<ffffffff810c5b3f>] ? __kmalloc+0xef/0x170 > [<ffffffffa013ac97>] ? ieee80211_register_hw+0x347/0x6d0 [mac80211] > [<ffffffffa00f92ed>] ? rt2x00lib_probe_dev+0x53d/0x720 [rt2x00lib] > [<ffffffffa0060888>] ? rt2x00pci_probe+0x168/0x2e4 [rt2x00pci] > [<ffffffff81194cd0>] ? pci_device_probe+0xd0/0x170 > [<ffffffff811f2934>] ? driver_probe_device+0x64/0x210 > [<ffffffff811f2b73>] ? __driver_attach+0x93/0xa0 > [<ffffffff811f2ae0>] ? driver_probe_device+0x210/0x210 > [<ffffffff811f0f95>] ? bus_for_each_dev+0x45/0x80 > [<ffffffff811f20d8>] ? bus_add_driver+0x178/0x250 > [<ffffffff811f314e>] ? driver_register+0x6e/0x170 > [<ffffffff81048a14>] ? notifier_call_chain+0x44/0x60 > [<ffffffffa0196000>] ? 0xffffffffa0195fff > [<ffffffff810002ca>] ? do_one_initcall+0x11a/0x160 > [<ffffffff81069786>] ? sys_init_module+0x76/0x1c0 > [<ffffffff812c15d0>] ? system_call_fastpath+0x16/0x1b > ---[ end trace f8413f27de31929d ]--- > phy0 -> rt2x00lib_probe_dev: Error - Failed to initialize hw. > rt2500pci: probe of 0000:00:0c.0 failed with error -22 > > Rebooting into 3.6.0 shows no such error, booting 3.7.0 again shows the error, > so it's completely reproducible. > there are lots of WARN_ON's btw, :) may be one of them triggered, but please tell us the top sha1 of yours, so that the wireless dev's can easily see whats' happening with the rt2x00 to trigger this :) > lspci -v for the device in question: > > 00:0c.0 Network controller: Ralink corp. RT2500 802.11g (rev 01) > Subsystem: Micro-Star International Co., Ltd. Unknown 802.11g mini-PCI Adapter > Flags: bus master, slow devsel, latency 64, IRQ 18 > Memory at d0000000 (32-bit, non-prefetchable) [size=8K] > Capabilities: [40] Power Management version 2 > Kernel driver in use: rt2500pci > Kernel modules: rt2500pci > > I've never actually used or configured this device (the laptop is always > on wired ethernet), but thought you should know about this possible driver > regression. > > /Mikael > -- > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [3.7.0 regression] rt2x00lib_probe_dev: Error - Failed to initialize hw 2012-12-17 11:10 ` devendra.aaru @ 2012-12-17 11:11 ` devendra.aaru 2012-12-17 12:22 ` Mikael Pettersson 1 sibling, 0 replies; 9+ messages in thread From: devendra.aaru @ 2012-12-17 11:11 UTC (permalink / raw) To: Mikael Pettersson; +Cc: linux-wireless, linux-kernel > I am seeing this line actually when i do vim +389 net/wireless/core.c. > > u16 all_iftypes = 0; > > its good if you tell us the top sha1 of yours? i am sorry, btw mine's at a4f1de176614f634c367e5994a7bcc428c940df0. ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [3.7.0 regression] rt2x00lib_probe_dev: Error - Failed to initialize hw 2012-12-17 11:10 ` devendra.aaru 2012-12-17 11:11 ` devendra.aaru @ 2012-12-17 12:22 ` Mikael Pettersson 2012-12-17 12:59 ` devendra.aaru 1 sibling, 1 reply; 9+ messages in thread From: Mikael Pettersson @ 2012-12-17 12:22 UTC (permalink / raw) To: devendra.aaru; +Cc: Mikael Pettersson, linux-wireless, linux-kernel devendra.aaru writes: > On Mon, Dec 17, 2012 at 5:51 AM, Mikael Pettersson <mikpe@it.uu.se> wrote: > > I just updated an old 1st gen AMD64 laptop from kernel 3.6.0 to 3.7.0, > > Fedora 15 user-space, and was greeted by the following kernel warning: > > > > WARNING: at net/wireless/core.c:389 wiphy_register+0x5c3/0x600 [cfg80211]() > > I am seeing this line actually when i do vim +389 net/wireless/core.c. > > u16 all_iftypes = 0; > > its good if you tell us the top sha1 of yours? It's the plain linux-3.7.tar.xz from kernel.org, no git involved. Lines 389-390 of net/wireless/core.c are: if (WARN_ON(c->max_interfaces < 2)) return -EINVAL; /Mikael > > > > Hardware name: SAM#451B > > Modules linked in: rt2500pci(+) snd_mpu401_uart rt2x00pci snd_rawmidi rt2x00lib sg snd_seq_device mac80211 cfg80211 amd64_agp agpgart snd eeprom_93cx6 soundcore via_rhine mii evdev ipv6 ehci_hcd uhci_hcd sr_mod cdrom usbcore usb_common > > Pid: 378, comm: modprobe Not tainted 3.7.0 #1 > > Call Trace: > > [<ffffffff810260b9>] ? warn_slowpath_common+0x79/0xc0 > > [<ffffffffa0115773>] ? wiphy_register+0x5c3/0x600 [cfg80211] > > [<ffffffff810c5b3f>] ? __kmalloc+0xef/0x170 > > [<ffffffffa013ac97>] ? ieee80211_register_hw+0x347/0x6d0 [mac80211] > > [<ffffffffa00f92ed>] ? rt2x00lib_probe_dev+0x53d/0x720 [rt2x00lib] > > [<ffffffffa0060888>] ? rt2x00pci_probe+0x168/0x2e4 [rt2x00pci] > > [<ffffffff81194cd0>] ? pci_device_probe+0xd0/0x170 > > [<ffffffff811f2934>] ? driver_probe_device+0x64/0x210 > > [<ffffffff811f2b73>] ? __driver_attach+0x93/0xa0 > > [<ffffffff811f2ae0>] ? driver_probe_device+0x210/0x210 > > [<ffffffff811f0f95>] ? bus_for_each_dev+0x45/0x80 > > [<ffffffff811f20d8>] ? bus_add_driver+0x178/0x250 > > [<ffffffff811f314e>] ? driver_register+0x6e/0x170 > > [<ffffffff81048a14>] ? notifier_call_chain+0x44/0x60 > > [<ffffffffa0196000>] ? 0xffffffffa0195fff > > [<ffffffff810002ca>] ? do_one_initcall+0x11a/0x160 > > [<ffffffff81069786>] ? sys_init_module+0x76/0x1c0 > > [<ffffffff812c15d0>] ? system_call_fastpath+0x16/0x1b > > ---[ end trace f8413f27de31929d ]--- > > phy0 -> rt2x00lib_probe_dev: Error - Failed to initialize hw. > > rt2500pci: probe of 0000:00:0c.0 failed with error -22 > > > > Rebooting into 3.6.0 shows no such error, booting 3.7.0 again shows the error, > > so it's completely reproducible. > > > > there are lots of WARN_ON's btw, :) may be one of them triggered, but > please tell us the top sha1 of yours, so that the wireless dev's can > easily see whats' happening with the rt2x00 to trigger this :) > > > > lspci -v for the device in question: > > > > 00:0c.0 Network controller: Ralink corp. RT2500 802.11g (rev 01) > > Subsystem: Micro-Star International Co., Ltd. Unknown 802.11g mini-PCI Adapter > > Flags: bus master, slow devsel, latency 64, IRQ 18 > > Memory at d0000000 (32-bit, non-prefetchable) [size=8K] > > Capabilities: [40] Power Management version 2 > > Kernel driver in use: rt2500pci > > Kernel modules: rt2500pci > > > > I've never actually used or configured this device (the laptop is always > > on wired ethernet), but thought you should know about this possible driver > > regression. > > > > /Mikael > > -- > > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > > the body of a message to majordomo@vger.kernel.org > > More majordomo info at http://vger.kernel.org/majordomo-info.html > > Please read the FAQ at http://www.tux.org/lkml/ > ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [3.7.0 regression] rt2x00lib_probe_dev: Error - Failed to initialize hw 2012-12-17 12:22 ` Mikael Pettersson @ 2012-12-17 12:59 ` devendra.aaru 2012-12-17 13:21 ` Gertjan van Wingerde 0 siblings, 1 reply; 9+ messages in thread From: devendra.aaru @ 2012-12-17 12:59 UTC (permalink / raw) To: Mikael Pettersson; +Cc: linux-wireless, linux-kernel On Mon, Dec 17, 2012 at 7:22 AM, Mikael Pettersson <mikpe@it.uu.se> wrote: > devendra.aaru writes: > > On Mon, Dec 17, 2012 at 5:51 AM, Mikael Pettersson <mikpe@it.uu.se> wrote: > > > I just updated an old 1st gen AMD64 laptop from kernel 3.6.0 to 3.7.0, > > > Fedora 15 user-space, and was greeted by the following kernel warning: > > > > > > WARNING: at net/wireless/core.c:389 wiphy_register+0x5c3/0x600 [cfg80211]() > > > > I am seeing this line actually when i do vim +389 net/wireless/core.c. > > > > u16 all_iftypes = 0; > > > > its good if you tell us the top sha1 of yours? > > It's the plain linux-3.7.tar.xz from kernel.org, no git involved. > Lines 389-390 of net/wireless/core.c are: > > if (WARN_ON(c->max_interfaces < 2)) > return -EINVAL; > so its v3.7 tag hash 29594404d7fe73cd80eaa4ee8c43dcc53970c60e. i see that code line :). thanks i traced a while and looked at the rt2500pci.c code and there we are assigning the max_ap_intf variable to 1. the same go with the rt2800pci.c here's the part of the ops structure static const struct rt2x00_ops rt2500pci_ops = { .name = KBUILD_MODNAME, .max_ap_intf = 1, .eeprom_size = EEPROM_SIZE, .rf_size = RF_SIZE, .tx_queues = NUM_TX_QUEUES, .extra_tx_headroom = 0, .rx = &rt2500pci_queue_rx, .tx = &rt2500pci_queue_tx, .bcn = &rt2500pci_queue_bcn, .atim = &rt2500pci_queue_atim, .lib = &rt2500pci_rt2x00_ops, .hw = &rt2500pci_mac80211_ops, #ifdef CONFIG_RT2X00_LIB_DEBUGFS .debugfs = &rt2500pci_rt2x00debug, #endif /* CONFIG_RT2X00_LIB_DEBUGFS */ }; i really dont know why is that max_ap_intf is 1. may be some wireless dev's know about this? > /Mikael > ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [3.7.0 regression] rt2x00lib_probe_dev: Error - Failed to initialize hw 2012-12-17 12:59 ` devendra.aaru @ 2012-12-17 13:21 ` Gertjan van Wingerde 2012-12-17 13:57 ` Mikael Pettersson 2012-12-17 14:14 ` devendra.aaru 0 siblings, 2 replies; 9+ messages in thread From: Gertjan van Wingerde @ 2012-12-17 13:21 UTC (permalink / raw) To: devendra.aaru; +Cc: Mikael Pettersson, linux-wireless, linux-kernel Mikael, Devendra, On Mon, Dec 17, 2012 at 1:59 PM, devendra.aaru <devendra.aaru@gmail.com> wrote: > On Mon, Dec 17, 2012 at 7:22 AM, Mikael Pettersson <mikpe@it.uu.se> wrote: >> devendra.aaru writes: >> > On Mon, Dec 17, 2012 at 5:51 AM, Mikael Pettersson <mikpe@it.uu.se> wrote: >> > > I just updated an old 1st gen AMD64 laptop from kernel 3.6.0 to 3.7.0, >> > > Fedora 15 user-space, and was greeted by the following kernel warning: >> > > >> > > WARNING: at net/wireless/core.c:389 wiphy_register+0x5c3/0x600 [cfg80211]() >> > >> > I am seeing this line actually when i do vim +389 net/wireless/core.c. >> > >> > u16 all_iftypes = 0; >> > >> > its good if you tell us the top sha1 of yours? >> >> It's the plain linux-3.7.tar.xz from kernel.org, no git involved. >> Lines 389-390 of net/wireless/core.c are: >> >> if (WARN_ON(c->max_interfaces < 2)) >> return -EINVAL; >> > > so its v3.7 tag hash 29594404d7fe73cd80eaa4ee8c43dcc53970c60e. > > i see that code line :). thanks > > i traced a while and looked at the rt2500pci.c code and there we are > assigning the max_ap_intf variable to 1. the same go with the > rt2800pci.c > > here's the part of the ops structure > > static const struct rt2x00_ops rt2500pci_ops = { > .name = KBUILD_MODNAME, > .max_ap_intf = 1, > .eeprom_size = EEPROM_SIZE, > .rf_size = RF_SIZE, > .tx_queues = NUM_TX_QUEUES, > .extra_tx_headroom = 0, > .rx = &rt2500pci_queue_rx, > .tx = &rt2500pci_queue_tx, > .bcn = &rt2500pci_queue_bcn, > .atim = &rt2500pci_queue_atim, > .lib = &rt2500pci_rt2x00_ops, > .hw = &rt2500pci_mac80211_ops, > #ifdef CONFIG_RT2X00_LIB_DEBUGFS > .debugfs = &rt2500pci_rt2x00debug, > #endif /* CONFIG_RT2X00_LIB_DEBUGFS */ > }; > > i really dont know why is that max_ap_intf is 1. may be some wireless > dev's know about this? > > >> /Mikael This is caused by the introduction of interface combinations. Helmut Schaa has already submitted a patch to fix this, but this has unfortunately not ended up in 3.7. I'm confident it will end up in one of the upcoming 3.7.x stable releases. See http://marc.info/?l=linux-wireless&m=135478723823922&w=2 for the patch submitted by Helmut. --- Gertjan ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [3.7.0 regression] rt2x00lib_probe_dev: Error - Failed to initialize hw 2012-12-17 13:21 ` Gertjan van Wingerde @ 2012-12-17 13:57 ` Mikael Pettersson 2012-12-17 14:14 ` devendra.aaru 1 sibling, 0 replies; 9+ messages in thread From: Mikael Pettersson @ 2012-12-17 13:57 UTC (permalink / raw) To: Gertjan van Wingerde Cc: devendra.aaru, Mikael Pettersson, linux-wireless, linux-kernel Gertjan van Wingerde writes: > Mikael, Devendra, > > On Mon, Dec 17, 2012 at 1:59 PM, devendra.aaru <devendra.aaru@gmail.com> wrote: > > On Mon, Dec 17, 2012 at 7:22 AM, Mikael Pettersson <mikpe@it.uu.se> wrote: > >> devendra.aaru writes: > >> > On Mon, Dec 17, 2012 at 5:51 AM, Mikael Pettersson <mikpe@it.uu.se> wrote: > >> > > I just updated an old 1st gen AMD64 laptop from kernel 3.6.0 to 3.7.0, > >> > > Fedora 15 user-space, and was greeted by the following kernel warning: > >> > > > >> > > WARNING: at net/wireless/core.c:389 wiphy_register+0x5c3/0x600 [cfg80211]() ... > This is caused by the introduction of interface combinations. Helmut > Schaa has already submitted a patch to fix this, but this has > unfortunately not ended up in 3.7. I'm confident it will end up in one > of the upcoming 3.7.x stable releases. > > See http://marc.info/?l=linux-wireless&m=135478723823922&w=2 for the > patch submitted by Helmut. That patch fixes the problem. Thanks. /Mikael ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [3.7.0 regression] rt2x00lib_probe_dev: Error - Failed to initialize hw 2012-12-17 13:21 ` Gertjan van Wingerde 2012-12-17 13:57 ` Mikael Pettersson @ 2012-12-17 14:14 ` devendra.aaru 1 sibling, 0 replies; 9+ messages in thread From: devendra.aaru @ 2012-12-17 14:14 UTC (permalink / raw) To: Gertjan van Wingerde; +Cc: Mikael Pettersson, linux-wireless, linux-kernel > This is caused by the introduction of interface combinations. Helmut > Schaa has already submitted a patch to fix this, but this has > unfortunately not ended up in 3.7. I'm confident it will end up in one > of the upcoming 3.7.x stable releases. > > See http://marc.info/?l=linux-wireless&m=135478723823922&w=2 for the > patch submitted by Helmut. > --- > Gertjan thanks for the info, it seems that it fixes Mikael's problem. ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [3.7.0 regression] rt2x00lib_probe_dev: Error - Failed to initialize hw 2012-12-17 10:51 [3.7.0 regression] rt2x00lib_probe_dev: Error - Failed to initialize hw Mikael Pettersson 2012-12-17 11:10 ` devendra.aaru @ 2012-12-17 13:48 ` Stanislaw Gruszka 1 sibling, 0 replies; 9+ messages in thread From: Stanislaw Gruszka @ 2012-12-17 13:48 UTC (permalink / raw) To: Mikael Pettersson; +Cc: linux-wireless, linux-kernel On Mon, Dec 17, 2012 at 11:51:14AM +0100, Mikael Pettersson wrote: > I just updated an old 1st gen AMD64 laptop from kernel 3.6.0 to 3.7.0, > Fedora 15 user-space, and was greeted by the following kernel warning: > > WARNING: at net/wireless/core.c:389 wiphy_register+0x5c3/0x600 [cfg80211]() Already fixed on linus tree, should appear in 3.7 -stable soon. commit f5685ba675449b072feab6a5391a9ef9f604bc94 Author: Helmut Schaa <helmut.schaa@googlemail.com> Date: Mon Dec 3 22:35:39 2012 +0100 rt2x00: Only specify interface combinations if more then one interface is possible Stanislaw ^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2012-12-17 14:14 UTC | newest] Thread overview: 9+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2012-12-17 10:51 [3.7.0 regression] rt2x00lib_probe_dev: Error - Failed to initialize hw Mikael Pettersson 2012-12-17 11:10 ` devendra.aaru 2012-12-17 11:11 ` devendra.aaru 2012-12-17 12:22 ` Mikael Pettersson 2012-12-17 12:59 ` devendra.aaru 2012-12-17 13:21 ` Gertjan van Wingerde 2012-12-17 13:57 ` Mikael Pettersson 2012-12-17 14:14 ` devendra.aaru 2012-12-17 13:48 ` Stanislaw Gruszka
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).