From: Tino Keitel <tino.keitel@tikei.de>
To: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Pedro Francisco <pedrogfrancisco@gmail.com>,
ML linux-wireless <linux-wireless@vger.kernel.org>
Subject: Re: Power saving features for iwl4965
Date: Tue, 11 Jun 2013 20:55:03 +0200 [thread overview]
Message-ID: <20130611185503.GB8751@x61.home> (raw)
In-Reply-To: <20130611161924.GB1696@redhat.com>
Hi,
in my kernel log, I also see a SYSASSERT, but only once after resume
from suspend to RAM.
2013-06-11_18:40:58.80553 kern.notice: sd 0:0:0:0: [sda] Starting disk
2013-06-11_18:40:58.80554 kern.err: iwl4965 0000:03:00.0: Microcode SW
error detected. Restarting 0x82000000.
2013-06-11_18:40:58.80555 kern.err: iwl4965 0000:03:00.0: Loaded
firmware version: 228.61.2.24
2013-06-11_18:40:58.80556 kern.err: iwl4965 0000:03:00.0: Start IWL
Error Log Dump:
2013-06-11_18:40:58.80557 kern.err: iwl4965 0000:03:00.0: Status:
0x000313E4, count: 5
2013-06-11_18:40:58.80558 kern.err: iwl4965 0000:03:00.0: Desc
Time data1 data2 line
2013-06-11_18:40:58.80559 kern.err: iwl4965 0000:03:00.0: SYSASSERT
(0x0005) 0000000095 0x00000000 0x00000000 262
2013-06-11_18:40:58.80560 kern.err: iwl4965 0000:03:00.0: pc
blink1 blink2 ilink1 ilink2 hcmd
2013-06-11_18:40:58.80561 kern.err: iwl4965 0000:03:00.0: 0x0C924
0x0C90E 0x0C93A 0x006DA 0x00000 0x4090010
2013-06-11_18:40:58.80562 kern.err: iwl4965 0000:03:00.0: FH register
values:
2013-06-11_18:40:58.80563 kern.err: iwl4965 0000:03:00.0:
FH49_RSCSR_CHNL0_STTS_WPTR_REG: 0X0b101300
2013-06-11_18:40:58.80564 kern.err: iwl4965 0000:03:00.0:
FH49_RSCSR_CHNL0_RBDCB_BASE_REG: 0X00b10120
2013-06-11_18:40:58.80565 kern.err: iwl4965 0000:03:00.0:
FH49_RSCSR_CHNL0_WPTR: 0X00000008
2013-06-11_18:40:58.80565 kern.err: iwl4965 0000:03:00.0:
FH49_MEM_RCSR_CHNL0_CONFIG_REG: 0X80819000
2013-06-11_18:40:58.80566 kern.err: iwl4965 0000:03:00.0:
FH49_MEM_RSSR_SHARED_CTRL_REG: 0X0000003c
2013-06-11_18:40:58.80567 kern.err: iwl4965 0000:03:00.0:
FH49_MEM_RSSR_RX_STATUS_REG: 0X07030000
2013-06-11_18:40:58.80569 kern.err: iwl4965 0000:03:00.0:
FH49_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV: 0X00000000
2013-06-11_18:40:58.80570 kern.err: iwl4965 0000:03:00.0:
FH49_TSSR_TX_STATUS_REG: 0X07ff0002
2013-06-11_18:40:58.80571 kern.err: iwl4965 0000:03:00.0:
FH49_TSSR_TX_ERROR_REG: 0X00000000
2013-06-11_18:40:58.80572 kern.err: iwl4965 0000:03:00.0: Command
C_RXON failed: FW Error
2013-06-11_18:40:58.80575 kern.err: iwl4965 0000:03:00.0: Error setting
new RXON (-5)
2013-06-11_18:40:58.80576 kern.warn: iwl4965 0000:03:00.0: Try to add
interface when device not ready
Regards,
Tino
next prev parent reply other threads:[~2013-06-11 18:55 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-04-18 20:35 Power saving features for iwl4965 Tino Keitel
2012-04-19 14:25 ` Johannes Berg
2012-04-19 18:50 ` tino
2012-04-25 12:25 ` Stanislaw Gruszka
2012-05-03 18:28 ` Tino Keitel
2012-12-26 18:54 ` Tino Keitel
2013-01-07 11:08 ` Stanislaw Gruszka
2013-01-08 1:48 ` Pedro Francisco
2013-01-08 8:47 ` Stanislaw Gruszka
2013-06-03 8:52 ` Tino Keitel
2013-06-03 14:18 ` Stanislaw Gruszka
2013-06-09 0:28 ` Pedro Francisco
2013-06-10 19:31 ` Pedro Francisco
2013-06-11 16:19 ` Stanislaw Gruszka
2013-06-11 18:55 ` Tino Keitel [this message]
2013-06-14 12:50 ` Pedro Francisco
2013-06-14 13:18 ` Stanislaw Gruszka
2013-06-25 14:25 ` Stanislaw Gruszka
2013-07-11 21:02 ` Pedro Francisco
2013-07-16 10:27 ` Stanislaw Gruszka
2013-07-16 11:02 ` Pedro Francisco
2013-07-17 11:48 ` Pedro Francisco
2013-07-31 12:08 ` Stanislaw Gruszka
2013-08-04 14:24 ` Pedro Francisco
2013-08-04 14:53 ` Pedro Francisco
2013-10-17 9:06 ` Stanislaw Gruszka
2013-10-17 13:32 ` Stanislaw Gruszka
2013-06-11 18:51 ` Tino Keitel
2014-02-18 10:57 ` Stanislaw Gruszka
2014-02-18 11:32 ` Emmanuel Grumbach
2014-02-18 11:59 ` Stanislaw Gruszka
2014-02-20 12:08 ` Pedro Francisco
2014-02-25 16:16 ` Pedro Francisco
-- strict thread matches above, loose matches on Subject: below --
2012-10-01 16:06 Tino Keitel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20130611185503.GB8751@x61.home \
--to=tino.keitel@tikei.de \
--cc=linux-wireless@vger.kernel.org \
--cc=pedrogfrancisco@gmail.com \
--cc=sgruszka@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).