* iwlegacy: iwl4965 reload firmware issue.
@ 2013-10-01 8:17 Matt Chen
2013-10-02 9:19 ` Stanislaw Gruszka
0 siblings, 1 reply; 2+ messages in thread
From: Matt Chen @ 2013-10-01 8:17 UTC (permalink / raw)
To: linux-wireless; +Cc: kvoz123
Hi guys,
Recently a user reported a issue happened in his Intel 4965 wifi
issue. The issue happened to him is as below :
1. Boot system
2. Wait for 10 min
3. Look at dmesg output
412.869861] iwl4965 0000:03:00.0: Microcode SW error detected. Restarting
0x82000000.
[ 412.869867] iwl4965 0000:03:00.0: Loaded firmware version: 228.61.2.24
[ 412.869882] iwl4965 0000:03:00.0: Start IWL Error Log Dump:
[ 412.869884] iwl4965 0000:03:00.0: Status: 0x000213E4, count: 5
[ 412.870053] iwl4965 0000:03:00.0: Desc Time
data1 data2 line
[ 412.870056] iwl4965 0000:03:00.0: FH49_ERROR (0x000C)
1661571581 0x00000008 0x03130000 208
[ 412.870058] iwl4965 0000:03:00.0: pc blink1 blink2 ilink1 ilink2
hcmd
[ 412.870060] iwl4965 0000:03:00.0: 0x0046C 0x07A10 0x004C2 0x006DA 0x07A5A
0x2B0001C
[ 412.870062] iwl4965 0000:03:00.0: FH register values:
[ 412.870076] iwl4965 0000:03:00.0: FH49_RSCSR_CHNL0_STTS_WPTR_REG:
0X132c1e00
[ 412.870090] iwl4965 0000:03:00.0: FH49_RSCSR_CHNL0_RBDCB_BASE_REG:
0X0133bfe0
[ 412.870103] iwl4965 0000:03:00.0: FH49_RSCSR_CHNL0_WPTR:
0X000000f8
[ 412.870117] iwl4965 0000:03:00.0: FH49_MEM_RCSR_CHNL0_CONFIG_REG:
0X00819000
[ 412.870131] iwl4965 0000:03:00.0: FH49_MEM_RSSR_SHARED_CTRL_REG:
0X0000003c
[ 412.870144] iwl4965 0000:03:00.0: FH49_MEM_RSSR_RX_STATUS_REG:
0X03130000
[ 412.870158] iwl4965 0000:03:00.0: FH49_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV:
0X00000000
[ 412.870171] iwl4965 0000:03:00.0: FH49_TSSR_TX_STATUS_REG:
0X07ff0002
[ 412.870185] iwl4965 0000:03:00.0: FH49_TSSR_TX_ERROR_REG:
0X00000000
[ 412.870282] ieee80211 phy0: Hardware restart was requested
I traced the path, found it happened in
drivers/net/wireless/iwlegacy/4965-mac.c: il4965_irq_tasklet(), which
is handling the interrupt from pci bus. Also found it happenes in :
/* Error detected by uCode */
if (inta & CSR_INT_BIT_SW_ERR) {
IL_ERR("Microcode SW error detected. " " Restarting 0x%X.\n", inta);
il->isr_stats.sw++;
il_irq_handle_error(il);
handled |= CSR_INT_BIT_SW_ERR;
}
The restart path is through il_irq_handle_error(il). My question is if
this is a firmware issue, driver issue or hardware issue ?
Thanks.
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: iwlegacy: iwl4965 reload firmware issue.
2013-10-01 8:17 iwlegacy: iwl4965 reload firmware issue Matt Chen
@ 2013-10-02 9:19 ` Stanislaw Gruszka
0 siblings, 0 replies; 2+ messages in thread
From: Stanislaw Gruszka @ 2013-10-02 9:19 UTC (permalink / raw)
To: Matt Chen; +Cc: linux-wireless, kvoz123
On Tue, Oct 01, 2013 at 04:17:44PM +0800, Matt Chen wrote:
> The restart path is through il_irq_handle_error(il). My question is if
> this is a firmware issue, driver issue or hardware issue ?
Most likely driver issue, microcode error usually mean that driver provide
wrong values to the firmware or differently abuse firmware work.
Stanislaw
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2013-10-02 9:22 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2013-10-01 8:17 iwlegacy: iwl4965 reload firmware issue Matt Chen
2013-10-02 9:19 ` Stanislaw Gruszka
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).