From: Greg KH <gregkh@linuxfoundation.org>
To: Sanjeev Sharma <sanjeev_sharma@mentor.com>
Cc: Larry.Finger@lwfinger.net, Jes.Sorensen@redhat.com,
devel@driverdev.osuosl.org, linux-wireless@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH] staging:rtl8723au: core: Fix Warning reported by checkpatch.
Date: Thu, 6 Nov 2014 07:43:01 -0800 [thread overview]
Message-ID: <20141106154301.GC19605@kroah.com> (raw)
In-Reply-To: <1415255796-8471-1-git-send-email-sanjeev_sharma@mentor.com>
On Thu, Nov 06, 2014 at 12:06:36PM +0530, Sanjeev Sharma wrote:
> This is a patch to the rtw_cmd.c file that fixes following
> Warning by introducing temporary structure.
>
> WARNING: line over 80 characters
>
> Signed-off-by: Sanjeev Sharma <Sanjeev_Sharma@mentor.com>
> ---
> drivers/staging/rtl8723au/core/rtw_cmd.c | 123 +++++++++++++++----------------
> 1 file changed, 60 insertions(+), 63 deletions(-)
Same as the other patch, give us a hint as to the warning in the
subject.
>
> diff --git a/drivers/staging/rtl8723au/core/rtw_cmd.c b/drivers/staging/rtl8723au/core/rtw_cmd.c
> index 4eaa502..6186575 100644
> --- a/drivers/staging/rtl8723au/core/rtw_cmd.c
> +++ b/drivers/staging/rtl8723au/core/rtw_cmd.c
> @@ -919,34 +919,34 @@ static void traffic_status_watchdog(struct rtw_adapter *padapter)
> u8 bHigherBusyTxTraffic = false;
> struct mlme_priv *pmlmepriv = &padapter->mlmepriv;
> int BusyThreshold = 100;
> + struct rt_link_detect *ldi = &pmlmepriv->LinkDetectInfo;
> +
> /* */
> /* Determine if our traffic is busy now */
> /* */
> if (check_fwstate(pmlmepriv, _FW_LINKED)) {
> if (rtl8723a_BT_coexist(padapter))
> BusyThreshold = 50;
> - else if (pmlmepriv->LinkDetectInfo.bBusyTraffic)
> + else if (ldi->bBusyTraffic)
> BusyThreshold = 75;
> /* if we raise bBusyTraffic in last watchdog, using
> lower threshold. */
> - if (pmlmepriv->LinkDetectInfo.NumRxOkInPeriod > BusyThreshold ||
> - pmlmepriv->LinkDetectInfo.NumTxOkInPeriod > BusyThreshold) {
> + if (ldi->NumRxOkInPeriod > BusyThreshold ||
> + ldi->NumTxOkInPeriod > BusyThreshold) {
> bBusyTraffic = true;
>
> - if (pmlmepriv->LinkDetectInfo.NumRxOkInPeriod >
> - pmlmepriv->LinkDetectInfo.NumTxOkInPeriod)
> + if (ldi->NumRxOkInPeriod > ldi->NumTxOkInPeriod)
> bRxBusyTraffic = true;
> else
> bTxBusyTraffic = true;
> }
>
> /* Higher Tx/Rx data. */
> - if (pmlmepriv->LinkDetectInfo.NumRxOkInPeriod > 4000 ||
> - pmlmepriv->LinkDetectInfo.NumTxOkInPeriod > 4000) {
> + if (ldi->NumRxOkInPeriod > 4000 ||
> + ldi->NumTxOkInPeriod > 4000) {
> bHigherBusyTraffic = true;
>
> - if (pmlmepriv->LinkDetectInfo.NumRxOkInPeriod >
> - pmlmepriv->LinkDetectInfo.NumTxOkInPeriod)
> + if (ldi->NumRxOkInPeriod > ldi->NumTxOkInPeriod)
> bHigherBusyRxTraffic = true;
> else
> bHigherBusyTxTraffic = true;
> @@ -955,9 +955,9 @@ static void traffic_status_watchdog(struct rtw_adapter *padapter)
> if (!rtl8723a_BT_coexist(padapter) ||
> !rtl8723a_BT_using_antenna_1(padapter)) {
> /* check traffic for powersaving. */
> - if (((pmlmepriv->LinkDetectInfo.NumRxUnicastOkInPeriod +
> - pmlmepriv->LinkDetectInfo.NumTxOkInPeriod) > 8) ||
> - pmlmepriv->LinkDetectInfo.NumRxUnicastOkInPeriod >2)
> + if (((ldi->NumRxUnicastOkInPeriod +
> + ldi->NumTxOkInPeriod) > 8) ||
> + ldi->NumRxUnicastOkInPeriod > 2)
> bEnterPS = false;
> else
> bEnterPS = true;
> @@ -971,15 +971,15 @@ static void traffic_status_watchdog(struct rtw_adapter *padapter)
> } else
> LPS_Leave23a(padapter);
>
> - pmlmepriv->LinkDetectInfo.NumRxOkInPeriod = 0;
> - pmlmepriv->LinkDetectInfo.NumTxOkInPeriod = 0;
> - pmlmepriv->LinkDetectInfo.NumRxUnicastOkInPeriod = 0;
> - pmlmepriv->LinkDetectInfo.bBusyTraffic = bBusyTraffic;
> - pmlmepriv->LinkDetectInfo.bTxBusyTraffic = bTxBusyTraffic;
> - pmlmepriv->LinkDetectInfo.bRxBusyTraffic = bRxBusyTraffic;
> - pmlmepriv->LinkDetectInfo.bHigherBusyTraffic = bHigherBusyTraffic;
> - pmlmepriv->LinkDetectInfo.bHigherBusyRxTraffic = bHigherBusyRxTraffic;
> - pmlmepriv->LinkDetectInfo.bHigherBusyTxTraffic = bHigherBusyTxTraffic;
> + ldi->NumRxOkInPeriod = 0;
> + ldi->NumTxOkInPeriod = 0;
> + ldi->NumRxUnicastOkInPeriod = 0;
> + ldi->bBusyTraffic = bBusyTraffic;
> + ldi->bTxBusyTraffic = bTxBusyTraffic;
> + ldi->bRxBusyTraffic = bRxBusyTraffic;
> + ldi->bHigherBusyTraffic = bHigherBusyTraffic;
> + ldi->bHigherBusyRxTraffic = bHigherBusyRxTraffic;
> + ldi->bHigherBusyTxTraffic = bHigherBusyTxTraffic;
> }
>
> static void dynamic_chk_wk_hdl(struct rtw_adapter *padapter, u8 *pbuf, int sz)
> @@ -1017,46 +1017,44 @@ static void lps_ctrl_wk_hdl(struct rtw_adapter *padapter, u8 lps_ctrl_type)
> check_fwstate(pmlmepriv, WIFI_ADHOC_STATE))
> return;
>
> - switch (lps_ctrl_type)
> - {
> - case LPS_CTRL_SCAN:
> - rtl8723a_BT_wifiscan_notify(padapter, true);
> - if (!rtl8723a_BT_using_antenna_1(padapter)) {
> - if (check_fwstate(pmlmepriv, _FW_LINKED))
> - LPS_Leave23a(padapter);
> - }
> - break;
> - case LPS_CTRL_JOINBSS:
> - LPS_Leave23a(padapter);
> - break;
> - case LPS_CTRL_CONNECT:
> - mstatus = 1;/* connect */
> - /* Reset LPS Setting */
> - padapter->pwrctrlpriv.LpsIdleCount = 0;
> - rtl8723a_set_FwJoinBssReport_cmd(padapter, 1);
> - rtl8723a_BT_mediastatus_notify(padapter, mstatus);
> - break;
> - case LPS_CTRL_DISCONNECT:
> - mstatus = 0;/* disconnect */
> - rtl8723a_BT_mediastatus_notify(padapter, mstatus);
> - if (!rtl8723a_BT_using_antenna_1(padapter))
> - LPS_Leave23a(padapter);
> - rtl8723a_set_FwJoinBssReport_cmd(padapter, 0);
> - break;
> - case LPS_CTRL_SPECIAL_PACKET:
> - pwrpriv->DelayLPSLastTimeStamp = jiffies;
> - rtl8723a_BT_specialpacket_notify(padapter);
> - if (!rtl8723a_BT_using_antenna_1(padapter))
> - LPS_Leave23a(padapter);
> - break;
> - case LPS_CTRL_LEAVE:
> - rtl8723a_BT_lps_leave(padapter);
> - if (!rtl8723a_BT_using_antenna_1(padapter))
> + switch (lps_ctrl_type) {
> + case LPS_CTRL_SCAN:
> + rtl8723a_BT_wifiscan_notify(padapter, true);
> + if (!rtl8723a_BT_using_antenna_1(padapter)) {
> + if (check_fwstate(pmlmepriv, _FW_LINKED))
> LPS_Leave23a(padapter);
You are doing more than one thing here, something you did not specify in
your changelog above, which isn't ok :(
Please fix up and resend.
thanks,
greg k-h
next prev parent reply other threads:[~2014-11-06 15:44 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-10-27 7:59 [PATCH] staging:rtl8723au: core: Fix error reported by checkpatch Sanjeev Sharma
2014-10-27 8:43 ` Jes Sorensen
2014-10-27 14:52 ` Joe Perches
2014-10-29 6:35 ` Sharma, Sanjeev
2014-10-30 14:50 ` Jes Sorensen
2014-11-05 11:35 ` [PATCH v2] " Sanjeev Sharma
2014-11-05 16:27 ` Greg KH
2014-11-06 6:37 ` Sharma, Sanjeev
2014-11-05 17:15 ` Joe Perches
2014-11-06 5:41 ` Sharma, Sanjeev
2014-11-05 11:38 ` [PATCH] " Sharma, Sanjeev
2014-11-06 6:16 ` Sanjeev Sharma
2014-11-06 15:41 ` Greg KH
2014-11-07 11:56 ` Sharma, Sanjeev
2014-11-06 6:36 ` [PATCH] staging:rtl8723au: core: Fix Warning " Sanjeev Sharma
2014-11-06 15:43 ` Greg KH [this message]
2014-11-07 12:00 ` Sharma, Sanjeev
2014-11-07 15:46 ` Jes Sorensen
2014-11-11 7:54 ` [PATCH] staging:rtl8723au: core: Added missing space " Sanjeev Sharma
2014-11-11 9:58 ` [PATCH] staging:rtl8723au: core: Fix checkpatch warning Sanjeev Sharma
2014-10-30 7:47 ` [PATCH] staging:rtl8723au: core: Fix error reported by checkpatch Jes Sorensen
2014-10-29 6:32 ` Sharma, Sanjeev
2014-10-30 14:49 ` Jes Sorensen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20141106154301.GC19605@kroah.com \
--to=gregkh@linuxfoundation.org \
--cc=Jes.Sorensen@redhat.com \
--cc=Larry.Finger@lwfinger.net \
--cc=devel@driverdev.osuosl.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-wireless@vger.kernel.org \
--cc=sanjeev_sharma@mentor.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).