From: marco <marco@tampabay.rr.com>
To: wim torfs <wtorfs@gmail.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>,
linux-wireless@vger.kernel.org
Subject: Re: carl1970: monitor mode only displaying beacons/probs from APs?
Date: Fri, 6 Mar 2015 11:12:57 -0500 [thread overview]
Message-ID: <20150306161257.GA720@192.168.1.10> (raw)
In-Reply-To: <54F974B2.5050604@gmail.com>
On Fri, Mar 06, 2015 at 10:34:42AM +0100, wim torfs wrote:
> Hi,
>
> Perhaps a silly question, and I'm sure you already covered this, but I need
> to ask, just to be sure. Did you enable promiscuous mode to capture the data
> packets?
>
> Could you elaborate on the employed method for capturing the data, it is
> difficult to make any suggestions without having knowledge about the used
> procedure.
>
> Best Regards,
> Wim.
>
>
Hello Wim,
Honestly, I've never seen promiscuous mode get me anything when doing
wireless sniffing; probably because I'm not associated with an AP.
That being said, I have tried that without any noticeable difference.
I use both wireshark and tcpdump for my testing. I'm just looking for
wireless packets that one normally sees when doing wireless sniffing
(there is a lot of sta's / AP's around me) acks, CTS/RTS, various
management frames, etc. The missing traffic is pretty obvious when
comparing to another working wifi stick (in my case 9khtc).
I guess if this is not an obvious problem, I can go bisect until I
find where the problem was introduced. This was working fine in the
past.
Example: carl9170
It seem like all the traffic I see is from AP's, no STA. The three
types are all I ever see (1 data frame, and two mgmt frames, no
ctrl).
... -82dB signal antenna 5 Beacon (...) [1.0* 2.0* 2.0* 5...
... -81dB signal antenna 5 Beacon (...) [11.0* 11.0* 6....
... -57dB signal antenna 5 Beacon (...) [1.0* 2.0* 5.5* 11.0* ...
... -76dB signal antenna 5 Beacon (...) [1.0* 2.0* 5...
... -82dB signal antenna 5 Beacon (...) [1.0* 2.0* 2.0* 5...
... -82dB signal antenna 5 Probe Request () [1.0* 2.0* 5.5* 11.0...
... -57dB signal antenna 5 Beacon (...) [1.0* 2.0* 5.5* 11.0* ...
... -76dB signal antenna 5 Beacon (...) [1.0* 2.0* 5...
... -82dB signal antenna 5 Beacon (...) [1.0* 2.0* 2.0* 5...
... -83dB signal antenna 5 Beacon (...) [11.0* 11.0* 6....
... -82dB signal antenna 5 Beacon (...) [1.0* 2.0* 2.0* 5....
... -57dB signal antenna 5 Beacon (...) [1.0* 2.0* 5.5* 11.0* ...
... -76dB signal antenna 5 Beacon (...) [1.0* 2.0* 5...
... -83dB signal antenna 5 Beacon (...) [11.0* 11.0* 6....
... -74dB signal antenna 5 Data IV: c0 Pad 20 KeyID 1
... -74dB signal antenna 5 Beacon (...) [1.0* 2.0* 5.5* 11.0* ...
... -77dB signal antenna 5 Beacon (...) [1.0* 2.0* 5...
... -83dB signal antenna 5 Beacon (...) [1.0* 2.0* 2.0* 5...
... -82dB signal antenna 5 Beacon (...) [1.0* 2.0* 2.0* 5....
Example: 9k-htc
I see plenty of other frames (lots more in a larger sample)
... -75dB signal antenna 0 Unknown Ctrl Subtype
... -74dB signal antenna 0 Beacon (...) [1.0* 2.0* 5
... -74dB signal antenna 0 Beacon (...) [11.0* 11.
... -74dB signal antenna 0 Beacon (...) [1.0* 2.0*
... -76dB signal antenna 0 Beacon (...) [1.0* 2.0* 5.5*
... -76dB signal antenna 0 Beacon (...) [1.0* 2.0* 2
... -77dB signal antenna 0 Beacon (...) [1.0*
... -72dB signal antenna 0 Beacon (...) [1.0* 2.
... -73dB signal antenna 0 [|802.11]
... -73dB signal antenna 0 Unknown Ctrl Subtype
... -73dB signal antenna 0 Power Save-Poll AID
... -72dB signal antenna 0 Beacon (...) [1.0* 2.0* 5
... -72dB signal antenna 0 Beacon (...) [1.0* 2.
... -73dB signal antenna 0 Beacon (...) [1.0* 2.0*
... -75dB signal antenna 0 Beacon (...) ESS[|802.11]
... -76dB signal antenna 0 Beacon (...) [1.0* 2.0* 2
... -77dB signal antenna 0 CF Ack/Poll+QoS
... -78dB signal antenna 0 Data IV:363bbb Pad 20 KeyID 2
... -78dB signal antenna 0 Beacon (...) [1.0*
... -73dB signal antenna 0 Beacon (...) [1.0* 2.
... -74dB signal antenna 0 Beacon (...) [1.0* 2.0* 2.
... -75dB signal antenna 0 Unknown Ctrl Subtype
... -75dB signal antenna 0 Unknown Ctrl Subtype
Regards,
Marco
next prev parent reply other threads:[~2015-03-06 16:13 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-03-04 23:02 carl1970: monitor mode only displaying beacons/probs from APs? marco
2015-03-05 11:10 ` Christian Lamparter
2015-03-06 5:20 ` Marco
2015-03-06 9:34 ` wim torfs
2015-03-06 16:12 ` marco [this message]
2015-03-06 18:45 ` wim torfs
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20150306161257.GA720@192.168.1.10 \
--to=marco@tampabay.rr.com \
--cc=chunkeey@googlemail.com \
--cc=linux-wireless@vger.kernel.org \
--cc=wtorfs@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).