rt2800usb add usb ID 1b75:3070 for Airlive WT-2000USB

rt2800usb add usb ID 1b75:3070 for Airlive WT-2000USB

[Michael Coates]

Please add the following device USB ID to the rt2800usb source.

Brand: Airlive (Ovislink Corp.)
Name: Turbo-G USB Adaptor
Model: WT-2000USB
USB ID: 1b75:3070

After reading specs on this device, I figured the rt2800usb driver would work for this wireless adaptor.
I first tested by using the new_id function as follows:
echo "1b75 3070"> /sys/bus/usb/drivers/rt2800usb/new_id

I then added the following line to rt2800usb.c line with the other Ovislink devices.
        { USB_DEVICE(0x1b75, 0x3070) },
I complied the modified rt2800usb driver, both methods were successful. I have been using the adapter for a week and seams to be working perfectly. I believe that all that needs to be done to support this device is to add it's USB ID. Below is my dmesg output from when I plugged the device in and also when i connected the device to a Wireless network.


[362529.196944] usb 1-1.4: new high-speed USB device number 10 using dwc_otg
[362529.364504] usb 1-1.4: New USB device found, idVendor=1b75, idProduct=3070
[362529.413100] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[362529.461461] usb 1-1.4: Product: 802.11 n WLAN
[362529.506599] usb 1-1.4: Manufacturer: Ralink
[362529.550372] usb 1-1.4: SerialNumber: 1.0
[362529.676928] usb 1-1.4: reset high-speed USB device number 10 using dwc_otg
[362529.837456] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 3070, rev 0201 detected
[362529.893771] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 0005 detected
[362529.926673] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[362531.322079] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[362531.364536] ieee80211 phy1: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[362531.457883] ieee80211 phy1: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29[362531.877956] IPv6:
[362532.039655] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
-
[363081.295356] wlan0: authenticate with XX:XX:XX:f4:31:57
[363081.438322] wlan0: send auth to XX:XX:XX:f4:31:57 (try 1/3)
[363081.478769] wlan0: authenticated
[363081.521074] wlan0: associate with XX:XX:XX:f4:31:57 (try 1/3)
[363081.564347] wlan0: RX AssocResp from XX:XX:XX:f4:31:57 (capab=0x411 status=0 aid=4)
[363081.611086] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[363081.649247] wlan0: associated



 		 	   		  

[PATCH] rt2800usb: add usb ID 1b75:3070 for Airlive WT-2000USB

[Stanislaw Gruszka]

Brand: Airlive (Ovislink Corp.)
Name: Turbo-G USB Adaptor
Model: WT-2000USB
USB ID: 1b75:3070

Reported-and-tested-by: Michael Coates <michlinux@hotmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
---
 drivers/net/wireless/rt2x00/rt2800usb.c |    1 +
 1 files changed, 1 insertions(+), 0 deletions(-)

diff --git a/drivers/net/wireless/rt2x00/rt2800usb.c b/drivers/net/wireless/rt2x00/rt2800usb.c
index 5932306..bf9afbf 100644
--- a/drivers/net/wireless/rt2x00/rt2800usb.c
+++ b/drivers/net/wireless/rt2x00/rt2800usb.c
@@ -1114,6 +1114,7 @@ static struct usb_device_id rt2800usb_device_table[] = {
 	{ USB_DEVICE(0x0db0, 0x871c) },
 	{ USB_DEVICE(0x0db0, 0x899a) },
 	/* Ovislink */
+	{ USB_DEVICE(0x1b75, 0x3070) },
 	{ USB_DEVICE(0x1b75, 0x3071) },
 	{ USB_DEVICE(0x1b75, 0x3072) },
 	{ USB_DEVICE(0x1b75, 0xa200) },
-- 
1.7.1

Re: rt2800usb: add usb ID 1b75:3070 for Airlive WT-2000USB

[Kalle Valo]

> Brand: Airlive (Ovislink Corp.)
> Name: Turbo-G USB Adaptor
> Model: WT-2000USB
> USB ID: 1b75:3070
> 
> Reported-and-tested-by: Michael Coates <michlinux@hotmail.com>
> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>

Thanks, applied to wireless-drivers.git.

Kalle Valo