Re: wl12xx regression on 4.5 (was: Re: linux-4.5-rc1 TI pandboard-es wifi wlcore locks and reset)

[Emil Goode <emil.fsw@goode.io>]

Hello,

On Tue, Feb 02, 2016 at 05:05:38PM +0100, Sebastian Reichel wrote:
> On Tue, Feb 02, 2016 at 04:41:13PM +1100, Ross Green wrote:
> > On Tue, Feb 2, 2016 at 3:34 PM, Sebastian Reichel <sre@kernel.org> wrote:
> > > On Mon, Feb 01, 2016 at 11:38:38PM +1100, Ross Green wrote:
> > >> On Mon, Jan 25, 2016 at 11:47 PM, Ross Green <rgkernel@gmail.com> wrote:
> > >> > Just tried the new kernel release on faithful pandaboard es with the
> > >> > new 4.5-rc1 release.
> > >> >
> > >> > There is a problem with the wifi modules once the modules are loaded.
> > >> > Looks like the wifi firmware gets loaded put no response after that
> > >> > causing recovery action.
> > >> >
> > >> > the kernel 4.4 works quite happily with this board.
> > >> >
> > >> > Here is a dmesg dump in the attachment.
> > >> >
> > >> > Anyone have any ideas here?
> >
> > [...]
> > 
> > If I get time, this evening, I'll see if I can give a bisect a try.
> 
> On N950 [wl1271 via SPI, using extra patches to init from DT] I get wifi
> working again on 4.5-rc1 with 3719c17e1816 ("wlcore/wl18xx: fw logger
> over sdio") reverted.

Reverting the changes in wlcore_set_partition() as below seem to help.

Best regards,

Emil Goode

8<--------

--- a/drivers/net/wireless/ti/wlcore/io.c
+++ b/drivers/net/wireless/ti/wlcore/io.c
@@ -175,14 +175,15 @@ int wlcore_set_partition(struct wl1271 *wl,
 	if (ret < 0)
 		goto out;
 
+	/*
+	 * We don't need the size of the last partition, as it is
+	 * automatically calculated based on the total memory size and
+	 * the sizes of the previous partitions.
+	 */
 	ret = wlcore_raw_write32(wl, HW_PART3_START_ADDR, p->mem3.start);
 	if (ret < 0)
 		goto out;
 
-	ret = wlcore_raw_write32(wl, HW_PART3_SIZE_ADDR, p->mem3.size);
-	if (ret < 0)
-		goto out;
-
 out:
 	return ret;
 }
diff --git a/drivers/net/wireless/ti/wlcore/io.h b/drivers/net/wireless/ti/wlcore/io.h
index 6c257b5..10cf374 100644
--- a/drivers/net/wireless/ti/wlcore/io.h
+++ b/drivers/net/wireless/ti/wlcore/io.h
@@ -36,8 +36,8 @@
 #define HW_PART1_START_ADDR             (HW_PARTITION_REGISTERS_ADDR + 12)
 #define HW_PART2_SIZE_ADDR              (HW_PARTITION_REGISTERS_ADDR + 16)
 #define HW_PART2_START_ADDR             (HW_PARTITION_REGISTERS_ADDR + 20)
-#define HW_PART3_SIZE_ADDR              (HW_PARTITION_REGISTERS_ADDR + 24)
-#define HW_PART3_START_ADDR             (HW_PARTITION_REGISTERS_ADDR + 28)
+#define HW_PART3_START_ADDR             (HW_PARTITION_REGISTERS_ADDR + 24)
+
 #define HW_ACCESS_REGISTER_SIZE         4
 
 #define HW_ACCESS_PRAM_MAX_RANGE	0x3c000