From: Stanislaw Gruszka <sgruszka@redhat.com>
To: Tom Psyborg <pozega.tomislav@gmail.com>
Cc: Daniel Golle <daniel@makrotopia.org>,
linux-wireless@vger.kernel.org, Mathias Kresin <dev@kresin.me>,
Felix Fietkau <nbd@nbd.name>
Subject: Re: [PATCH v3 4/4] rt2800: fix registers init for MT7620
Date: Thu, 11 Oct 2018 12:05:25 +0200 [thread overview]
Message-ID: <20181011100524.GA20794@redhat.com> (raw)
In-Reply-To: <CAKR_QVLjFyGtzikLTiQKhrVBSyUoPmDn2tMJqto8dyBDjoFJOQ@mail.gmail.com>
On Wed, Oct 10, 2018 at 10:03:12PM +0200, Tom Psyborg wrote:
> ok, that is strange. do you see any performance differences without
> TX_SW_CFG regs? iperf test is a good pointer.
>
> this was a problem on xiaomi mini with old DD trunk builds on 4.4
> kernel and LEDE builds from last year. i ain't got no chance to try
> this on 18.06. which device you tried this on? if ipa/ilna it might
> make no difference
No diffrence for me. I have nexx wt3020 8M.
However I notice this set couse performance regression for me.
When connecting to iwl 7265 . Without the set I have:
root@LEDE:~# iperf3 -c 192.168.10.243
Connecting to host 192.168.10.243, port 5201
[ 5] local 192.168.10.1 port 59304 connected to 192.168.10.243 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 5.37 MBytes 44.9 Mbits/sec 0 279 KBytes
[ 5] 1.00-2.00 sec 5.80 MBytes 48.8 Mbits/sec 0 494 KBytes
[ 5] 2.00-3.00 sec 6.03 MBytes 50.5 Mbits/sec 0 513 KBytes
[ 5] 3.00-4.01 sec 5.90 MBytes 49.2 Mbits/sec 0 513 KBytes
[ 5] 4.01-5.01 sec 5.90 MBytes 49.5 Mbits/sec 0 515 KBytes
[ 5] 5.01-6.00 sec 5.78 MBytes 48.9 Mbits/sec 0 515 KBytes
[ 5] 6.00-7.00 sec 5.66 MBytes 47.4 Mbits/sec 0 515 KBytes
[ 5] 7.00-8.00 sec 6.03 MBytes 50.6 Mbits/sec 0 515 KBytes
[ 5] 8.00-9.00 sec 6.09 MBytes 50.9 Mbits/sec 0 515 KBytes
[ 5] 9.00-10.00 sec 5.72 MBytes 48.2 Mbits/sec 0 515 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 58.3 MBytes 48.9 Mbits/sec 0 sender
[ 5] 0.00-10.00 sec 58.3 MBytes 48.9 Mbits/sec receiver
With the set I have:
root@LEDE:~# iperf3 -c 192.168.10.243
Connecting to host 192.168.10.243, port 5201
[ 5] local 192.168.10.1 port 45824 connected to 192.168.10.243 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 3.78 MBytes 31.7 Mbits/sec 0 197 KBytes
[ 5] 1.00-2.00 sec 3.71 MBytes 31.0 Mbits/sec 0 369 KBytes
[ 5] 2.00-3.00 sec 3.51 MBytes 29.5 Mbits/sec 0 484 KBytes
[ 5] 3.00-4.00 sec 3.36 MBytes 28.1 Mbits/sec 0 519 KBytes
[ 5] 4.00-5.00 sec 4.10 MBytes 34.4 Mbits/sec 0 519 KBytes
[ 5] 5.00-6.00 sec 3.73 MBytes 31.2 Mbits/sec 0 519 KBytes
[ 5] 6.00-7.00 sec 4.29 MBytes 36.0 Mbits/sec 0 519 KBytes
[ 5] 7.00-8.00 sec 4.16 MBytes 34.9 Mbits/sec 0 519 KBytes
[ 5] 8.00-9.00 sec 4.35 MBytes 36.5 Mbits/sec 0 519 KBytes
[ 5] 9.00-10.00 sec 4.41 MBytes 37.0 Mbits/sec 0 519 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 39.4 MBytes 33.0 Mbits/sec 0 sender
[ 5] 0.00-10.00 sec 39.4 MBytes 33.0 Mbits/sec receiver
Stanislaw
next prev parent reply other threads:[~2018-10-11 10:05 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-10-09 11:56 [PATCH v3 1/4] rt2x00: remove unneeded check Stanislaw Gruszka
2018-10-09 11:56 ` [PATCH v3 2/4] rt2x00: remove confusing AGC register Stanislaw Gruszka
2018-10-09 12:27 ` Daniel Golle
2018-10-09 12:47 ` Stanislaw Gruszka
2018-10-09 13:07 ` Daniel Golle
2018-10-09 13:23 ` Stanislaw Gruszka
2018-10-09 11:56 ` [PATCH v3 3/4] rt2x00: update TX_SW_CFG2 value Stanislaw Gruszka
2018-10-09 11:56 ` [PATCH v3 4/4] rt2800: fix registers init for MT7620 Stanislaw Gruszka
2018-10-09 23:27 ` Tom Psyborg
2018-10-10 7:14 ` Stanislaw Gruszka
2018-10-10 12:06 ` Daniel Golle
2018-10-10 12:45 ` Stanislaw Gruszka
2018-10-10 14:11 ` Tom Psyborg
2018-10-10 15:40 ` Stanislaw Gruszka
2018-10-10 20:03 ` Tom Psyborg
2018-10-11 10:05 ` Stanislaw Gruszka [this message]
2018-10-11 12:39 ` Tom Psyborg
2018-10-12 8:50 ` Stanislaw Gruszka
2018-10-11 10:06 ` [PATCH v3 1/4] rt2x00: remove unneeded check Stanislaw Gruszka
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181011100524.GA20794@redhat.com \
--to=sgruszka@redhat.com \
--cc=daniel@makrotopia.org \
--cc=dev@kresin.me \
--cc=linux-wireless@vger.kernel.org \
--cc=nbd@nbd.name \
--cc=pozega.tomislav@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).