[PATCH AUTOSEL 4.4 01/53] ath10k: Do not send probe response template for mesh

[PATCH AUTOSEL 4.4 01/53] ath10k: Do not send probe response template for mesh

[Sasha Levin]

From: Surabhi Vishnoi <svishnoi@codeaurora.org>

[ Upstream commit 97354f2c432788e3163134df6bb144f4b6289d87 ]

Currently mac80211 do not support probe response template for
mesh point. When WMI_SERVICE_BEACON_OFFLOAD is enabled, host
driver tries to configure probe response template for mesh, but
it fails because the interface type is not NL80211_IFTYPE_AP but
NL80211_IFTYPE_MESH_POINT.

To avoid this failure, skip sending probe response template to
firmware for mesh point.

Tested HW: WCN3990/QCA6174/QCA9984

Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath10k/mac.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 398068ad0b62..5a0138c1c045 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -1502,6 +1502,10 @@ static int ath10k_mac_setup_prb_tmpl(struct ath10k_vif *arvif)
 	if (arvif->vdev_type != WMI_VDEV_TYPE_AP)
 		return 0;
 
+	 /* For mesh, probe response and beacon share the same template */
+	if (ieee80211_vif_is_mesh(vif))
+		return 0;
+
 	prb = ieee80211_proberesp_get(hw, vif);
 	if (!prb) {
 		ath10k_warn(ar, "failed to get probe resp template from mac80211\n");
-- 
2.20.1

[PATCH AUTOSEL 4.4 02/53] ath9k: Check for errors when reading SREV register

[Sasha Levin]

From: Tim Schumacher <timschumi@gmx.de>

[ Upstream commit 2f90c7e5d09437a4d8d5546feaae9f1cf48cfbe1 ]

Right now, if an error is encountered during the SREV register
read (i.e. an EIO in ath9k_regread()), that error code gets
passed all the way to __ath9k_hw_init(), where it is visible
during the "Chip rev not supported" message.

    ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
    ath: phy2: Mac Chip Rev 0x0f.3 is not supported by this driver
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath9k_htc: Failed to initialize the device

Check for -EIO explicitly in ath9k_hw_read_revisions() and return
a boolean based on the success of the operation. Check for that in
__ath9k_hw_init() and abort with a more debugging-friendly message
if reading the revisions wasn't successful.

    ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
    ath: phy2: Failed to read SREV register
    ath: phy2: Could not read hardware revision
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath9k_htc: Failed to initialize the device

This helps when debugging by directly showing the first point of
failure and it could prevent possible errors if a 0x0f.3 revision
is ever supported.

Signed-off-by: Tim Schumacher <timschumi@gmx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath9k/hw.c | 32 +++++++++++++++++++++--------
 1 file changed, 23 insertions(+), 9 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c
index 4435c7bbb625..d50e2e8bd998 100644
--- a/drivers/net/wireless/ath/ath9k/hw.c
+++ b/drivers/net/wireless/ath/ath9k/hw.c
@@ -250,8 +250,9 @@ void ath9k_hw_get_channel_centers(struct ath_hw *ah,
 /* Chip Revisions */
 /******************/
 
-static void ath9k_hw_read_revisions(struct ath_hw *ah)
+static bool ath9k_hw_read_revisions(struct ath_hw *ah)
 {
+	u32 srev;
 	u32 val;
 
 	if (ah->get_mac_revision)
@@ -267,25 +268,33 @@ static void ath9k_hw_read_revisions(struct ath_hw *ah)
 			val = REG_READ(ah, AR_SREV);
 			ah->hw_version.macRev = MS(val, AR_SREV_REVISION2);
 		}
-		return;
+		return true;
 	case AR9300_DEVID_AR9340:
 		ah->hw_version.macVersion = AR_SREV_VERSION_9340;
-		return;
+		return true;
 	case AR9300_DEVID_QCA955X:
 		ah->hw_version.macVersion = AR_SREV_VERSION_9550;
-		return;
+		return true;
 	case AR9300_DEVID_AR953X:
 		ah->hw_version.macVersion = AR_SREV_VERSION_9531;
-		return;
+		return true;
 	case AR9300_DEVID_QCA956X:
 		ah->hw_version.macVersion = AR_SREV_VERSION_9561;
-		return;
+		return true;
 	}
 
-	val = REG_READ(ah, AR_SREV) & AR_SREV_ID;
+	srev = REG_READ(ah, AR_SREV);
+
+	if (srev == -EIO) {
+		ath_err(ath9k_hw_common(ah),
+			"Failed to read SREV register");
+		return false;
+	}
+
+	val = srev & AR_SREV_ID;
 
 	if (val == 0xFF) {
-		val = REG_READ(ah, AR_SREV);
+		val = srev;
 		ah->hw_version.macVersion =
 			(val & AR_SREV_VERSION2) >> AR_SREV_TYPE2_S;
 		ah->hw_version.macRev = MS(val, AR_SREV_REVISION2);
@@ -304,6 +313,8 @@ static void ath9k_hw_read_revisions(struct ath_hw *ah)
 		if (ah->hw_version.macVersion == AR_SREV_VERSION_5416_PCIE)
 			ah->is_pciexpress = true;
 	}
+
+	return true;
 }
 
 /************************************/
@@ -556,7 +567,10 @@ static int __ath9k_hw_init(struct ath_hw *ah)
 	struct ath_common *common = ath9k_hw_common(ah);
 	int r = 0;
 
-	ath9k_hw_read_revisions(ah);
+	if (!ath9k_hw_read_revisions(ah)) {
+		ath_err(common, "Could not read hardware revisions");
+		return -EOPNOTSUPP;
+	}
 
 	switch (ah->hw_version.macVersion) {
 	case AR_SREV_VERSION_5416_PCI:
-- 
2.20.1

[PATCH AUTOSEL 4.4 03/53] ath6kl: add some bounds checking

[Sasha Levin]

From: Dan Carpenter <dan.carpenter@oracle.com>

[ Upstream commit 5d6751eaff672ea77642e74e92e6c0ac7f9709ab ]

The "ev->traffic_class" and "reply->ac" variables come from the network
and they're used as an offset into the wmi->stream_exist_for_ac[] array.
Those variables are u8 so they can be 0-255 but the stream_exist_for_ac[]
array only has WMM_NUM_AC (4) elements.  We need to add a couple bounds
checks to prevent array overflows.

I also modified one existing check from "if (traffic_class > 3) {" to
"if (traffic_class >= WMM_NUM_AC) {" just to make them all consistent.

Fixes: bdcd81707973 (" Add ath6kl cleaned up driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath6kl/wmi.c | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/ath6kl/wmi.c b/drivers/net/wireless/ath/ath6kl/wmi.c
index a5e1de75a4a3..b2ec254f154e 100644
--- a/drivers/net/wireless/ath/ath6kl/wmi.c
+++ b/drivers/net/wireless/ath/ath6kl/wmi.c
@@ -1178,6 +1178,10 @@ static int ath6kl_wmi_pstream_timeout_event_rx(struct wmi *wmi, u8 *datap,
 		return -EINVAL;
 
 	ev = (struct wmi_pstream_timeout_event *) datap;
+	if (ev->traffic_class >= WMM_NUM_AC) {
+		ath6kl_err("invalid traffic class: %d\n", ev->traffic_class);
+		return -EINVAL;
+	}
 
 	/*
 	 * When the pstream (fat pipe == AC) timesout, it means there were
@@ -1519,6 +1523,10 @@ static int ath6kl_wmi_cac_event_rx(struct wmi *wmi, u8 *datap, int len,
 		return -EINVAL;
 
 	reply = (struct wmi_cac_event *) datap;
+	if (reply->ac >= WMM_NUM_AC) {
+		ath6kl_err("invalid AC: %d\n", reply->ac);
+		return -EINVAL;
+	}
 
 	if ((reply->cac_indication == CAC_INDICATION_ADMISSION_RESP) &&
 	    (reply->status_code != IEEE80211_TSPEC_STATUS_ADMISS_ACCEPTED)) {
@@ -2631,7 +2639,7 @@ int ath6kl_wmi_delete_pstream_cmd(struct wmi *wmi, u8 if_idx, u8 traffic_class,
 	u16 active_tsids = 0;
 	int ret;
 
-	if (traffic_class > 3) {
+	if (traffic_class >= WMM_NUM_AC) {
 		ath6kl_err("invalid traffic class: %d\n", traffic_class);
 		return -EINVAL;
 	}
-- 
2.20.1

[PATCH AUTOSEL 4.4 04/53] ath: DFS JP domain W56 fixed pulse type 3 RADAR detection

[Sasha Levin]

From: Anilkumar Kolli <akolli@codeaurora.org>

[ Upstream commit d8792393a783158cbb2c39939cb897dc5e5299b6 ]

Increase pulse width range from 1-2usec to 0-4usec.
During data traffic HW occasionally fails detecting radar pulses,
so that SW cannot get enough radar reports to achieve the success rate.

Tested ath10k hw and fw:
	* QCA9888(10.4-3.5.1-00052)
	* QCA4019(10.4-3.2.1.1-00017)
	* QCA9984(10.4-3.6-00104)
	* QCA988X(10.2.4-1.0-00041)

Tested ath9k hw: AR9300

Tested-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/dfs_pattern_detector.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/dfs_pattern_detector.c b/drivers/net/wireless/ath/dfs_pattern_detector.c
index 2303ef96299d..0835828ffed7 100644
--- a/drivers/net/wireless/ath/dfs_pattern_detector.c
+++ b/drivers/net/wireless/ath/dfs_pattern_detector.c
@@ -111,7 +111,7 @@ static const struct radar_detector_specs jp_radar_ref_types[] = {
 	JP_PATTERN(0, 0, 1, 1428, 1428, 1, 18, 29, false),
 	JP_PATTERN(1, 2, 3, 3846, 3846, 1, 18, 29, false),
 	JP_PATTERN(2, 0, 1, 1388, 1388, 1, 18, 50, false),
-	JP_PATTERN(3, 1, 2, 4000, 4000, 1, 18, 50, false),
+	JP_PATTERN(3, 0, 4, 4000, 4000, 1, 18, 50, false),
 	JP_PATTERN(4, 0, 5, 150, 230, 1, 23, 50, false),
 	JP_PATTERN(5, 6, 10, 200, 500, 1, 16, 50, false),
 	JP_PATTERN(6, 11, 20, 200, 500, 1, 12, 50, false),
-- 
2.20.1

[PATCH AUTOSEL 4.4 41/53] mt7601u: do not schedule rx_tasklet when the device has been disconnected

[Sasha Levin]

From: Lorenzo Bianconi <lorenzo@kernel.org>

[ Upstream commit 4079e8ccabc3b6d1b503f2376123cb515d14921f ]

Do not schedule rx_tasklet when the usb dongle is disconnected.
Moreover do not grub rx_lock in mt7601u_kill_rx since usb_poison_urb
can run concurrently with urb completion and we can unlink urbs from rx
ring in any order.
This patch fixes the common kernel warning reported when
the device is removed.

[   24.921354] usb 3-14: USB disconnect, device number 7
[   24.921593] ------------[ cut here ]------------
[   24.921594] RX urb mismatch
[   24.921675] WARNING: CPU: 4 PID: 163 at drivers/net/wireless/mediatek/mt7601u/dma.c:200 mt7601u_complete_rx+0xcb/0xd0 [mt7601u]
[   24.921769] CPU: 4 PID: 163 Comm: kworker/4:2 Tainted: G           OE     4.19.31-041931-generic #201903231635
[   24.921770] Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./Z97 Extreme4, BIOS P1.30 05/23/2014
[   24.921782] Workqueue: usb_hub_wq hub_event
[   24.921797] RIP: 0010:mt7601u_complete_rx+0xcb/0xd0 [mt7601u]
[   24.921800] RSP: 0018:ffff9bd9cfd03d08 EFLAGS: 00010086
[   24.921802] RAX: 0000000000000000 RBX: ffff9bd9bf043540 RCX: 0000000000000006
[   24.921803] RDX: 0000000000000007 RSI: 0000000000000096 RDI: ffff9bd9cfd16420
[   24.921804] RBP: ffff9bd9cfd03d28 R08: 0000000000000002 R09: 00000000000003a8
[   24.921805] R10: 0000002f485fca34 R11: 0000000000000000 R12: ffff9bd9bf043c1c
[   24.921806] R13: ffff9bd9c62fa3c0 R14: 0000000000000082 R15: 0000000000000000
[   24.921807] FS:  0000000000000000(0000) GS:ffff9bd9cfd00000(0000) knlGS:0000000000000000
[   24.921808] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   24.921808] CR2: 00007fb2648b0000 CR3: 0000000142c0a004 CR4: 00000000001606e0
[   24.921809] Call Trace:
[   24.921812]  <IRQ>
[   24.921819]  __usb_hcd_giveback_urb+0x8b/0x140
[   24.921821]  usb_hcd_giveback_urb+0xca/0xe0
[   24.921828]  xhci_giveback_urb_in_irq.isra.42+0x82/0xf0
[   24.921834]  handle_cmd_completion+0xe02/0x10d0
[   24.921837]  xhci_irq+0x274/0x4a0
[   24.921838]  xhci_msi_irq+0x11/0x20
[   24.921851]  __handle_irq_event_percpu+0x44/0x190
[   24.921856]  handle_irq_event_percpu+0x32/0x80
[   24.921861]  handle_irq_event+0x3b/0x5a
[   24.921867]  handle_edge_irq+0x80/0x190
[   24.921874]  handle_irq+0x20/0x30
[   24.921889]  do_IRQ+0x4e/0xe0
[   24.921891]  common_interrupt+0xf/0xf
[   24.921892]  </IRQ>
[   24.921900] RIP: 0010:usb_hcd_flush_endpoint+0x78/0x180
[   24.921354] usb 3-14: USB disconnect, device number 7

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt7601u/dma.c | 33 +++++++++++----------
 1 file changed, 18 insertions(+), 15 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt7601u/dma.c b/drivers/net/wireless/mediatek/mt7601u/dma.c
index 57a80cfa39b1..6ba30129a3d8 100644
--- a/drivers/net/wireless/mediatek/mt7601u/dma.c
+++ b/drivers/net/wireless/mediatek/mt7601u/dma.c
@@ -193,10 +193,23 @@ static void mt7601u_complete_rx(struct urb *urb)
 	struct mt7601u_rx_queue *q = &dev->rx_q;
 	unsigned long flags;
 
-	spin_lock_irqsave(&dev->rx_lock, flags);
+	/* do no schedule rx tasklet if urb has been unlinked
+	 * or the device has been removed
+	 */
+	switch (urb->status) {
+	case -ECONNRESET:
+	case -ESHUTDOWN:
+	case -ENOENT:
+		return;
+	default:
+		dev_err_ratelimited(dev->dev, "rx urb failed: %d\n",
+				    urb->status);
+		/* fall through */
+	case 0:
+		break;
+	}
 
-	if (mt7601u_urb_has_error(urb))
-		dev_err(dev->dev, "Error: RX urb failed:%d\n", urb->status);
+	spin_lock_irqsave(&dev->rx_lock, flags);
 	if (WARN_ONCE(q->e[q->end].urb != urb, "RX urb mismatch"))
 		goto out;
 
@@ -363,19 +376,9 @@ int mt7601u_dma_enqueue_tx(struct mt7601u_dev *dev, struct sk_buff *skb,
 static void mt7601u_kill_rx(struct mt7601u_dev *dev)
 {
 	int i;
-	unsigned long flags;
 
-	spin_lock_irqsave(&dev->rx_lock, flags);
-
-	for (i = 0; i < dev->rx_q.entries; i++) {
-		int next = dev->rx_q.end;
-
-		spin_unlock_irqrestore(&dev->rx_lock, flags);
-		usb_poison_urb(dev->rx_q.e[next].urb);
-		spin_lock_irqsave(&dev->rx_lock, flags);
-	}
-
-	spin_unlock_irqrestore(&dev->rx_lock, flags);
+	for (i = 0; i < dev->rx_q.entries; i++)
+		usb_poison_urb(dev->rx_q.e[i].urb);
 }
 
 static int mt7601u_submit_rx_buf(struct mt7601u_dev *dev,
-- 
2.20.1

[PATCH AUTOSEL 4.4 43/53] mt7601u: fix possible memory leak when the device is disconnected

[Sasha Levin]

From: Lorenzo Bianconi <lorenzo@kernel.org>

[ Upstream commit 23377c200b2eb48a60d0f228b2a2e75ed6ee6060 ]

When the device is disconnected while passing traffic it is possible
to receive out of order urbs causing a memory leak since the skb linked
to the current tx urb is not removed. Fix the issue deallocating the skb
cleaning up the tx ring. Moreover this patch fixes the following kernel
warning

[   57.480771] usb 1-1: USB disconnect, device number 2
[   57.483451] ------------[ cut here ]------------
[   57.483462] TX urb mismatch
[   57.483481] WARNING: CPU: 1 PID: 32 at drivers/net/wireless/mediatek/mt7601u/dma.c:245 mt7601u_complete_tx+0x165/00
[   57.483483] Modules linked in:
[   57.483496] CPU: 1 PID: 32 Comm: kworker/1:1 Not tainted 5.2.0-rc1+ #72
[   57.483498] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.12.0-2.fc30 04/01/2014
[   57.483502] Workqueue: usb_hub_wq hub_event
[   57.483507] RIP: 0010:mt7601u_complete_tx+0x165/0x1e0
[   57.483510] Code: 8b b5 10 04 00 00 8b 8d 14 04 00 00 eb 8b 80 3d b1 cb e1 00 00 75 9e 48 c7 c7 a4 ea 05 82 c6 05 f
[   57.483513] RSP: 0000:ffffc900000a0d28 EFLAGS: 00010092
[   57.483516] RAX: 000000000000000f RBX: ffff88802c0a62c0 RCX: ffffc900000a0c2c
[   57.483518] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffff810a8371
[   57.483520] RBP: ffff88803ced6858 R08: 0000000000000000 R09: 0000000000000001
[   57.483540] R10: 0000000000000002 R11: 0000000000000000 R12: 0000000000000046
[   57.483542] R13: ffff88802c0a6c88 R14: ffff88803baab540 R15: ffff88803a0cc078
[   57.483548] FS:  0000000000000000(0000) GS:ffff88803eb00000(0000) knlGS:0000000000000000
[   57.483550] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   57.483552] CR2: 000055e7f6780100 CR3: 0000000028c86000 CR4: 00000000000006a0
[   57.483554] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   57.483556] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   57.483559] Call Trace:
[   57.483561]  <IRQ>
[   57.483565]  __usb_hcd_giveback_urb+0x77/0xe0
[   57.483570]  xhci_giveback_urb_in_irq.isra.0+0x8b/0x140
[   57.483574]  handle_cmd_completion+0xf5b/0x12c0
[   57.483577]  xhci_irq+0x1f6/0x1810
[   57.483581]  ? lockdep_hardirqs_on+0x9e/0x180
[   57.483584]  ? _raw_spin_unlock_irq+0x24/0x30
[   57.483588]  __handle_irq_event_percpu+0x3a/0x260
[   57.483592]  handle_irq_event_percpu+0x1c/0x60
[   57.483595]  handle_irq_event+0x2f/0x4c
[   57.483599]  handle_edge_irq+0x7e/0x1a0
[   57.483603]  handle_irq+0x17/0x20
[   57.483607]  do_IRQ+0x54/0x110
[   57.483610]  common_interrupt+0xf/0xf
[   57.483612]  </IRQ>

Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt7601u/dma.c | 21 ++++++++++++++++-----
 drivers/net/wireless/mediatek/mt7601u/tx.c  |  4 ++--
 2 files changed, 18 insertions(+), 7 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt7601u/dma.c b/drivers/net/wireless/mediatek/mt7601u/dma.c
index 6ba30129a3d8..3d0b9324d5bf 100644
--- a/drivers/net/wireless/mediatek/mt7601u/dma.c
+++ b/drivers/net/wireless/mediatek/mt7601u/dma.c
@@ -241,14 +241,25 @@ static void mt7601u_complete_tx(struct urb *urb)
 	struct sk_buff *skb;
 	unsigned long flags;
 
-	spin_lock_irqsave(&dev->tx_lock, flags);
+	switch (urb->status) {
+	case -ECONNRESET:
+	case -ESHUTDOWN:
+	case -ENOENT:
+		return;
+	default:
+		dev_err_ratelimited(dev->dev, "tx urb failed: %d\n",
+				    urb->status);
+		/* fall through */
+	case 0:
+		break;
+	}
 
-	if (mt7601u_urb_has_error(urb))
-		dev_err(dev->dev, "Error: TX urb failed:%d\n", urb->status);
+	spin_lock_irqsave(&dev->tx_lock, flags);
 	if (WARN_ONCE(q->e[q->start].urb != urb, "TX urb mismatch"))
 		goto out;
 
 	skb = q->e[q->start].skb;
+	q->e[q->start].skb = NULL;
 	trace_mt_tx_dma_done(dev, skb);
 
 	__skb_queue_tail(&dev->tx_skb_done, skb);
@@ -448,10 +459,10 @@ static void mt7601u_free_tx_queue(struct mt7601u_tx_queue *q)
 {
 	int i;
 
-	WARN_ON(q->used);
-
 	for (i = 0; i < q->entries; i++)  {
 		usb_poison_urb(q->e[i].urb);
+		if (q->e[i].skb)
+			mt7601u_tx_status(q->dev, q->e[i].skb);
 		usb_free_urb(q->e[i].urb);
 	}
 }
diff --git a/drivers/net/wireless/mediatek/mt7601u/tx.c b/drivers/net/wireless/mediatek/mt7601u/tx.c
index a0a33dc8f6bc..a1b6db2a8937 100644
--- a/drivers/net/wireless/mediatek/mt7601u/tx.c
+++ b/drivers/net/wireless/mediatek/mt7601u/tx.c
@@ -117,9 +117,9 @@ void mt7601u_tx_status(struct mt7601u_dev *dev, struct sk_buff *skb)
 	info->status.rates[0].idx = -1;
 	info->flags |= IEEE80211_TX_STAT_ACK;
 
-	spin_lock(&dev->mac_lock);
+	spin_lock_bh(&dev->mac_lock);
 	ieee80211_tx_status(dev->hw, skb);
-	spin_unlock(&dev->mac_lock);
+	spin_unlock_bh(&dev->mac_lock);
 }
 
 static int mt7601u_skb_rooms(struct mt7601u_dev *dev, struct sk_buff *skb)
-- 
2.20.1

[PATCH AUTOSEL 4.4 44/53] ath10k: fix PCIE device wake up failed

[Sasha Levin]

From: Miaoqing Pan <miaoqing@codeaurora.org>

[ Upstream commit 011d4111c8c602ea829fa4917af1818eb0500a90 ]

Observed PCIE device wake up failed after ~120 iterations of
soft-reboot test. The error message is
"ath10k_pci 0000:01:00.0: failed to wake up device : -110"

The call trace as below:
ath10k_pci_probe -> ath10k_pci_force_wake -> ath10k_pci_wake_wait ->
ath10k_pci_is_awake

Once trigger the device to wake up, we will continuously check the RTC
state until it returns RTC_STATE_V_ON or timeout.

But for QCA99x0 chips, we use wrong value for RTC_STATE_V_ON.
Occasionally, we get 0x7 on the fist read, we thought as a failure
case, but actually is the right value, also verified with the spec.
So fix the issue by changing RTC_STATE_V_ON from 0x5 to 0x7, passed
~2000 iterations.

Tested HW: QCA9984

Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath10k/hw.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/ath10k/hw.c b/drivers/net/wireless/ath/ath10k/hw.c
index 7b84d08a5154..12d6549e45a1 100644
--- a/drivers/net/wireless/ath/ath10k/hw.c
+++ b/drivers/net/wireless/ath/ath10k/hw.c
@@ -128,7 +128,7 @@ const struct ath10k_hw_values qca6174_values = {
 };
 
 const struct ath10k_hw_values qca99x0_values = {
-	.rtc_state_val_on		= 5,
+	.rtc_state_val_on		= 7,
 	.ce_count			= 12,
 	.msi_assign_ce_max		= 12,
 	.num_target_ce_config_wlan	= 10,
-- 
2.20.1