From: Kalle Valo <kvalo@codeaurora.org>
To: <yhchuang@realtek.com>
Cc: <linux-wireless@vger.kernel.org>, <briannorris@chromium.org>
Subject: Re: [PATCH 02/15] rtw88: configure firmware after HCI started
Date: Sat, 21 Sep 2019 05:51:05 +0000 (UTC) [thread overview]
Message-ID: <20190921055105.296A761359@smtp.codeaurora.org> (raw)
In-Reply-To: <1568617425-28062-3-git-send-email-yhchuang@realtek.com>
<yhchuang@realtek.com> wrote:
> From: Yan-Hsuan Chuang <yhchuang@realtek.com>
>
> After firmware has been downloaded, driver should send
> some information to it through H2C commands. Those H2C
> commands are transmitted through TX path.
>
> But before HCI has been started, the TX path is not
> working completely. Such as PCI interfaces, the interrupts
> are not enabled, hence TX interrupts will not be issued
> after H2C skb has been DMAed to the device. And the H2C
> skbs will not be released until the device is powered off.
>
> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
This didn't apply. Please rebase on top of wireless-drivers, mark this
as "[PATCH 5.4 v2]" and resend.
fatal: sha1 information is lacking or useless (drivers/net/wireless/realtek/rtw88/mac.c).
error: could not build fake ancestor
Applying: rtw88: configure firmware after HCI started
Patch failed at 0001 rtw88: configure firmware after HCI started
The copy of the patch that failed is found in: .git/rebase-apply/patch
Patch set to Changes Requested.
--
https://patchwork.kernel.org/patch/11146411/
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
next prev parent reply other threads:[~2019-09-21 5:51 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-09-16 7:03 [PATCH 00/15] rtw88: Add support for deep PS mode yhchuang
2019-09-16 7:03 ` [PATCH 01/15] rtw88: remove redundant flag check helper function yhchuang
2019-10-01 9:17 ` Kalle Valo
2019-09-16 7:03 ` [PATCH 02/15] rtw88: configure firmware after HCI started yhchuang
2019-09-21 5:51 ` Kalle Valo [this message]
2019-09-16 7:03 ` [PATCH 03/15] rtw88: pci: reset H2C queue indexes in a single write yhchuang
2019-09-16 7:03 ` [PATCH 04/15] rtw88: pci: extract skbs free routine for trx rings yhchuang
2019-09-21 5:47 ` Kalle Valo
2019-09-16 7:03 ` [PATCH 05/15] rtw88: pci: release tx skbs DMAed when stop yhchuang
2019-09-18 0:41 ` Brian Norris
2019-09-18 2:10 ` Tony Chuang
2019-09-20 0:35 ` Brian Norris
2019-09-20 7:26 ` Kalle Valo
2019-09-20 8:29 ` Tony Chuang
2019-09-20 8:35 ` Kalle Valo
2019-09-20 22:33 ` Brian Norris
2019-09-16 7:03 ` [PATCH 06/15] rtw88: not to enter or leave PS under IRQ yhchuang
2019-09-16 7:03 ` [PATCH 07/15] rtw88: not to control LPS by each vif yhchuang
2019-09-16 7:03 ` [PATCH 08/15] rtw88: remove unused lps state check helper yhchuang
2019-09-16 7:03 ` [PATCH 09/15] rtw88: LPS enter/leave should be protected by lock yhchuang
2019-09-16 7:03 ` [PATCH 10/15] rtw88: leave PS state for dynamic mechanism yhchuang
2019-09-16 7:03 ` [PATCH 11/15] rtw88: add deep power save support yhchuang
2019-09-16 7:03 ` [PATCH 12/15] rtw88: not to enter LPS by coex strategy yhchuang
2019-09-16 7:03 ` [PATCH 13/15] rtw88: select deep PS mode when module is inserted yhchuang
2019-09-16 7:03 ` [PATCH 14/15] rtw88: add deep PS PG mode for 8822c yhchuang
2019-09-16 7:03 ` [PATCH 15/15] rtw88: remove misleading module parameter rtw_fw_support_lps yhchuang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190921055105.296A761359@smtp.codeaurora.org \
--to=kvalo@codeaurora.org \
--cc=briannorris@chromium.org \
--cc=linux-wireless@vger.kernel.org \
--cc=yhchuang@realtek.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).