[PATCH AUTOSEL 5.4 44/74] wlcore/wl12xx: Fix wl12xx get_mac error if device is in ELP

[PATCH AUTOSEL 5.4 44/74] wlcore/wl12xx: Fix wl12xx get_mac error if device is in ELP

[Sasha Levin]

From: Tony Lindgren <tony@atomide.com>

[ Upstream commit 11ef6bc846dcdce838f0b00c5f6a562c57e5d43b ]

At least on wl12xx, reading the MAC after boot can fail with a warning
at drivers/net/wireless/ti/wlcore/sdio.c:78 wl12xx_sdio_raw_read.
The failed call comes from wl12xx_get_mac() that wlcore_nvs_cb() calls
after request_firmware_work_func().

After the error, no wireless interface is created. Reloading the wl12xx
module makes the interface work.

Turns out the wlan controller can be in a low-power ELP state after the
boot from the bootloader or kexec, and needs to be woken up first.

Let's wake the hardware and add a sleep after that similar to
wl12xx_pre_boot() is already doing.

Note that a similar issue could exist for wl18xx, but I have not seen it
so far. And a search for wl18xx_get_mac and wl12xx_sdio_raw_read did not
produce similar errors.

Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210603062814.19464-1-tony@atomide.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ti/wl12xx/main.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/drivers/net/wireless/ti/wl12xx/main.c b/drivers/net/wireless/ti/wl12xx/main.c
index 9d7dbfe7fe0c..c6da0cfb4afb 100644
--- a/drivers/net/wireless/ti/wl12xx/main.c
+++ b/drivers/net/wireless/ti/wl12xx/main.c
@@ -1503,6 +1503,13 @@ static int wl12xx_get_fuse_mac(struct wl1271 *wl)
 	u32 mac1, mac2;
 	int ret;
 
+	/* Device may be in ELP from the bootloader or kexec */
+	ret = wlcore_write32(wl, WL12XX_WELP_ARM_COMMAND, WELP_ARM_COMMAND_VAL);
+	if (ret < 0)
+		goto out;
+
+	usleep_range(500000, 700000);
+
 	ret = wlcore_set_partition(wl, &wl->ptable[PART_DRPW]);
 	if (ret < 0)
 		goto out;
-- 
2.30.2

[PATCH AUTOSEL 5.4 45/74] wl1251: Fix possible buffer overflow in wl1251_cmd_scan

[Sasha Levin]

From: Lee Gibson <leegib@gmail.com>

[ Upstream commit d10a87a3535cce2b890897914f5d0d83df669c63 ]

Function wl1251_cmd_scan calls memcpy without checking the length.
Harden by checking the length is within the maximum allowed size.

Signed-off-by: Lee Gibson <leegib@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210428115508.25624-1-leegib@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ti/wl1251/cmd.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/drivers/net/wireless/ti/wl1251/cmd.c b/drivers/net/wireless/ti/wl1251/cmd.c
index 9547aea01b0f..ea0215246c5c 100644
--- a/drivers/net/wireless/ti/wl1251/cmd.c
+++ b/drivers/net/wireless/ti/wl1251/cmd.c
@@ -466,9 +466,12 @@ int wl1251_cmd_scan(struct wl1251 *wl, u8 *ssid, size_t ssid_len,
 		cmd->channels[i].channel = channels[i]->hw_value;
 	}
 
-	cmd->params.ssid_len = ssid_len;
-	if (ssid)
-		memcpy(cmd->params.ssid, ssid, ssid_len);
+	if (ssid) {
+		int len = clamp_val(ssid_len, 0, IEEE80211_MAX_SSID_LEN);
+
+		cmd->params.ssid_len = len;
+		memcpy(cmd->params.ssid, ssid, len);
+	}
 
 	ret = wl1251_cmd_send(wl, CMD_SCAN, cmd, sizeof(*cmd));
 	if (ret < 0) {
-- 
2.30.2

[PATCH AUTOSEL 5.4 46/74] cw1200: add missing MODULE_DEVICE_TABLE

[Sasha Levin]

From: Zou Wei <zou_wei@huawei.com>

[ Upstream commit dd778f89225cd258e8f0fed2b7256124982c8bb5 ]

This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1620788714-14300-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/st/cw1200/cw1200_sdio.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/wireless/st/cw1200/cw1200_sdio.c b/drivers/net/wireless/st/cw1200/cw1200_sdio.c
index 43e012073dbf..5ac06d672fc6 100644
--- a/drivers/net/wireless/st/cw1200/cw1200_sdio.c
+++ b/drivers/net/wireless/st/cw1200/cw1200_sdio.c
@@ -60,6 +60,7 @@ static const struct sdio_device_id cw1200_sdio_ids[] = {
 	{ SDIO_DEVICE(SDIO_VENDOR_ID_STE, SDIO_DEVICE_ID_STE_CW1200) },
 	{ /* end: all zeroes */			},
 };
+MODULE_DEVICE_TABLE(sdio, cw1200_sdio_ids);
 
 /* hwbus_ops implemetation */
 
-- 
2.30.2

[PATCH AUTOSEL 5.4 48/74] mt76: mt7615: fix fixed-rate tx status reporting

[Sasha Levin]

From: Felix Fietkau <nbd@nbd.name>

[ Upstream commit ec8f1a90d006f7cedcf86ef19fd034a406a213d6 ]

Rely on the txs fixed-rate bit instead of info->control.rates

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt76/mt7615/mac.c | 10 ++++------
 1 file changed, 4 insertions(+), 6 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt76/mt7615/mac.c b/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
index 111e38ff954a..a6c530b9ceee 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
@@ -840,22 +840,20 @@ static bool mt7615_fill_txs(struct mt7615_dev *dev, struct mt7615_sta *sta,
 	int first_idx = 0, last_idx;
 	int i, idx, count;
 	bool fixed_rate, ack_timeout;
-	bool probe, ampdu, cck = false;
+	bool ampdu, cck = false;
 	bool rs_idx;
 	u32 rate_set_tsf;
 	u32 final_rate, final_rate_flags, final_nss, txs;
 
-	fixed_rate = info->status.rates[0].count;
-	probe = !!(info->flags & IEEE80211_TX_CTL_RATE_CTRL_PROBE);
-
 	txs = le32_to_cpu(txs_data[1]);
-	ampdu = !fixed_rate && (txs & MT_TXS1_AMPDU);
+	ampdu = txs & MT_TXS1_AMPDU;
 
 	txs = le32_to_cpu(txs_data[3]);
 	count = FIELD_GET(MT_TXS3_TX_COUNT, txs);
 	last_idx = FIELD_GET(MT_TXS3_LAST_TX_RATE, txs);
 
 	txs = le32_to_cpu(txs_data[0]);
+	fixed_rate = txs & MT_TXS0_FIXED_RATE;
 	final_rate = FIELD_GET(MT_TXS0_TX_RATE, txs);
 	ack_timeout = txs & MT_TXS0_ACK_TIMEOUT;
 
@@ -877,7 +875,7 @@ static bool mt7615_fill_txs(struct mt7615_dev *dev, struct mt7615_sta *sta,
 
 	first_idx = max_t(int, 0, last_idx - (count + 1) / MT7615_RATE_RETRY);
 
-	if (fixed_rate && !probe) {
+	if (fixed_rate) {
 		info->status.rates[0].count = count;
 		i = 0;
 		goto out;
-- 
2.30.2

[PATCH AUTOSEL 5.4 52/74] rtl8xxxu: Fix device info for RTL8192EU devices

[Sasha Levin]

From: Pascal Terjan <pterjan@google.com>

[ Upstream commit c240b044edefa3c3af4014a4030e017dd95b59a1 ]

Based on 2001:3319 and 2357:0109 which I used to test the fix and
0bda:818b and 2357:0108 for which I found efuse dumps online.

== 2357:0109 ==
=== Before ===
Vendor: Realtek
Product: \x03802.11n NI
Serial:
=== After ===
Vendor: Realtek
Product: 802.11n NIC
Serial not available.

== 2001:3319 ==
=== Before ===
Vendor: Realtek
Product: Wireless N
Serial: no USB Adap
=== After ===
Vendor: Realtek
Product: Wireless N Nano USB Adapter
Serial not available.

Signed-off-by: Pascal Terjan <pterjan@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210424172959.1559890-1-pterjan@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../net/wireless/realtek/rtl8xxxu/rtl8xxxu.h  | 11 +---
 .../realtek/rtl8xxxu/rtl8xxxu_8192e.c         | 59 +++++++++++++++++--
 2 files changed, 56 insertions(+), 14 deletions(-)

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h
index 5e9ce03067de..6858f7de0915 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h
@@ -853,15 +853,10 @@ struct rtl8192eu_efuse {
 	u8 usb_optional_function;
 	u8 res9[2];
 	u8 mac_addr[ETH_ALEN];		/* 0xd7 */
-	u8 res10[2];
-	u8 vendor_name[7];
-	u8 res11[2];
-	u8 device_name[0x0b];		/* 0xe8 */
-	u8 res12[2];
-	u8 serial[0x0b];		/* 0xf5 */
-	u8 res13[0x30];
+	u8 device_info[80];
+	u8 res11[3];
 	u8 unknown[0x0d];		/* 0x130 */
-	u8 res14[0xc3];
+	u8 res12[0xc3];
 };
 
 struct rtl8xxxu_reg8val {
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8192e.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8192e.c
index c747f6a1922d..02ca80501c3a 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8192e.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8192e.c
@@ -554,9 +554,43 @@ rtl8192e_set_tx_power(struct rtl8xxxu_priv *priv, int channel, bool ht40)
 	}
 }
 
+static void rtl8192eu_log_next_device_info(struct rtl8xxxu_priv *priv,
+					   char *record_name,
+					   char *device_info,
+					   unsigned int *record_offset)
+{
+	char *record = device_info + *record_offset;
+
+	/* A record is [ total length | 0x03 | value ] */
+	unsigned char l = record[0];
+
+	/*
+	 * The whole device info section seems to be 80 characters, make sure
+	 * we don't read further.
+	 */
+	if (*record_offset + l > 80) {
+		dev_warn(&priv->udev->dev,
+			 "invalid record length %d while parsing \"%s\" at offset %u.\n",
+			 l, record_name, *record_offset);
+		return;
+	}
+
+	if (l >= 2) {
+		char value[80];
+
+		memcpy(value, &record[2], l - 2);
+		value[l - 2] = '\0';
+		dev_info(&priv->udev->dev, "%s: %s\n", record_name, value);
+		*record_offset = *record_offset + l;
+	} else {
+		dev_info(&priv->udev->dev, "%s not available.\n", record_name);
+	}
+}
+
 static int rtl8192eu_parse_efuse(struct rtl8xxxu_priv *priv)
 {
 	struct rtl8192eu_efuse *efuse = &priv->efuse_wifi.efuse8192eu;
+	unsigned int record_offset;
 	int i;
 
 	if (efuse->rtl_id != cpu_to_le16(0x8129))
@@ -604,12 +638,25 @@ static int rtl8192eu_parse_efuse(struct rtl8xxxu_priv *priv)
 	priv->has_xtalk = 1;
 	priv->xtalk = priv->efuse_wifi.efuse8192eu.xtal_k & 0x3f;
 
-	dev_info(&priv->udev->dev, "Vendor: %.7s\n", efuse->vendor_name);
-	dev_info(&priv->udev->dev, "Product: %.11s\n", efuse->device_name);
-	if (memchr_inv(efuse->serial, 0xff, 11))
-		dev_info(&priv->udev->dev, "Serial: %.11s\n", efuse->serial);
-	else
-		dev_info(&priv->udev->dev, "Serial not available.\n");
+	/*
+	 * device_info section seems to be laid out as records
+	 * [ total length | 0x03 | value ] so:
+	 * - vendor length + 2
+	 * - 0x03
+	 * - vendor string (not null terminated)
+	 * - product length + 2
+	 * - 0x03
+	 * - product string (not null terminated)
+	 * Then there is one or 2 0x00 on all the 4 devices I own or found
+	 * dumped online.
+	 * As previous version of the code handled an optional serial
+	 * string, I now assume there may be a third record if the
+	 * length is not 0.
+	 */
+	record_offset = 0;
+	rtl8192eu_log_next_device_info(priv, "Vendor", efuse->device_info, &record_offset);
+	rtl8192eu_log_next_device_info(priv, "Product", efuse->device_info, &record_offset);
+	rtl8192eu_log_next_device_info(priv, "Serial", efuse->device_info, &record_offset);
 
 	if (rtl8xxxu_debug & RTL8XXXU_DEBUG_EFUSE) {
 		unsigned char *raw = priv->efuse_wifi.raw;
-- 
2.30.2

[PATCH AUTOSEL 5.4 58/74] iwlwifi: mvm: don't change band on bound PHY contexts

[Sasha Levin]

From: Johannes Berg <johannes.berg@intel.com>

[ Upstream commit 8835a64f74c46baebfc946cd5a2c861b866ebcee ]

When we have a P2P Device active, we attempt to only change the
PHY context it uses when we get a new remain-on-channel, if the
P2P Device is the only user of the PHY context.

This is fine if we're switching within a band, but if we're
switching bands then the switch implies a removal and re-add
of the PHY context, which isn't permitted by the firmware while
it's bound to an interface.

Fix the code to skip the unbind/release/... cycle only if the
band doesn't change (or we have old devices that can switch the
band on the fly as well.)

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210612142637.e9ac313f70f3.I713b9d109957df7e7d9ed0861d5377ce3f8fccd3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../net/wireless/intel/iwlwifi/mvm/mac80211.c | 24 ++++++++++++++-----
 1 file changed, 18 insertions(+), 6 deletions(-)

diff --git a/drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c b/drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c
index fc6430edd110..09b1a6beee77 100644
--- a/drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c
+++ b/drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c
@@ -3725,6 +3725,7 @@ static int iwl_mvm_roc(struct ieee80211_hw *hw,
 	struct iwl_mvm_vif *mvmvif = iwl_mvm_vif_from_mac80211(vif);
 	struct cfg80211_chan_def chandef;
 	struct iwl_mvm_phy_ctxt *phy_ctxt;
+	bool band_change_removal;
 	int ret, i;
 
 	IWL_DEBUG_MAC80211(mvm, "enter (%d, %d, %d)\n", channel->hw_value,
@@ -3794,19 +3795,30 @@ static int iwl_mvm_roc(struct ieee80211_hw *hw,
 	cfg80211_chandef_create(&chandef, channel, NL80211_CHAN_NO_HT);
 
 	/*
-	 * Change the PHY context configuration as it is currently referenced
-	 * only by the P2P Device MAC
+	 * Check if the remain-on-channel is on a different band and that
+	 * requires context removal, see iwl_mvm_phy_ctxt_changed(). If
+	 * so, we'll need to release and then re-configure here, since we
+	 * must not remove a PHY context that's part of a binding.
 	 */
-	if (mvmvif->phy_ctxt->ref == 1) {
+	band_change_removal =
+		fw_has_capa(&mvm->fw->ucode_capa,
+			    IWL_UCODE_TLV_CAPA_BINDING_CDB_SUPPORT) &&
+		mvmvif->phy_ctxt->channel->band != chandef.chan->band;
+
+	if (mvmvif->phy_ctxt->ref == 1 && !band_change_removal) {
+		/*
+		 * Change the PHY context configuration as it is currently
+		 * referenced only by the P2P Device MAC (and we can modify it)
+		 */
 		ret = iwl_mvm_phy_ctxt_changed(mvm, mvmvif->phy_ctxt,
 					       &chandef, 1, 1);
 		if (ret)
 			goto out_unlock;
 	} else {
 		/*
-		 * The PHY context is shared with other MACs. Need to remove the
-		 * P2P Device from the binding, allocate an new PHY context and
-		 * create a new binding
+		 * The PHY context is shared with other MACs (or we're trying to
+		 * switch bands), so remove the P2P Device from the binding,
+		 * allocate an new PHY context and create a new binding.
 		 */
 		phy_ctxt = iwl_mvm_get_free_phy_ctxt(mvm);
 		if (!phy_ctxt) {
-- 
2.30.2

[PATCH AUTOSEL 5.4 59/74] iwlwifi: pcie: free IML DMA memory allocation

[Sasha Levin]

From: Johannes Berg <johannes.berg@intel.com>

[ Upstream commit 310f60f53a86eba680d9bc20a371e13b06a5f903 ]

In the case of gen3 devices with image loader (IML) support,
we were leaking the IML DMA allocation and never freeing it.
Fix that.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618105614.07e117dbedb7.I7bb9ebbe0617656986c2a598ea5e827b533bd3b9@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../wireless/intel/iwlwifi/pcie/ctxt-info-gen3.c  | 15 ++++++++++-----
 .../net/wireless/intel/iwlwifi/pcie/internal.h    |  3 +++
 2 files changed, 13 insertions(+), 5 deletions(-)

diff --git a/drivers/net/wireless/intel/iwlwifi/pcie/ctxt-info-gen3.c b/drivers/net/wireless/intel/iwlwifi/pcie/ctxt-info-gen3.c
index eab159205e48..f6b43cd87d5d 100644
--- a/drivers/net/wireless/intel/iwlwifi/pcie/ctxt-info-gen3.c
+++ b/drivers/net/wireless/intel/iwlwifi/pcie/ctxt-info-gen3.c
@@ -63,7 +63,6 @@ int iwl_pcie_ctxt_info_gen3_init(struct iwl_trans *trans,
 	struct iwl_prph_scratch *prph_scratch;
 	struct iwl_prph_scratch_ctrl_cfg *prph_sc_ctrl;
 	struct iwl_prph_info *prph_info;
-	void *iml_img;
 	u32 control_flags = 0;
 	int ret;
 	int cmdq_size = max_t(u32, IWL_CMD_QUEUE_SIZE,
@@ -162,14 +161,15 @@ int iwl_pcie_ctxt_info_gen3_init(struct iwl_trans *trans,
 	trans_pcie->prph_scratch = prph_scratch;
 
 	/* Allocate IML */
-	iml_img = dma_alloc_coherent(trans->dev, trans->iml_len,
-				     &trans_pcie->iml_dma_addr, GFP_KERNEL);
-	if (!iml_img) {
+	trans_pcie->iml = dma_alloc_coherent(trans->dev, trans->iml_len,
+					     &trans_pcie->iml_dma_addr,
+					     GFP_KERNEL);
+	if (!trans_pcie->iml) {
 		ret = -ENOMEM;
 		goto err_free_ctxt_info;
 	}
 
-	memcpy(iml_img, trans->iml, trans->iml_len);
+	memcpy(trans_pcie->iml, trans->iml, trans->iml_len);
 
 	iwl_enable_fw_load_int_ctx_info(trans);
 
@@ -242,6 +242,11 @@ void iwl_pcie_ctxt_info_gen3_free(struct iwl_trans *trans)
 	trans_pcie->ctxt_info_dma_addr = 0;
 	trans_pcie->ctxt_info_gen3 = NULL;
 
+	dma_free_coherent(trans->dev, trans->iml_len, trans_pcie->iml,
+			  trans_pcie->iml_dma_addr);
+	trans_pcie->iml_dma_addr = 0;
+	trans_pcie->iml = NULL;
+
 	iwl_pcie_ctxt_info_free_fw_img(trans);
 
 	dma_free_coherent(trans->dev, sizeof(*trans_pcie->prph_scratch),
diff --git a/drivers/net/wireless/intel/iwlwifi/pcie/internal.h b/drivers/net/wireless/intel/iwlwifi/pcie/internal.h
index 9b5b96e34456..553164f06a6b 100644
--- a/drivers/net/wireless/intel/iwlwifi/pcie/internal.h
+++ b/drivers/net/wireless/intel/iwlwifi/pcie/internal.h
@@ -475,6 +475,8 @@ struct cont_rec {
  *	Context information addresses will be taken from here.
  *	This is driver's local copy for keeping track of size and
  *	count for allocating and freeing the memory.
+ * @iml: image loader image virtual address
+ * @iml_dma_addr: image loader image DMA address
  * @trans: pointer to the generic transport area
  * @scd_base_addr: scheduler sram base address in SRAM
  * @scd_bc_tbls: pointer to the byte count table of the scheduler
@@ -522,6 +524,7 @@ struct iwl_trans_pcie {
 	};
 	struct iwl_prph_info *prph_info;
 	struct iwl_prph_scratch *prph_scratch;
+	void *iml;
 	dma_addr_t ctxt_info_dma_addr;
 	dma_addr_t prph_info_dma_addr;
 	dma_addr_t prph_scratch_dma_addr;
-- 
2.30.2

[PATCH AUTOSEL 5.4 60/74] iwlwifi: pcie: fix context info freeing

[Sasha Levin]

From: Johannes Berg <johannes.berg@intel.com>

[ Upstream commit 26d18c75a7496c4c52b0b6789e713dc76ebfbc87 ]

After firmware alive, iwl_trans_pcie_gen2_fw_alive() is called
to free the context info. However, on gen3 that will then free
the context info with the wrong size.

Since we free this allocation later, let it stick around until
the device is stopped for now, freeing some of it earlier is a
separate change.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618105614.afb63fb8cbc1.If4968db8e09f4ce2a1d27a6d750bca3d132d7d70@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/intel/iwlwifi/pcie/trans-gen2.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/intel/iwlwifi/pcie/trans-gen2.c b/drivers/net/wireless/intel/iwlwifi/pcie/trans-gen2.c
index df8455f14e4d..ee45e475405a 100644
--- a/drivers/net/wireless/intel/iwlwifi/pcie/trans-gen2.c
+++ b/drivers/net/wireless/intel/iwlwifi/pcie/trans-gen2.c
@@ -269,7 +269,8 @@ void iwl_trans_pcie_gen2_fw_alive(struct iwl_trans *trans, u32 scd_addr)
 	/* now that we got alive we can free the fw image & the context info.
 	 * paging memory cannot be freed included since FW will still use it
 	 */
-	iwl_pcie_ctxt_info_free(trans);
+	if (trans->trans_cfg->device_family < IWL_DEVICE_FAMILY_AX210)
+		iwl_pcie_ctxt_info_free(trans);
 
 	/*
 	 * Re-enable all the interrupts, including the RF-Kill one, now that
-- 
2.30.2

[PATCH AUTOSEL 5.4 63/74] wireless: wext-spy: Fix out-of-bounds warning

[Sasha Levin]

From: "Gustavo A. R. Silva" <gustavoars@kernel.org>

[ Upstream commit e93bdd78406da9ed01554c51e38b2a02c8ef8025 ]

Fix the following out-of-bounds warning:

net/wireless/wext-spy.c:178:2: warning: 'memcpy' offset [25, 28] from the object at 'threshold' is out of the bounds of referenced subobject 'low' with type 'struct iw_quality' at offset 20 [-Warray-bounds]

The problem is that the original code is trying to copy data into a
couple of struct members adjacent to each other in a single call to
memcpy(). This causes a legitimate compiler warning because memcpy()
overruns the length of &threshold.low and &spydata->spy_thr_low. As
these are just a couple of struct members, fix this by using direct
assignments, instead of memcpy().

This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().

Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210422200032.GA168995@embeddedor
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/wireless/wext-spy.c | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)

diff --git a/net/wireless/wext-spy.c b/net/wireless/wext-spy.c
index 33bef22e44e9..b379a0371653 100644
--- a/net/wireless/wext-spy.c
+++ b/net/wireless/wext-spy.c
@@ -120,8 +120,8 @@ int iw_handler_set_thrspy(struct net_device *	dev,
 		return -EOPNOTSUPP;
 
 	/* Just do it */
-	memcpy(&(spydata->spy_thr_low), &(threshold->low),
-	       2 * sizeof(struct iw_quality));
+	spydata->spy_thr_low = threshold->low;
+	spydata->spy_thr_high = threshold->high;
 
 	/* Clear flag */
 	memset(spydata->spy_thr_under, '\0', sizeof(spydata->spy_thr_under));
@@ -147,8 +147,8 @@ int iw_handler_get_thrspy(struct net_device *	dev,
 		return -EOPNOTSUPP;
 
 	/* Just do it */
-	memcpy(&(threshold->low), &(spydata->spy_thr_low),
-	       2 * sizeof(struct iw_quality));
+	threshold->low = spydata->spy_thr_low;
+	threshold->high = spydata->spy_thr_high;
 
 	return 0;
 }
@@ -173,10 +173,10 @@ static void iw_send_thrspy_event(struct net_device *	dev,
 	memcpy(threshold.addr.sa_data, address, ETH_ALEN);
 	threshold.addr.sa_family = ARPHRD_ETHER;
 	/* Copy stats */
-	memcpy(&(threshold.qual), wstats, sizeof(struct iw_quality));
+	threshold.qual = *wstats;
 	/* Copy also thresholds */
-	memcpy(&(threshold.low), &(spydata->spy_thr_low),
-	       2 * sizeof(struct iw_quality));
+	threshold.low = spydata->spy_thr_low;
+	threshold.high = spydata->spy_thr_high;
 
 	/* Send event to user space */
 	wireless_send_event(dev, SIOCGIWTHRSPY, &wrqu, (char *) &threshold);
-- 
2.30.2