From: Jouni Malinen <jouni@codeaurora.org>
To: Kalle Valo <kvalo@codeaurora.org>
Cc: ath11k@lists.infradead.org, linux-wireless@vger.kernel.org,
P Praneesh <ppranees@codeaurora.org>,
Jouni Malinen <jouni@codeaurora.org>
Subject: [PATCH 09/12] ath11k: Add wmi peer create conf event in wmi_tlv_event_id
Date: Thu, 22 Jul 2021 00:20:26 +0300 [thread overview]
Message-ID: <20210721212029.142388-9-jouni@codeaurora.org> (raw)
In-Reply-To: <20210721212029.142388-1-jouni@codeaurora.org>
From: P Praneesh <ppranees@codeaurora.org>
When the driver sends a peer create cmd, the firmware responds with
WMI_PEER_CREATE_CONF_EVENTID to confirm the firmware received
WMI_PEER_CREATE_CMDID. Since the peer create conf event is not handled
in ath11k_wmi_tlv_op_rx, we are getting unknown event id warning prints
during peer creation.
Add WMI_PEER_CREATE_CONF_EVENTID in wmi_tlv_event_id and handle
the same as unsupported event id under wmi logs.
warning prints:
[ 4382.230817] ath11k_pci 0000:01:00.0: Unknown eventid: 0x601a
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
---
drivers/net/wireless/ath/ath11k/wmi.c | 1 +
drivers/net/wireless/ath/ath11k/wmi.h | 3 +++
2 files changed, 4 insertions(+)
diff --git a/drivers/net/wireless/ath/ath11k/wmi.c b/drivers/net/wireless/ath/ath11k/wmi.c
index 020b2b7ee3c8..6d2696db1e07 100644
--- a/drivers/net/wireless/ath/ath11k/wmi.c
+++ b/drivers/net/wireless/ath/ath11k/wmi.c
@@ -7130,6 +7130,7 @@ static void ath11k_wmi_tlv_op_rx(struct ath11k_base *ab, struct sk_buff *skb)
case WMI_TWT_ENABLE_EVENTID:
case WMI_TWT_DISABLE_EVENTID:
case WMI_PDEV_DMA_RING_CFG_RSP_EVENTID:
+ case WMI_PEER_CREATE_CONF_EVENTID:
ath11k_dbg(ab, ATH11K_DBG_WMI,
"ignoring unsupported event 0x%x\n", id);
break;
diff --git a/drivers/net/wireless/ath/ath11k/wmi.h b/drivers/net/wireless/ath/ath11k/wmi.h
index 16b3f48bb378..2587d22f42ce 100644
--- a/drivers/net/wireless/ath/ath11k/wmi.h
+++ b/drivers/net/wireless/ath/ath11k/wmi.h
@@ -663,6 +663,9 @@ enum wmi_tlv_event_id {
WMI_PEER_RESERVED9_EVENTID,
WMI_PEER_RESERVED10_EVENTID,
WMI_PEER_OPER_MODE_CHANGE_EVENTID,
+ WMI_PEER_TX_PN_RESPONSE_EVENTID,
+ WMI_PEER_CFR_CAPTURE_EVENTID,
+ WMI_PEER_CREATE_CONF_EVENTID,
WMI_MGMT_RX_EVENTID = WMI_TLV_CMD(WMI_GRP_MGMT),
WMI_HOST_SWBA_EVENTID,
WMI_TBTTOFFSET_UPDATE_EVENTID,
--
2.25.1
next prev parent reply other threads:[~2021-07-21 21:21 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-07-21 21:20 [PATCH 01/12] ath11k: Fix pktlog lite rx events Jouni Malinen
2021-07-21 21:20 ` [PATCH 02/12] ath11k: Update pdev tx and rx firmware stats Jouni Malinen
2021-07-21 21:20 ` [PATCH 03/12] ath11k: Avoid reg rules update during firmware recovery Jouni Malinen
2021-07-21 21:20 ` [PATCH 04/12] ath11k: Avoid race during regd updates Jouni Malinen
2021-07-21 21:20 ` [PATCH 05/12] ath11k: Add vdev start flag to disable hardware encryption Jouni Malinen
2021-07-21 21:20 ` [PATCH 06/12] ath11k: Assign free_vdev_map value before ieee80211_register_hw Jouni Malinen
2021-07-21 21:20 ` [PATCH 07/12] ath11k: Fix crash during firmware recovery on reo cmd ring access Jouni Malinen
2021-07-21 21:20 ` [PATCH 08/12] ath11k: Avoid "No VIF found" warning message Jouni Malinen
2021-07-21 21:20 ` Jouni Malinen [this message]
2021-07-21 21:20 ` [PATCH 10/12] ath11k: Send PPDU_STATS_CFG with proper pdev mask to firmware Jouni Malinen
2021-09-28 10:46 ` Kalle Valo
2021-09-28 12:01 ` Rameshkumar Sundaram
2021-11-12 8:01 ` Kalle Valo
2021-07-21 21:20 ` [PATCH 11/12] ath11k: Clear auth flag only for actual association in security mode Jouni Malinen
2021-07-21 21:20 ` [PATCH 12/12] ath11k: Change QCN9074 firmware to operate in mode-2 Jouni Malinen
2021-11-12 8:19 ` Kalle Valo
2021-12-08 12:39 ` Anilkumar Kolli
2021-09-28 10:58 ` [PATCH 01/12] ath11k: Fix pktlog lite rx events Kalle Valo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210721212029.142388-9-jouni@codeaurora.org \
--to=jouni@codeaurora.org \
--cc=ath11k@lists.infradead.org \
--cc=kvalo@codeaurora.org \
--cc=linux-wireless@vger.kernel.org \
--cc=ppranees@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).