From: Florian Fainelli <f.fainelli@gmail.com>
To: linux-mtd@lists.infradead.org
Cc: "Florian Fainelli" <f.fainelli@gmail.com>,
"Rafał Miłecki" <zajec5@gmail.com>,
"Miquel Raynal" <miquel.raynal@bootlin.com>,
"Richard Weinberger" <richard@nod.at>,
"Vignesh Raghavendra" <vigneshr@ti.com>,
"Brian Norris" <computersforpeace@gmail.com>,
"Kamal Dasu" <kdasu.kdev@gmail.com>,
"Arnd Bergmann" <arnd@arndb.de>,
"Cai Huoqing" <caihuoqing@baidu.com>,
"Colin Ian King" <colin.king@intel.com>,
linux-kernel@vger.kernel.org (open list),
linux-wireless@vger.kernel.org (open list:BROADCOM SPECIFIC AMBA
DRIVER (BCMA)),
bcm-kernel-feedback-list@broadcom.com (open list:BROADCOM STB
NAND FLASH DRIVER)
Subject: [PATCH v3 9/9] mtd: rawnand: brcmnand: Add BCMA shim
Date: Fri, 7 Jan 2022 10:46:14 -0800 [thread overview]
Message-ID: <20220107184614.2670254-10-f.fainelli@gmail.com> (raw)
In-Reply-To: <20220107184614.2670254-1-f.fainelli@gmail.com>
Add a BCMA shim to allow us to register the brcmnand driver using the
BCMA bus which provides indirect memory mapped access to SoC registers.
There are a number of registers that need to be byte swapped because
they are natively big endian, coming directly from the NAND chip, and
there is no bus interface unlike the iProc or STB platforms that
performs the byte swapping for us.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/mtd/nand/raw/Kconfig | 13 +++
drivers/mtd/nand/raw/brcmnand/Makefile | 2 +
drivers/mtd/nand/raw/brcmnand/bcma_nand.c | 132 ++++++++++++++++++++++
drivers/mtd/nand/raw/brcmnand/brcmnand.c | 4 +
4 files changed, 151 insertions(+)
create mode 100644 drivers/mtd/nand/raw/brcmnand/bcma_nand.c
diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
index 0a45d3c6c15b..7f385ac6e443 100644
--- a/drivers/mtd/nand/raw/Kconfig
+++ b/drivers/mtd/nand/raw/Kconfig
@@ -208,6 +208,19 @@ config MTD_NAND_BRCMNAND
originally designed for Set-Top Box but is used on various BCM7xxx,
BCM3xxx, BCM63xxx, iProc/Cygnus and more.
+if MTD_NAND_BRCMNAND
+
+config MTD_NAND_BRCMNAND_BCMA
+ tristate "Broadcom BCMA NAND controller"
+ depends on BCMA_NFLASH
+ depends on BCMA
+ help
+ Enables the BRCMNAND controller over BCMA on BCM47186/BCM5358 SoCs.
+ The glue driver will take care of performing the low-level I/O
+ operations to interface the BRCMNAND controller over the BCMA bus.
+
+endif # MTD_NAND_BRCMNAND
+
config MTD_NAND_BCM47XXNFLASH
tristate "BCM4706 BCMA NAND controller"
depends on BCMA_NFLASH
diff --git a/drivers/mtd/nand/raw/brcmnand/Makefile b/drivers/mtd/nand/raw/brcmnand/Makefile
index 195b845e48b8..16dc7254200e 100644
--- a/drivers/mtd/nand/raw/brcmnand/Makefile
+++ b/drivers/mtd/nand/raw/brcmnand/Makefile
@@ -6,3 +6,5 @@ obj-$(CONFIG_MTD_NAND_BRCMNAND) += bcm63138_nand.o
obj-$(CONFIG_MTD_NAND_BRCMNAND) += bcm6368_nand.o
obj-$(CONFIG_MTD_NAND_BRCMNAND) += brcmstb_nand.o
obj-$(CONFIG_MTD_NAND_BRCMNAND) += brcmnand.o
+
+obj-$(CONFIG_MTD_NAND_BRCMNAND_BCMA) += bcma_nand.o
diff --git a/drivers/mtd/nand/raw/brcmnand/bcma_nand.c b/drivers/mtd/nand/raw/brcmnand/bcma_nand.c
new file mode 100644
index 000000000000..d7c62988c452
--- /dev/null
+++ b/drivers/mtd/nand/raw/brcmnand/bcma_nand.c
@@ -0,0 +1,132 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright © 2021 Broadcom
+ */
+#include <linux/bcma/bcma.h>
+#include <linux/bcma/bcma_driver_chipcommon.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include "brcmnand.h"
+
+struct brcmnand_bcma_soc {
+ struct brcmnand_soc soc;
+ struct bcma_drv_cc *cc;
+};
+
+static inline bool brcmnand_bcma_needs_swapping(u32 offset)
+{
+ switch (offset) {
+ case BCMA_CC_NAND_SPARE_RD0:
+ case BCMA_CC_NAND_SPARE_RD4:
+ case BCMA_CC_NAND_SPARE_RD8:
+ case BCMA_CC_NAND_SPARE_RD12:
+ case BCMA_CC_NAND_SPARE_WR0:
+ case BCMA_CC_NAND_SPARE_WR4:
+ case BCMA_CC_NAND_SPARE_WR8:
+ case BCMA_CC_NAND_SPARE_WR12:
+ case BCMA_CC_NAND_DEVID:
+ case BCMA_CC_NAND_DEVID_X:
+ case BCMA_CC_NAND_SPARE_RD16:
+ case BCMA_CC_NAND_SPARE_RD20:
+ case BCMA_CC_NAND_SPARE_RD24:
+ case BCMA_CC_NAND_SPARE_RD28:
+ return true;
+ }
+
+ return false;
+}
+
+static inline struct brcmnand_bcma_soc *to_bcma_soc(struct brcmnand_soc *soc)
+{
+ return container_of(soc, struct brcmnand_bcma_soc, soc);
+}
+
+static u32 brcmnand_bcma_read_reg(struct brcmnand_soc *soc, u32 offset)
+{
+ struct brcmnand_bcma_soc *sc = to_bcma_soc(soc);
+ u32 val;
+
+ /* Offset into the NAND block and deal with the flash cache separately */
+ if (offset == BRCMNAND_NON_MMIO_FC_ADDR)
+ offset = BCMA_CC_NAND_CACHE_DATA;
+ else
+ offset += BCMA_CC_NAND_REVISION;
+
+ val = bcma_cc_read32(sc->cc, offset);
+
+ /* Swap if necessary */
+ if (brcmnand_bcma_needs_swapping(offset))
+ val = be32_to_cpu(val);
+ return val;
+}
+
+static void brcmnand_bcma_write_reg(struct brcmnand_soc *soc, u32 val,
+ u32 offset)
+{
+ struct brcmnand_bcma_soc *sc = to_bcma_soc(soc);
+
+ /* Offset into the NAND block */
+ if (offset == BRCMNAND_NON_MMIO_FC_ADDR)
+ offset = BCMA_CC_NAND_CACHE_DATA;
+ else
+ offset += BCMA_CC_NAND_REVISION;
+
+ /* Swap if necessary */
+ if (brcmnand_bcma_needs_swapping(offset))
+ val = cpu_to_be32(val);
+
+ bcma_cc_write32(sc->cc, offset, val);
+}
+
+static struct brcmnand_io_ops brcmnand_bcma_io_ops = {
+ .read_reg = brcmnand_bcma_read_reg,
+ .write_reg = brcmnand_bcma_write_reg,
+};
+
+static void brcmnand_bcma_prepare_data_bus(struct brcmnand_soc *soc, bool prepare,
+ bool is_param)
+{
+ struct brcmnand_bcma_soc *sc = to_bcma_soc(soc);
+
+ /* Reset the cache address to ensure we are already accessing the
+ * beginning of a sub-page.
+ */
+ bcma_cc_write32(sc->cc, BCMA_CC_NAND_CACHE_ADDR, 0);
+}
+
+static int brcmnand_bcma_nand_probe(struct platform_device *pdev)
+{
+ struct bcma_nflash *nflash = dev_get_platdata(&pdev->dev);
+ struct brcmnand_bcma_soc *soc;
+
+ soc = devm_kzalloc(&pdev->dev, sizeof(*soc), GFP_KERNEL);
+ if (!soc)
+ return -ENOMEM;
+
+ soc->cc = container_of(nflash, struct bcma_drv_cc, nflash);
+ soc->soc.prepare_data_bus = brcmnand_bcma_prepare_data_bus;
+ soc->soc.ops = &brcmnand_bcma_io_ops;
+
+ if (soc->cc->core->bus->chipinfo.id == BCMA_CHIP_ID_BCM4706) {
+ dev_err(&pdev->dev, "Use bcm47xxnflash for 4706!\n");
+ return -ENODEV;
+ }
+
+ return brcmnand_probe(pdev, &soc->soc);
+}
+
+static struct platform_driver brcmnand_bcma_nand_driver = {
+ .probe = brcmnand_bcma_nand_probe,
+ .remove = brcmnand_remove,
+ .driver = {
+ .name = "bcma_brcmnand",
+ .pm = &brcmnand_pm_ops,
+ }
+};
+module_platform_driver(brcmnand_bcma_nand_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Broadcom");
+MODULE_DESCRIPTION("NAND controller driver glue for BCMA chips");
diff --git a/drivers/mtd/nand/raw/brcmnand/brcmnand.c b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
index 4759303ece7c..c412f79b81db 100644
--- a/drivers/mtd/nand/raw/brcmnand/brcmnand.c
+++ b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
@@ -598,7 +598,11 @@ enum {
static inline bool brcmnand_non_mmio_ops(struct brcmnand_controller *ctrl)
{
+#if IS_ENABLED(CONFIG_MTD_NAND_BRCMNAND_BCMA)
return static_branch_unlikely(&brcmnand_soc_has_ops_key);
+#else
+ return false;
+#endif
}
static inline u32 nand_readreg(struct brcmnand_controller *ctrl, u32 offs)
--
2.25.1
next prev parent reply other threads:[~2022-01-07 18:46 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-01-07 18:46 [PATCH v3 0/9] BCMA support for brcmnand Florian Fainelli
2022-01-07 18:46 ` [PATCH v3 1/9] mtd: rawnand: brcmnand: Assign soc as early as possible Florian Fainelli
2022-01-07 18:46 ` [PATCH v3 2/9] mtd: rawnand: brcmnand: Allow SoC to provide I/O operations Florian Fainelli
2022-01-07 18:46 ` [PATCH v3 3/9] mtd: rawnand: brcmnand: Avoid pdev in brcmnand_init_cs() Florian Fainelli
2022-01-07 18:46 ` [PATCH v3 4/9] mtd: rawnand: brcmnand: Move OF operations out of brcmnand_init_cs() Florian Fainelli
2022-01-07 18:46 ` [PATCH v3 5/9] mtd: rawnand: brcmnand: Allow working without interrupts Florian Fainelli
2022-01-07 18:46 ` [PATCH v3 6/9] mtd: rawnand: brcmnand: Add platform data structure for BCMA Florian Fainelli
2022-01-07 18:46 ` [PATCH v3 7/9] mtd: rawnand: brcmnand: Allow platform data instantation Florian Fainelli
2022-01-07 18:46 ` [PATCH v3 8/9] mtd: rawnand: brcmnand: BCMA controller uses command shift of 0 Florian Fainelli
2022-01-07 18:46 ` Florian Fainelli [this message]
2022-01-10 17:38 ` [PATCH v3 0/9] BCMA support for brcmnand Kamal Dasu
2022-01-23 15:42 ` Miquel Raynal
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220107184614.2670254-10-f.fainelli@gmail.com \
--to=f.fainelli@gmail.com \
--cc=arnd@arndb.de \
--cc=bcm-kernel-feedback-list@broadcom.com \
--cc=caihuoqing@baidu.com \
--cc=colin.king@intel.com \
--cc=computersforpeace@gmail.com \
--cc=kdasu.kdev@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=linux-wireless@vger.kernel.org \
--cc=miquel.raynal@bootlin.com \
--cc=richard@nod.at \
--cc=vigneshr@ti.com \
--cc=zajec5@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).