linux-wireless.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Kalle Valo <kvalo@kernel.org>
To: ath12k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Subject: [PATCH RFC v3 1/6] wifi: ath12k: fix atomic calls in ath12k_mac_op_set_bitrate_mask()
Date: Tue, 24 Sep 2024 12:25:10 +0300	[thread overview]
Message-ID: <20240924092515.1049885-2-kvalo@kernel.org> (raw)
In-Reply-To: <20240924092515.1049885-1-kvalo@kernel.org>

From: Kalle Valo <quic_kvalo@quicinc.com>

When I try to manually set bitrates:

iw wlan0 set bitrates legacy-2.4 1

I get sleeping from invalid context error, see below. Fix that by switching to
use recently introduced ieee80211_iterate_stations_mtx().

Do note that WCN6855 firmware is still crashing, I'm not sure if that firmware
even supports bitrate WMI commands and should we consider disabling
ath12k_mac_op_set_bitrate_mask() for WCN6855? But that's for another patch.

BUG: sleeping function called from invalid context at drivers/net/wireless/ath/ath12k/wmi.c:420
in_atomic(): 0, irqs_disabled(): 0, non_block: 0, pid: 2236, name: iw
preempt_count: 0, expected: 0
RCU nest depth: 1, expected: 0
3 locks held by iw/2236:
 #0: ffffffffabc6f1d8 (cb_lock){++++}-{3:3}, at: genl_rcv+0x14/0x40
 #1: ffff888138410810 (&rdev->wiphy.mtx){+.+.}-{3:3}, at: nl80211_pre_doit+0x54d/0x800 [cfg80211]
 #2: ffffffffab2cfaa0 (rcu_read_lock){....}-{1:2}, at: ieee80211_iterate_stations_atomic+0x2f/0x200 [mac80211]
CPU: 3 UID: 0 PID: 2236 Comm: iw Not tainted 6.11.0-rc7-wt-ath+ #1772
Hardware name: Intel(R) Client Systems NUC8i7HVK/NUC8i7HVB, BIOS HNKBLi70.86A.0067.2021.0528.1339 05/28/2021
Call Trace:
 <TASK>
 dump_stack_lvl+0xa4/0xe0
 dump_stack+0x10/0x20
 __might_resched+0x363/0x5a0
 ? __alloc_skb+0x165/0x340
 __might_sleep+0xad/0x160
 ath12k_wmi_cmd_send+0xb1/0x3d0 [ath12k]
 ? ath12k_wmi_init_wcn7850+0xa40/0xa40 [ath12k]
 ? __netdev_alloc_skb+0x45/0x7b0
 ? __asan_memset+0x39/0x40
 ? ath12k_wmi_alloc_skb+0xf0/0x150 [ath12k]
 ? reacquire_held_locks+0x4d0/0x4d0
 ath12k_wmi_set_peer_param+0x340/0x5b0 [ath12k]
 ath12k_mac_disable_peer_fixed_rate+0xa3/0x110 [ath12k]
 ? ath12k_mac_vdev_stop+0x4f0/0x4f0 [ath12k]
 ieee80211_iterate_stations_atomic+0xd4/0x200 [mac80211]
 ath12k_mac_op_set_bitrate_mask+0x5d2/0x1080 [ath12k]
 ? ath12k_mac_vif_chan+0x320/0x320 [ath12k]
 drv_set_bitrate_mask+0x267/0x470 [mac80211]
 ieee80211_set_bitrate_mask+0x4cc/0x8a0 [mac80211]
 ? __this_cpu_preempt_check+0x13/0x20
 nl80211_set_tx_bitrate_mask+0x2bc/0x530 [cfg80211]
 ? nl80211_parse_tx_bitrate_mask+0x2320/0x2320 [cfg80211]
 ? trace_contention_end+0xef/0x140
 ? rtnl_unlock+0x9/0x10
 ? nl80211_pre_doit+0x557/0x800 [cfg80211]
 genl_family_rcv_msg_doit+0x1f0/0x2e0
 ? genl_family_rcv_msg_attrs_parse.isra.0+0x250/0x250
 ? ns_capable+0x57/0xd0
 genl_family_rcv_msg+0x34c/0x600
 ? genl_family_rcv_msg_dumpit+0x310/0x310
 ? __lock_acquire+0xc62/0x1de0
 ? he_set_mcs_mask.isra.0+0x8d0/0x8d0 [cfg80211]
 ? nl80211_parse_tx_bitrate_mask+0x2320/0x2320 [cfg80211]
 ? cfg80211_external_auth_request+0x690/0x690 [cfg80211]
 genl_rcv_msg+0xa0/0x130
 netlink_rcv_skb+0x14c/0x400
 ? genl_family_rcv_msg+0x600/0x600
 ? netlink_ack+0xd70/0xd70
 ? rwsem_optimistic_spin+0x4f0/0x4f0
 ? genl_rcv+0x14/0x40
 ? down_read_killable+0x580/0x580
 ? netlink_deliver_tap+0x13e/0x350
 ? __this_cpu_preempt_check+0x13/0x20
 genl_rcv+0x23/0x40
 netlink_unicast+0x45e/0x790
 ? netlink_attachskb+0x7f0/0x7f0
 netlink_sendmsg+0x7eb/0xdb0
 ? netlink_unicast+0x790/0x790
 ? __this_cpu_preempt_check+0x13/0x20
 ? selinux_socket_sendmsg+0x31/0x40
 ? netlink_unicast+0x790/0x790
 __sock_sendmsg+0xc9/0x160
 ____sys_sendmsg+0x620/0x990
 ? kernel_sendmsg+0x30/0x30
 ? __copy_msghdr+0x410/0x410
 ? __kasan_check_read+0x11/0x20
 ? mark_lock+0xe6/0x1470
 ___sys_sendmsg+0xe9/0x170
 ? copy_msghdr_from_user+0x120/0x120
 ? __lock_acquire+0xc62/0x1de0
 ? do_fault_around+0x2c6/0x4e0
 ? do_user_addr_fault+0x8c1/0xde0
 ? reacquire_held_locks+0x220/0x4d0
 ? do_user_addr_fault+0x8c1/0xde0
 ? __kasan_check_read+0x11/0x20
 ? __fdget+0x4e/0x1d0
 ? sockfd_lookup_light+0x1a/0x170
 __sys_sendmsg+0xd2/0x180
 ? __sys_sendmsg_sock+0x20/0x20
 ? reacquire_held_locks+0x4d0/0x4d0
 ? debug_smp_processor_id+0x17/0x20
 __x64_sys_sendmsg+0x72/0xb0
 ? lockdep_hardirqs_on+0x7d/0x100
 x64_sys_call+0x894/0x9f0
 do_syscall_64+0x64/0x130
 entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x7f230fe04807
Code: 64 89 02 48 c7 c0 ff ff ff ff eb bb 0f 1f 80 00 00 00 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 89 54 24 1c 48 89 74 24 10
RSP: 002b:00007ffe996a7ea8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000556f9f9c3390 RCX: 00007f230fe04807
RDX: 0000000000000000 RSI: 00007ffe996a7ee0 RDI: 0000000000000003
RBP: 0000556f9f9c88c0 R08: 0000000000000002 R09: 0000000000000000
R10: 0000556f965ca190 R11: 0000000000000246 R12: 0000556f9f9c8780
R13: 00007ffe996a7ee0 R14: 0000556f9f9c87d0 R15: 0000556f9f9c88c0
 </TASK>

Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3

Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
---
 drivers/net/wireless/ath/ath12k/mac.c | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)

diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index 137394c36460..47f9a936b697 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -8183,9 +8183,9 @@ ath12k_mac_op_set_bitrate_mask(struct ieee80211_hw *hw,
 				    arvif->vdev_id, ret);
 			goto out;
 		}
-		ieee80211_iterate_stations_atomic(hw,
-						  ath12k_mac_disable_peer_fixed_rate,
-						  arvif);
+		ieee80211_iterate_stations_mtx(hw,
+					       ath12k_mac_disable_peer_fixed_rate,
+					       arvif);
 	} else if (ath12k_mac_bitrate_mask_get_single_nss(ar, band, mask,
 							  &single_nss)) {
 		rate = WMI_FIXED_RATE_NONE;
@@ -8230,16 +8230,16 @@ ath12k_mac_op_set_bitrate_mask(struct ieee80211_hw *hw,
 			goto out;
 		}
 
-		ieee80211_iterate_stations_atomic(hw,
-						  ath12k_mac_disable_peer_fixed_rate,
-						  arvif);
+		ieee80211_iterate_stations_mtx(hw,
+					       ath12k_mac_disable_peer_fixed_rate,
+					       arvif);
 
 		mutex_lock(&ar->conf_mutex);
 
 		arvif->bitrate_mask = *mask;
-		ieee80211_iterate_stations_atomic(hw,
-						  ath12k_mac_set_bitrate_mask_iter,
-						  arvif);
+		ieee80211_iterate_stations_mtx(hw,
+					       ath12k_mac_set_bitrate_mask_iter,
+					       arvif);
 
 		mutex_unlock(&ar->conf_mutex);
 	}
-- 
2.39.5


  reply	other threads:[~2024-09-24  9:25 UTC|newest]

Thread overview: 8+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2024-09-24  9:25 [PATCH RFC v3 0/6] wifi: ath12k: switch to using wiphy_lock() Kalle Valo
2024-09-24  9:25 ` Kalle Valo [this message]
2024-09-24  9:25 ` [PATCH RFC v3 2/6] wifi: ath12k: convert struct ath12k_sta::update_wk to use struct wiphy_work Kalle Valo
2024-09-24  9:25 ` [PATCH RFC v3 3/6] wifi: ath12k: switch to using wiphy_lock() and remove ar->conf_mutex Kalle Valo
2024-10-07 14:47   ` Kalle Valo
2024-09-24  9:25 ` [PATCH RFC v3 4/6] wifi: ath12k: cleanup unneeded labels Kalle Valo
2024-09-24  9:25 ` [PATCH RFC v3 5/6] wifi: ath12k: ath12k_mac_op_set_key(): remove exit label Kalle Valo
2024-09-24  9:25 ` [PATCH RFC v3 6/6] wifi: ath12k: ath12k_mac_op_sta_state(): clean up update_wk cancellation Kalle Valo

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20240924092515.1049885-2-kvalo@kernel.org \
    --to=kvalo@kernel.org \
    --cc=ath12k@lists.infradead.org \
    --cc=linux-wireless@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).