[PATCH v5 5/6] wifi: rtw88: sdio: set up RX aggregation and interrupts for RTL8723BS

[luka.gejak@linux.dev]

From: Luka Gejak <luka.gejak@linux.dev>

Enable the existing RX aggregation setup for this chip and select the
larger DMA burst count it needs. The RTL8723BS does not raise CPWM1, so
leave that source out of its interrupt mask, and set the SDIO TX control
bit the vendor driver uses to have transfers always recognised.

The chip was also seen to keep raising the interrupt after resume when
undefined status bits were written back on acknowledgment, so
acknowledge only the bits this driver defines. That observation dates
from bring up and I cannot re-measure it: the test machine only offers
s2idle and does not reliably return from it, so the resume path is not
exercised here. The change is scoped to this chip; the other SDIO parts
keep writing the status word back unchanged.

Signed-off-by: Luka Gejak <luka.gejak@linux.dev>
---
 drivers/net/wireless/realtek/rtw88/sdio.c | 28 ++++++++++++++++++++++-
 drivers/net/wireless/realtek/rtw88/sdio.h |  9 ++++++++
 2 files changed, 36 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/realtek/rtw88/sdio.c b/drivers/net/wireless/realtek/rtw88/sdio.c
index a8209b9acefd..eaec776dd943 100644
--- a/drivers/net/wireless/realtek/rtw88/sdio.c
+++ b/drivers/net/wireless/realtek/rtw88/sdio.c
@@ -903,7 +903,11 @@ static void rtw_sdio_init(struct rtw_dev *rtwdev)
 {
 	struct rtw_sdio *rtwsdio = (struct rtw_sdio *)rtwdev->priv;
 
-	rtwsdio->irq_mask = REG_SDIO_HIMR_RX_REQUEST | REG_SDIO_HIMR_CPWM1;
+	if (rtw_is_8723bs(rtwdev))
+		rtwsdio->irq_mask = REG_SDIO_HIMR_RX_REQUEST;
+	else
+		rtwsdio->irq_mask = REG_SDIO_HIMR_RX_REQUEST |
+				    REG_SDIO_HIMR_CPWM1;
 }
 
 static void rtw_sdio_enable_rx_aggregation(struct rtw_dev *rtwdev)
@@ -911,6 +915,7 @@ static void rtw_sdio_enable_rx_aggregation(struct rtw_dev *rtwdev)
 	u8 size, timeout;
 
 	switch (rtwdev->chip->id) {
+	case RTW_CHIP_TYPE_8723B:
 	case RTW_CHIP_TYPE_8703B:
 	case RTW_CHIP_TYPE_8821A:
 	case RTW_CHIP_TYPE_8812A:
@@ -938,6 +943,8 @@ static void rtw_sdio_enable_rx_aggregation(struct rtw_dev *rtwdev)
 		    FIELD_PREP(BIT_DMA_AGG_TO_V1, timeout));
 
 	rtw_write8_set(rtwdev, REG_RXDMA_MODE, BIT_DMA_MODE);
+	if (rtw_is_8723bs(rtwdev))
+		rtw_write8_mask(rtwdev, REG_RXDMA_MODE, BIT_DMA_BURST_CNT, 0x3);
 }
 
 static void rtw_sdio_enable_interrupt(struct rtw_dev *rtwdev)
@@ -1009,6 +1016,8 @@ static int rtw_sdio_8723bs_check_rqpn(struct rtw_dev *rtwdev)
 
 static int rtw_sdio_start(struct rtw_dev *rtwdev)
 {
+	u32 clear;
+
 	if (rtw_is_8723bs(rtwdev)) {
 		int ret = rtw_sdio_8723bs_check_rqpn(rtwdev);
 
@@ -1021,6 +1030,13 @@ static int rtw_sdio_start(struct rtw_dev *rtwdev)
 	}
 
 	rtw_sdio_enable_rx_aggregation(rtwdev);
+
+	if (rtw_is_8723bs(rtwdev)) {
+		clear = rtw_read32(rtwdev, REG_SDIO_HISR) & RTW_SDIO_HISR_CLEAR_MASK;
+		if (clear)
+			rtw_write32(rtwdev, REG_SDIO_HISR, clear);
+	}
+
 	rtw_sdio_enable_interrupt(rtwdev);
 
 	return 0;
@@ -1100,6 +1116,8 @@ static void rtw_sdio_interface_cfg(struct rtw_dev *rtwdev)
 
 	val = rtw_read32(rtwdev, REG_SDIO_TX_CTRL);
 	val &= 0xfff8;
+	if (rtw_is_8723bs(rtwdev))
+		val |= BIT_SDIO_TX_CTRL_ALWAYS_RECOGNIZE;
 	rtw_write32(rtwdev, REG_SDIO_TX_CTRL, val);
 }
 
@@ -1364,6 +1382,14 @@ static void rtw_sdio_handle_interrupt(struct sdio_func *sdio_func)
 		rtw_sdio_rx_isr(rtwdev);
 	}
 
+	/*
+	 * RTL8723BS keeps raising the interrupt after resume if undefined
+	 * status bits are written back, so acknowledge only the bits this
+	 * driver defines. Other chips keep the existing behaviour.
+	 */
+	if (rtw_is_8723bs(rtwdev))
+		hisr &= RTW_SDIO_HISR_CLEAR_MASK;
+
 	rtw_write32(rtwdev, REG_SDIO_HISR, hisr);
 
 	rtwsdio->irq_thread = NULL;
diff --git a/drivers/net/wireless/realtek/rtw88/sdio.h b/drivers/net/wireless/realtek/rtw88/sdio.h
index 5b000cb8fac2..7474a7511811 100644
--- a/drivers/net/wireless/realtek/rtw88/sdio.h
+++ b/drivers/net/wireless/realtek/rtw88/sdio.h
@@ -22,6 +22,7 @@
 
 /* SDIO Tx Control */
 #define REG_SDIO_TX_CTRL			(SDIO_LOCAL_OFFSET + 0x0000)
+#define BIT_SDIO_TX_CTRL_ALWAYS_RECOGNIZE	BIT(4)
 
 /*SDIO status timeout*/
 #define REG_SDIO_TIMEOUT			(SDIO_LOCAL_OFFSET + 0x0002)
@@ -77,6 +78,14 @@
 /* the following two are RTL8188 SDIO Specific */
 #define REG_SDIO_HISR_MCU_ERR			BIT(28)
 #define REG_SDIO_HISR_TSF_BIT32_TOGGLE		BIT(29)
+#define RTW_SDIO_HISR_CLEAR_MASK		\
+	(REG_SDIO_HISR_TXERR | REG_SDIO_HISR_RXERR | \
+	 REG_SDIO_HISR_TXFOVW | REG_SDIO_HISR_RXFOVW | \
+	 REG_SDIO_HISR_TXBCNOK | REG_SDIO_HISR_TXBCNERR | \
+	 REG_SDIO_HISR_C2HCMD | REG_SDIO_HISR_CPWM1 | \
+	 REG_SDIO_HISR_CPWM2 | REG_SDIO_HISR_HSISR_IND | \
+	 REG_SDIO_HISR_GTINT3_IND | REG_SDIO_HISR_GTINT4_IND | \
+	 REG_SDIO_HISR_PSTIMEOUT | REG_SDIO_HISR_OCPINT)
 
 /* HCI Current Power Mode */
 #define REG_SDIO_HCPWM				(SDIO_LOCAL_OFFSET + 0x0019)
-- 
2.53.0