From: Felix Fietkau <nbd@nbd.name>
To: linux-wireless@vger.kernel.org
Subject: [PATCH mt76-next 09/25] wifi: mt76: mt7996: factor the vif link teardown out of remove_interface
Date: Wed, 28 Oct 2026 13:23:47 +0100 [thread overview]
Message-ID: <20261028122403.796394-9-nbd@nbd.name> (raw)
In-Reply-To: <20261028122403.796394-1-nbd@nbd.name>
Move the loop that destroys the links of a vif out of
mt7996_remove_interface() into a helper that takes the links to destroy
and, optionally, their link confs. A following change destroys station
links when the vif leaves MLO, where mac80211 still passes the old link
confs.
No functional change.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
.../net/wireless/mediatek/mt76/mt7996/main.c | 47 +++++++++++--------
1 file changed, 28 insertions(+), 19 deletions(-)
diff --git a/drivers/net/wireless/mediatek/mt76/mt7996/main.c b/drivers/net/wireless/mediatek/mt76/mt7996/main.c
index 3a3441951254..cc8ce83f8b2d 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7996/main.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7996/main.c
@@ -471,6 +471,33 @@ static void mt7996_vif_link_destroy(struct mt7996_phy *phy,
}
}
+static void
+mt7996_vif_links_destroy(struct mt7996_dev *dev, struct ieee80211_vif *vif,
+ unsigned long links,
+ struct ieee80211_bss_conf **link_confs)
+{
+ unsigned int link_id;
+
+ for_each_set_bit(link_id, &links, IEEE80211_MLD_MAX_NUM_LINKS) {
+ struct ieee80211_bss_conf *link_conf = NULL;
+ struct mt7996_vif_link *link;
+ struct mt7996_phy *phy;
+
+ link = mt7996_vif_link(dev, vif, link_id);
+ if (!link)
+ continue;
+
+ phy = __mt7996_phy(dev, link->msta_link.wcid.phy_idx);
+ if (!phy)
+ continue;
+
+ if (link_confs)
+ link_conf = link_confs[link_id];
+
+ mt7996_vif_link_destroy(phy, link, vif, link_conf);
+ }
+}
+
void mt7996_vif_link_remove(struct mt76_phy *mphy, struct ieee80211_vif *vif,
struct ieee80211_bss_conf *link_conf,
struct mt76_vif_link *mlink)
@@ -640,30 +667,12 @@ static void mt7996_remove_interface(struct ieee80211_hw *hw,
struct ieee80211_vif *vif)
{
struct mt7996_vif *mvif = (struct mt7996_vif *)vif->drv_priv;
- unsigned long rem_links = mvif->mt76.valid_links;
struct mt7996_dev *dev = mt7996_hw_dev(hw);
struct mt7996_radio_data rdata = {};
- unsigned int link_id;
int i;
mutex_lock(&dev->mt76.mutex);
-
- /* Remove all active links */
- for_each_set_bit(link_id, &rem_links, IEEE80211_MLD_MAX_NUM_LINKS) {
- struct mt7996_vif_link *link;
- struct mt7996_phy *phy;
-
- link = mt7996_vif_link(dev, vif, link_id);
- if (!link)
- continue;
-
- phy = __mt7996_phy(dev, link->msta_link.wcid.phy_idx);
- if (!phy)
- continue;
-
- mt7996_vif_link_destroy(phy, link, vif, NULL);
- }
-
+ mt7996_vif_links_destroy(dev, vif, mvif->mt76.valid_links, NULL);
mutex_unlock(&dev->mt76.mutex);
ieee80211_iterate_active_interfaces_mtx(hw, 0, mt7996_remove_iter,
--
2.47.3
next prev parent reply other threads:[~2026-10-28 12:24 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-10-28 12:23 [PATCH mt76-next 01/25] wifi: mt76: mt7996: take the link of an 802.3 frame from its station Felix Fietkau
2026-10-28 12:23 ` [PATCH mt76-next 02/25] wifi: mt76: mt7996: do not update beacons while CSA is active Felix Fietkau
2026-10-28 12:23 ` [PATCH mt76-next 03/25] wifi: mt76: mt7996: only remove a BMC STA_REC that was added Felix Fietkau
2026-10-28 12:23 ` [PATCH mt76-next 04/25] wifi: mt76: mt7996: pass the puncturing bitmap to the firmware Felix Fietkau
2026-10-28 12:23 ` [PATCH mt76-next 05/25] wifi: mt76: abort a scan when the chanctx changes Felix Fietkau
2026-10-28 12:23 ` [PATCH mt76-next 06/25] wifi: mt76: set the channel again when the chanctx puncturing changes Felix Fietkau
2026-10-28 12:23 ` [PATCH mt76-next 07/25] wifi: mt76: mt7996: advertise preamble puncturing support Felix Fietkau
2026-10-28 12:23 ` [PATCH mt76-next 08/25] wifi: mt76: mt7996: keep scan and ROC links out of the MLD group Felix Fietkau
2026-10-28 12:23 ` Felix Fietkau [this message]
2026-10-28 12:23 ` [PATCH mt76-next 10/25] wifi: mt76: mt7996: destroy station links before the MLD group is freed Felix Fietkau
2026-10-28 12:23 ` [PATCH mt76-next 11/25] wifi: mt76: mt7996: send MLD link operations for an AP MLD only Felix Fietkau
2026-10-28 12:23 ` [PATCH mt76-next 12/25] wifi: mt76: mt7996: set up a vif link again on another radio Felix Fietkau
2026-10-28 12:23 ` [PATCH mt76-next 13/25] wifi: mt76: mt7996: describe an MLD peer with the PEER_MLD command Felix Fietkau
2026-10-28 12:23 ` [PATCH mt76-next 14/25] wifi: mt76: mt7915: honour the valid flag in efuse block reads Felix Fietkau
2026-10-28 12:23 ` [PATCH mt76-next 15/25] wifi: mt76: mt7996: skip MLD address translation for encap offload frames Felix Fietkau
2026-10-28 12:23 ` [PATCH mt76-next 16/25] wifi: mt76: mt7921: honour the valid flag in efuse block reads Felix Fietkau
2026-10-28 12:23 ` [PATCH mt76-next 17/25] wifi: mt76: mt7915: upload the CSA beacon only once Felix Fietkau
2026-10-28 12:23 ` [PATCH mt76-next 18/25] wifi: mt76: read the chanctx of a link once Felix Fietkau
2026-10-28 12:23 ` [PATCH mt76-next 19/25] wifi: mt76: restart the beacon monitor of a link that gets a chanctx again Felix Fietkau
2026-10-28 12:23 ` [PATCH mt76-next 20/25] wifi: mt76: publish the beacon monitor interval after its timestamp Felix Fietkau
2026-10-28 12:23 ` [PATCH mt76-next 21/25] wifi: mt76: mt7996: keep rx header translation off while a monitor runs Felix Fietkau
2026-10-28 12:24 ` [PATCH mt76-next 22/25] wifi: mt76: mt7996: apply monitor mode again after a full reset Felix Fietkau
2026-10-28 12:24 ` [PATCH mt76-next 23/25] wifi: mt76: check the RX PN of an MLD peer once per peer Felix Fietkau
2026-10-28 12:24 ` [PATCH mt76-next 24/25] wifi: mt76: mt7996: send no MLD_SETUP when station links only go away Felix Fietkau
2026-10-28 12:24 ` [PATCH mt76-next 25/25] wifi: mt76: mt7996: keep a unicast management frame on its MLO link Felix Fietkau
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261028122403.796394-9-nbd@nbd.name \
--to=nbd@nbd.name \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox