From: Sujith Manoharan <c_manoha@qca.qualcomm.com>
To: <linville@tuxdriver.com>
Cc: <linux-wireless@vger.kernel.org>
Subject: [PATCH 04/12] ath9k: Simplify ASSOC handling
Date: Tue, 17 Jul 2012 17:15:50 +0530 [thread overview]
Message-ID: <20485.20590.137366.956003@gargle.gargle.HOWL> (raw)
Cleanup the messy logic dealing with station association
and disassociation.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
---
drivers/net/wireless/ath/ath9k/beacon.c | 2 +-
drivers/net/wireless/ath/ath9k/main.c | 118 +++++++++++++-------------------
2 files changed, 49 insertions(+), 71 deletions(-)
diff --git a/drivers/net/wireless/ath/ath9k/beacon.c b/drivers/net/wireless/ath/ath9k/beacon.c
index d357002..351ded5 100644
--- a/drivers/net/wireless/ath/ath9k/beacon.c
+++ b/drivers/net/wireless/ath/ath9k/beacon.c
@@ -472,7 +472,7 @@ static void ath_beacon_config_sta(struct ath_softc *sc,
int num_beacons, offset, dtim_dec_count, cfp_dec_count;
/* No need to configure beacon if we are not associated */
- if (!common->curaid) {
+ if (!test_bit(SC_OP_PRIM_STA_VIF, &sc->sc_flags)) {
ath_dbg(common, BEACON,
"STA is not yet associated..skipping beacon config\n");
return;
diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c
index d4060ec..80348d8 100644
--- a/drivers/net/wireless/ath/ath9k/main.c
+++ b/drivers/net/wireless/ath/ath9k/main.c
@@ -1430,86 +1430,53 @@ static int ath9k_set_key(struct ieee80211_hw *hw,
return ret;
}
-static void ath9k_bss_iter(void *data, u8 *mac, struct ieee80211_vif *vif)
+
+static void ath9k_set_assoc_state(struct ath_softc *sc,
+ struct ieee80211_vif *vif)
{
- struct ath_softc *sc = data;
struct ath_common *common = ath9k_hw_common(sc->sc_ah);
- struct ieee80211_bss_conf *bss_conf = &vif->bss_conf;
struct ath_vif *avp = (void *)vif->drv_priv;
+ struct ieee80211_bss_conf *bss_conf = &vif->bss_conf;
unsigned long flags;
+
+ set_bit(SC_OP_PRIM_STA_VIF, &sc->sc_flags);
+ avp->primary_sta_vif = true;
+
/*
- * Skip iteration if primary station vif's bss info
- * was not changed
+ * Set the AID, BSSID and do beacon-sync only when
+ * the HW opmode is STATION.
+ *
+ * But the primary bit is set above in any case.
*/
- if (test_bit(SC_OP_PRIM_STA_VIF, &sc->sc_flags))
+ if (sc->sc_ah->opmode != NL80211_IFTYPE_STATION)
return;
- if (bss_conf->assoc) {
- set_bit(SC_OP_PRIM_STA_VIF, &sc->sc_flags);
- avp->primary_sta_vif = true;
- memcpy(common->curbssid, bss_conf->bssid, ETH_ALEN);
- common->curaid = bss_conf->aid;
- ath9k_hw_write_associd(sc->sc_ah);
- ath_dbg(common, CONFIG, "Bss Info ASSOC %d, bssid: %pM\n",
- bss_conf->aid, common->curbssid);
- ath_beacon_config(sc, vif);
- /*
- * Request a re-configuration of Beacon related timers
- * on the receipt of the first Beacon frame (i.e.,
- * after time sync with the AP).
- */
- spin_lock_irqsave(&sc->sc_pm_lock, flags);
- sc->ps_flags |= PS_BEACON_SYNC | PS_WAIT_FOR_BEACON;
- spin_unlock_irqrestore(&sc->sc_pm_lock, flags);
-
- /* Reset rssi stats */
- sc->last_rssi = ATH_RSSI_DUMMY_MARKER;
- sc->sc_ah->stats.avgbrssi = ATH_RSSI_DUMMY_MARKER;
+ memcpy(common->curbssid, bss_conf->bssid, ETH_ALEN);
+ common->curaid = bss_conf->aid;
+ ath9k_hw_write_associd(sc->sc_ah);
- ath_start_rx_poll(sc, 3);
+ sc->last_rssi = ATH_RSSI_DUMMY_MARKER;
+ sc->sc_ah->stats.avgbrssi = ATH_RSSI_DUMMY_MARKER;
- if (!common->disable_ani) {
- set_bit(SC_OP_ANI_RUN, &sc->sc_flags);
- ath_start_ani(common);
- }
+ spin_lock_irqsave(&sc->sc_pm_lock, flags);
+ sc->ps_flags |= PS_BEACON_SYNC | PS_WAIT_FOR_BEACON;
+ spin_unlock_irqrestore(&sc->sc_pm_lock, flags);
- }
+ ath_dbg(common, CONFIG,
+ "Primary Station interface: %pM, BSSID: %pM\n",
+ vif->addr, common->curbssid);
}
-static void ath9k_config_bss(struct ath_softc *sc, struct ieee80211_vif *vif)
+static void ath9k_bss_assoc_iter(void *data, u8 *mac, struct ieee80211_vif *vif)
{
- struct ath_common *common = ath9k_hw_common(sc->sc_ah);
+ struct ath_softc *sc = data;
struct ieee80211_bss_conf *bss_conf = &vif->bss_conf;
- struct ath_vif *avp = (void *)vif->drv_priv;
- if (sc->sc_ah->opmode != NL80211_IFTYPE_STATION)
+ if (test_bit(SC_OP_PRIM_STA_VIF, &sc->sc_flags))
return;
- /* Reconfigure bss info */
- if (avp->primary_sta_vif && !bss_conf->assoc) {
- ath_dbg(common, CONFIG, "Bss Info DISASSOC %d, bssid %pM\n",
- common->curaid, common->curbssid);
- clear_bit(SC_OP_PRIM_STA_VIF, &sc->sc_flags);
- clear_bit(SC_OP_BEACONS, &sc->sc_flags);
- avp->primary_sta_vif = false;
- memset(common->curbssid, 0, ETH_ALEN);
- common->curaid = 0;
- }
-
- ieee80211_iterate_active_interfaces_atomic(
- sc->hw, ath9k_bss_iter, sc);
-
- /*
- * None of station vifs are associated.
- * Clear bssid & aid
- */
- if (!test_bit(SC_OP_PRIM_STA_VIF, &sc->sc_flags)) {
- ath9k_hw_write_associd(sc->sc_ah);
- clear_bit(SC_OP_ANI_RUN, &sc->sc_flags);
- del_timer_sync(&common->ani.timer);
- del_timer_sync(&sc->rx_poll_timer);
- memset(&sc->caldata, 0, sizeof(sc->caldata));
- }
+ if (bss_conf->assoc)
+ ath9k_set_assoc_state(sc, vif);
}
static void ath9k_bss_info_changed(struct ieee80211_hw *hw,
@@ -1527,30 +1494,41 @@ static void ath9k_bss_info_changed(struct ieee80211_hw *hw,
mutex_lock(&sc->mutex);
if (changed & BSS_CHANGED_ASSOC) {
- ath9k_config_bss(sc, vif);
+ ath_dbg(common, CONFIG, "BSSID %pM Changed ASSOC %d\n",
+ bss_conf->bssid, bss_conf->assoc);
+
+ if (avp->primary_sta_vif && !bss_conf->assoc) {
+ clear_bit(SC_OP_PRIM_STA_VIF, &sc->sc_flags);
+ avp->primary_sta_vif = false;
+
+ if (ah->opmode == NL80211_IFTYPE_STATION)
+ clear_bit(SC_OP_BEACONS, &sc->sc_flags);
+ }
+
+ ieee80211_iterate_active_interfaces_atomic(sc->hw,
+ ath9k_bss_assoc_iter, sc);
- ath_dbg(common, CONFIG, "BSSID: %pM aid: 0x%x\n",
- common->curbssid, common->curaid);
+ if (!test_bit(SC_OP_PRIM_STA_VIF, &sc->sc_flags) &&
+ ah->opmode == NL80211_IFTYPE_STATION) {
+ memset(common->curbssid, 0, ETH_ALEN);
+ common->curaid = 0;
+ ath9k_hw_write_associd(sc->sc_ah);
+ }
}
if (changed & BSS_CHANGED_IBSS) {
- /* There can be only one vif available */
memcpy(common->curbssid, bss_conf->bssid, ETH_ALEN);
common->curaid = bss_conf->aid;
ath9k_hw_write_associd(sc->sc_ah);
if (bss_conf->ibss_joined) {
- sc->sc_ah->stats.avgbrssi = ATH_RSSI_DUMMY_MARKER;
-
if (!common->disable_ani) {
set_bit(SC_OP_ANI_RUN, &sc->sc_flags);
ath_start_ani(common);
}
-
} else {
clear_bit(SC_OP_ANI_RUN, &sc->sc_flags);
del_timer_sync(&common->ani.timer);
- del_timer_sync(&sc->rx_poll_timer);
}
}
--
1.7.11.2
reply other threads:[~2012-07-17 11:47 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20485.20590.137366.956003@gargle.gargle.HOWL \
--to=c_manoha@qca.qualcomm.com \
--cc=linux-wireless@vger.kernel.org \
--cc=linville@tuxdriver.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).