Linux wireless drivers development
 help / color / mirror / Atom feed
From: Bitterblue Smith <rtl8821cerfe2@gmail.com>
To: Daniel <dani069xp@gmail.com>, linux-wireless@vger.kernel.org
Cc: pkshih@realtek.com
Subject: Re: [Bug report] rtw89: 8851be: WiFi disconnect (reason=4, beacon loss) 1-2 s after A2DP stream start on the card's own Bluetooth, 5 GHz 80 MHz
Date: Fri, 20 Nov 2026 22:11:18 +0200	[thread overview]
Message-ID: <228ba38a-e5a2-4d8d-9547-788b9f0aec8a@gmail.com> (raw)
In-Reply-To: <CALovXdg6sOyK9orNrXSRSoSkVf7Adqa8xNC8Q=ESw4f0YEryaQ@mail.gmail.com>

On 20/11/2026 21:58, Daniel wrote:
> Hi,
> 
> On an RTL8851BE combo card, starting an A2DP audio stream on the card's own
> Bluetooth reliably makes the WiFi link drop within 1-2 seconds. The station is
> disconnected locally with reason=4 and the AP then ignores re-authentication
> for 50-90 s.
> 
> Hardware / software
> - WiFi: Realtek RTL8851BE PCIe 802.11ax [10ec:b851], driver rtw89_8851be
> - Bluetooth: USB 0bda:b850 (btusb, rtl_bt/rtl8851bu_fw.bin) on the same card
> - Firmware: rtw89/rtw8851b_fw-1.bin, version 0.29.41.5 (4bd6ebac)
> - linux-firmware 20261019
> - Kernel 7.3.5-zen1-1-zen (also seen on 7.3.4-zen2-1 and zen2-2), Arch Linux
> - NetworkManager 1.58.1, wpa_supplicant 2.12, bluez 5.88, PipeWire 1.6.11
> - Module options: rtw89_core disable_ps_mode=y,
>   rtw89_pci disable_aspm_l1=y disable_aspm_l1ss=y disable_clkreq=y (no effect)
> - NM: wifi.powersave=2, MAC randomization "stable"
> - AP: 5 GHz, channel 157, 80 MHz VHT; signal about -58 to -61 dBm, 1x1
> - BT audio: A2DP SBC to a headset (sink)
> 
> Observed
> bluetoothd logs "fd(N) ready" when the A2DP transport starts. In every case
> wpa_supplicant reports CTRL-EVENT-DISCONNECTED reason=4 locally_generated=1
> within 1-2 s:
> 
>   2026-11-14 13:08:32 BT stream  -> 13:08:34 WiFi drop (12 more drops
> while streaming)
>   2026-11-20 13:06:56 BT connect -> 13:07:04 WiFi drop; another at 13:47:54
>   2026-11-20 13:53:37 BT stream  -> 13:53:38 WiFi drop, reconnected 13:54:28
> 
> "iw dev wlp4s0 station dump" shows the beacon loss counter increasing with each
> event. ICMP loss to the AP is 0% outside these events and TX retries/failures
> are 0. Other devices on the same AP are not affected.
> 
> Width dependence
> - 80 MHz: 4 of 4 stream starts dropped the link.
> - 40 MHz (same AP, kernel, signal): 1 drop in 3 stream starts (2 were clean
>   over several days of use).
> - With Bluetooth off, 80 MHz showed no drops in the short test afterwards.
>   A USB-tethered phone on the same machine did not show the problem.
> 
> Not the cause (tested): browser/GPU, NetworkManager config, MAC randomization,
> power save, ASPM options, kernel 7.3.4 -> 7.3.5.
> 
> Expected: a stable WiFi link while Bluetooth A2DP streams, as it does on the
> same card with a narrower channel.
> 
> Coex trace around one drop (debugfs btc_info sampled every 0.5 s, local time,
> 5 GHz ch155 center, bw=2, 80 MHz; "iw event -t" in parallel)
> 
>   14:20:54.975  BT connect:Y (A2DP_active:Y from 14:20:55.5)
>   14:20:57.994  BT low-priority requests jump: Lo-rx/Lo-tx 0-3 -> 3064
>   14:20:59.504  BT profile:A2DP (bluetoothd: transport fd ready at 14:20:59)
>   14:21:00.830  iw event: CQM event: beacon loss
>   14:21:00.958  iw event: deauth reason 4 "Disassociated due to inactivity"
>                 (disconnected, local request)
>   14:21:01.020  coex: WL connect=NO_LINK, reason NTFY_POWEROFF, action WL_OFF
> 
> Second, independent capture of the same event (same setup, raw files kept):
> 
>   14:49:31.4    BT connect:Y
>   14:49:34.434  BT Lo-rx/Lo-tx requests jump 0-239 -> 3229
>   14:49:35      bluetoothd: A2DP transport fd ready
>   14:49:35.945  BT profile:A2DP
>   14:49:36.797  iw event: CQM event: beacon loss
>   14:49:36.910  iw event: deauth reason 4 "Disassociated due to inactivity"
>   14:49:36.952  coex: WL NO_LINK, action WL_OFF
>   14:50:13      WiFi connected again (about 36 s; "auth: timed out" x4 before)
> 
> In both captures the coex state is action:WL_5G, ant_path:FDD, tdma type:0
> right up to the last sample before the drop.
> 
> From 14:20:50 up to the drop the coex manager stays in action:WL_5G,
> ant_path:FDD, tdma type:0 the whole time, i.e. it does not arbitrate WL/BT
> while the BT traffic ramps up. hw_info reports ant_iso:10, rfe_type:0x2,
> tx_num:1, rx_num:1. WL_FW_coex 7.9.0 (desired 6.0.0, "Match"), BT_FW_coex 7.
> rssi was -54 dBm at the last sample before the drop (VHT MCS 9, 80 MHz).
> 
> For comparison, when the same station is on 2.4 GHz (ch 6, 20 MHz), A2DP
> streaming works for me without drops (user observation, not traced).
> The failing case is only 5 GHz + BT A2DP, and it is worse with 80 MHz than
> with 40 MHz.
> 
> Full btc_info trace, ser_counters (all 0) and the iw event log are available;
> I can send them or try patches/debug_mask settings. Thanks for any pointers.
> 
> Thanks,
> Dani

Hi,

The fix for this will be in kernel 7.4-rc4, and I think it will be added
automatically to 7.3 as well at some point:

https://lore.kernel.org/linux-wireless/E6568F470624C07E+179429427543.116514.14355630958613033614@guwolf.com/

  reply	other threads:[~2026-11-20 20:11 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-11-20 19:58 [Bug report] rtw89: 8851be: WiFi disconnect (reason=4, beacon loss) 1-2 s after A2DP stream start on the card's own Bluetooth, 5 GHz 80 MHz Daniel
2026-11-20 20:11 ` Bitterblue Smith [this message]
2026-11-20 20:20   ` Daniel

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=228ba38a-e5a2-4d8d-9547-788b9f0aec8a@gmail.com \
    --to=rtl8821cerfe2@gmail.com \
    --cc=dani069xp@gmail.com \
    --cc=linux-wireless@vger.kernel.org \
    --cc=pkshih@realtek.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox