From: Maciek Kaliszewski <mkalkal@interia.pl>
To: linux-wireless@vger.kernel.org
Subject: Kismet shows no clients (drivers iwl3945.ko or p54pci.ko)
Date: Thu, 10 Apr 2008 13:17:06 +0200 [thread overview]
Message-ID: <47FDF732.7000304@interia.pl> (raw)
Hi,
I have "02:00.0 Network controller: Intersil Corporation ISL3890 [Prism
GT/Prism Duette]/ISL3886 [Prism Javelin/Prism Xbow] (rev 01)"
which does not work with prism54.ko driver . So I have to use p54pci.ko
(from kernel 2.6.25-rc8) .
When I run kismet ,it detects wifi networks , but shows there is no
clients on the networks (I started data transfer on that network but it
didn't help)
Tcpdump on wlan0 interface (Monitor mode ) shows :
tcpdump: WARNING: wlan0: no IPv4 address assigned
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on wlan0, link-type IEEE802_11_RADIO (802.11 plus BSD radio
information header), capture size 96 bytes
12:38:51.010818 490951797us tsft 1.0 Mb/s 2457 MHz (0x0480) 81dB signal
[0x0000000e] Beacon (APTEKA) [1.0* 2.0* 5.5* 11.0* 18.0 24.0* 36.0 54.0
Mbit] ESS CH: 11, PRIVACY
12:38:51.317951 491258998us tsft 1.0 Mb/s 2457 MHz (0x0480) 83dB signal
[0x0000000e] Beacon (APTEKA) [1.0* 2.0* 5.5* 11.0* 18.0 24.0* 36.0 54.0
Mbit] ESS CH: 11, PRIVACY
12:38:51.625134 491566198us tsft 1.0 Mb/s 2457 MHz (0x0480) 79dB signal
[0x0000000e] Beacon (APTEKA) [1.0* 2.0* 5.5* 11.0* 18.0 24.0* 36.0 54.0
Mbit] ESS CH: 11, PRIVACY
12:38:51.932369 491873444us tsft 1.0 Mb/s 2457 MHz (0x0480) 79dB signal
[0x0000000e] Beacon (APTEKA) [1.0* 2.0* 5.5* 11.0* 18.0 24.0* 36.0 54.0
Mbit] ESS CH: 11, PRIVACY
12:38:52.034714 491975793us tsft 1.0 Mb/s 2457 MHz (0x0480) 83dB signal
[0x0000000e] Beacon (APTEKA) [1.0* 2.0* 5.5* 11.0* 18.0 24.0* 36.0 54.0
Mbit] ESS CH: 11, PRIVACY
12:38:52.137106 492078194us tsft 1.0 Mb/s 2457 MHz (0x0480) 88dB signal
[0x0000000e] Beacon (APTEKA) [1.0* 2.0* 5.5* 11.0* 18.0 24.0* 36.0 54.0
Mbit] ESS CH: 11, PRIVACY
12:38:52.239481 492180591us tsft 1.0 Mb/s 2457 MHz (0x0480) 74dB signal
[0x0000000e] Beacon (APTEKA) [1.0* 2.0* 5.5* 11.0* 18.0 24.0* 36.0 54.0
Mbit] ESS CH: 11, PRIVACY
12:38:52.341902 492282991us tsft 1.0 Mb/s 2457 MHz (0x0480) 84dB signal
[0x0000000e] Beacon (APTEKA) [1.0* 2.0* 5.5* 11.0* 18.0 24.0* 36.0 54.0
Mbit] ESS CH: 11, PRIVACY
12:38:52.444271 492385391us tsft 1.0 Mb/s 2457 MHz (0x0480) 80dB signal
[0x0000000e] Beacon (APTEKA) [1.0* 2.0* 5.5* 11.0* 18.0 24.0* 36.0 54.0
Mbit] ESS CH: 11, PRIVACY
12:38:52.649064 492590193us tsft 1.0 Mb/s 2457 MHz (0x0480) 82dB signal
[0x0000000e] Beacon (APTEKA) [1.0* 2.0* 5.5* 11.0* 18.0 24.0* 36.0 54.0
Mbit] ESS CH: 11, PRIVACY
12:38:52.751479 492692596us tsft 1.0 Mb/s 2457 MHz (0x0480) 81dB signal
[0x0000000e] Beacon (APTEKA) [1.0* 2.0* 5.5* 11.0* 18.0 24.0* 36.0 54.0
Mbit] ESS CH: 11, PRIVACY
12:38:52.853861 492794991us tsft 1.0 Mb/s 2457 MHz (0x0480) 68dB signal
[0x0000000e] Beacon (APTEKA) [1.0* 2.0* 5.5* 11.0* 18.0 24.0* 36.0 54.0
Mbit] ESS CH: 11, PRIVACY
12:38:52.956271 492897395us tsft 1.0 Mb/s 2457 MHz (0x0480) 68dB signal
[0x0000000e] Beacon (APTEKA) [1.0* 2.0* 5.5* 11.0* 18.0 24.0* 36.0 54.0
Mbit] ESS CH: 11, PRIVACY
12:38:53.161056 493102186us tsft 1.0 Mb/s 2457 MHz (0x0480) 88dB signal
[0x0000000e] Beacon (APTEKA) [1.0* 2.0* 5.5* 11.0* 18.0 24.0* 36.0 54.0
Mbit] ESS CH: 11, PRIVACY
12:38:53.263467 493204593us tsft 1.0 Mb/s 2457 MHz (0x0480) 87dB signal
[0x0000000e] Beacon (APTEKA) [1.0* 2.0* 5.5* 11.0* 18.0 24.0* 36.0 54.0
Mbit] ESS CH: 11, PRIVACY
12:38:53.365850 493306992us tsft 1.0 Mb/s 2457 MHz (0x0480) 86dB signal
[0x0000000e] Beacon (APTEKA) [1.0* 2.0* 5.5* 11.0* 18.0 24.0* 36.0 54.0
Mbit] ESS CH: 11, PRIVACY
12:38:53.468229 493409393us tsft 1.0 Mb/s 2457 MHz (0x0480) 78dB signal
[0x0000000e] Beacon (APTEKA) [1.0* 2.0* 5.5* 11.0* 18.0 24.0* 36.0 54.0
Mbit] ESS CH: 11, PRIVACY
As far as I can read the log , it show there is no traffic on net
APTEKA, but I know there is a data transfer on the net.
I had similar results on other computer ,intel wifi card with iwl3945.ko
driver(kernel 2.6.24.2).
Regards
Maciek
----------------------------------------------------------------------
Zadzwonila do chlopaka korzystajac z ...
Sprawdz >>> http://link.interia.pl/f1d8a
next reply other threads:[~2008-04-10 11:36 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-04-10 11:17 Maciek Kaliszewski [this message]
2008-04-10 18:16 ` Kismet shows no clients (drivers iwl3945.ko or p54pci.ko) Mike Kershaw
2008-04-11 14:50 ` Chatre, Reinette
2008-04-12 15:34 ` Mike Kershaw
2008-04-13 5:02 ` Mike Kershaw
-- strict thread matches above, loose matches on Subject: below --
2008-04-10 11:34 Maciek Kaliszewski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=47FDF732.7000304@interia.pl \
--to=mkalkal@interia.pl \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).