From: "Jerry Quinn (ibm)" <jlquinn@optonline.net>
To: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org, mcgrof@gmail.com, mickflemm@gmail.com
Subject: Re: ath5k can't connect on 5424
Date: Thu, 29 May 2008 11:10:10 -0400 [thread overview]
Message-ID: <483EC752.1040609@optonline.net> (raw)
In-Reply-To: <20080528002814.GF7779@tuxdriver.com>
John W. Linville wrote:
> On Sat, May 24, 2008 at 07:27:35PM -0400, Jerry Quinn wrote:
>
>> Hi. I just installed compat-wireless 2008-05-24.
>>
>> The good news is that ath5k now loads into the kernel and can talk to the
>> chip. However, beyond that, the device doesn't do anything. During
>> modprobe ath5k, I get
>>
>>
>> ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17
>> PCI: Setting latency timer of device 0000:03:00.0 to 64
>> ath5k_pci 0000:03:00.0: registered as 'phy1'
>> phy1: Selected rate control algorithm 'pid'
>> ath5k phy1: Atheros AR5424 chip found (MAC: 0xa3, PHY: 0x61)
>> udev: renamed network interface wlan0 to ath0
>>
>> The pci id for the chip is 168c:1014 (rev 01). This is an IBM Thinkpad
>> T60p, running Debian testing with kernel 2.6.25-2-686, the latest dist
>> kernel available.
>>
>> When I try to bring up the interface I just get a link is not ready message
>> in the kernel log with no other info. Also, iwlist ath0 scan gives me no
>> results either (I did ifconfig ath0 up beforehand).
>>
>> Let me know if there's any further diagnosis I can provide to help out.
>>
>
> You might wish to post the results of running the ath_info tool
> available from the madwifi project (sorry, I don't have the URL handy).
>
> John
>
Mike, thanks for pointing me to the updated ath_info.
Here's the dump from my chip:
naga:~/ath_info# ./ath_info -v 0xedf00000
#DBG main: sleep_ctl reg 00000000 reset_ctl reg 00000000
-==Device Information==-
MAC Version: 2424 (0xa0)
MAC Revision: 5424 (0xa3)
Warning: Invalid EEPROM Magic number!
Device type: 3
5GHz PHY Revision: SChip (0xa2)
2GHz PHY Revision: SChip (0xa2)
/============== EEPROM Information =============\
| EEPROM Version: 5.3 | EEPROM Size: 4 kbit |
| EEMAP: 2 | Reg. Domain: 0x62 |
|================= Capabilities ================|
| 802.11a Support: yes | Turbo-A disabled: yes |
| 802.11b Support: yes | Turbo-G disabled: yes |
| 802.11g Support: yes | 2GHz XR disabled: no |
| RFKill Support: yes | 5GHz XR disabled: no |
| 32kHz Crystal: no | |
\===============================================/
/=========================================================\
| Calibration data common for all modes |
|=========================================================|
| CCK/OFDM gain delta: 1 |
| CCK/OFDM power delta: 5 |
| Scaled CCK delta: 5 |
| 2GHz Antenna gain: 0 |
| 5GHz Antenna gain: 0 |
| Turbo 2W maximum dBm: 38 |
| Target power start: 0x1bd |
| EAR Start: 0x21f |
\=========================================================/
/=========================================================\
| Calibration data for 802.11a operation |
|=========================================================|
| I power: 0x08 | Q power: 0x1f |
| Use fixed bias: 0x00 | Max turbo power: 0x26 |
| Max XR power: 0x18 | Switch Settling Time: 0x2d |
| Tx/Rx attenuation: 0x2e | TX end to XLNA On: 0x02 |
| TX end to XPA Off: 0x00 | TX end to XPA On: 0x0e |
| 62db Threshold: 0x0f | XLNA gain: 0x0d |
| XPD: 0x01 | XPD gain: 0x0a |
| I gain: 0x00 | Tx/Rx margin: 0x13 |
| False detect backoff: 0x00 | Noise Floor Threshold: -54 |
| ADC desired size: -32 | PGA desired size: -80 |
|=========================================================|
| Antenna control 0: 0x00 | Antenna control 1: 0x01 |
| Antenna control 2: 0x26 | Antenna control 3: 0x26 |
| Antenna control 4: 0x06 | Antenna control 5: 0x06 |
| Antenna control 6: 0x02 | Antenna control 7: 0x25 |
| Antenna control 8: 0x25 | Antenna control 9: 0x05 |
| Antenna control 10: 0x05 | Antenna control 11: 0x00 |
|=========================================================|
| Octave Band 0: 5 | db 0: 5 |
| Octave Band 1: 5 | db 1: 5 |
| Octave Band 2: 5 | db 2: 5 |
| Octave Band 3: 5 | db 3: 5 |
\=========================================================/
/============== Per rate power calibration ===========\
| Freq | 6-24Mbit/s | 36Mbit/s | 48Mbit/s | 54Mbit/s |
|======|============|==========|===========|==========|
| 4920 | 12.00 | 12.00 | 12.00 | 8.00 |
|======|============|==========|===========|==========|
| 5080 | 12.00 | 12.00 | 12.00 | 8.00 |
|======|============|==========|===========|==========|
| 5170 | 16.00 | 16.00 | 14.00 | 13.00 |
|======|============|==========|===========|==========|
| 5240 | 16.00 | 16.00 | 14.00 | 13.00 |
|======|============|==========|===========|==========|
| 5260 | 17.00 | 16.00 | 14.00 | 13.00 |
|======|============|==========|===========|==========|
| 5700 | 17.00 | 16.00 | 14.00 | 13.00 |
|======|============|==========|===========|==========|
| 5745 | 16.00 | 15.00 | 14.00 | 11.00 |
|======|============|==========|===========|==========|
| 5825 | 16.00 | 15.00 | 14.00 | 11.00 |
|======|============|==========|===========|==========|
| 5360 | 18.00 | 18.00 | 18.00 | 18.00 |
|======|============|==========|===========|==========|
| 5720 | 18.00 | 18.00 | 18.00 | 18.00 |
\=====================================================/
/=================== Per channel power calibration ====================\
| Freq | pwr_0 | pwr_1 | pwr_2 | pwr_3 |pwrx3_0|pwrx3_1|pwrx3_2|max_pwr|
| | pcdac | pcdac | pcdac | pcdac | pcdac | pcdac | pcdac | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 5045 | 11.01 | 18.01 | 20.00 | 31.03 | 0.01 | 3.02 | 11.01 | 31.03 |
| | [25] | [44] | [48] | [63] | [20] | [35] | [63] | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 5185 | 5.00 | 18.02 | 21.02 | 25.00 | 42.02 | 46.01 | 51.01 | 25.00 |
| | [0] | [24] | [27] | [30] | [20] | [35] | [63] | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 5220 | 8.00 | 32.00 | 17.00 | 18.02 | 1.00 | 10.02 | 26.01 | 18.02 |
| | [153] | [178] | [198] | [208] | [20] | [35] | [63] | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 5435 | 21.01 | 6.03 | 32.00 | 32.00 | 34.01 | 42.02 | 1.02 | 32.00 |
| | [50] | [54] | [72] | [103] | [20] | [35] | [63] | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 5535 | 22.00 | 55.01 | 17.03 | 4.01 | 18.01 | 24.02 | 2.01 | 4.01 |
| | [171] | [171] | [173] | [177] | [20] | [35] | [63] | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 5100 | 1.01 | 12.02 | 10.00 | 54.01 | 24.00 | 36.00 | 18.02 | 54.01 |
| | [98] | [119] | [145] | [150] | [20] | [35] | [63] | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 4825 | 54.01 | 42.02 | 1.01 | 11.02 | 25.01 | 6.03 | 32.00 | 11.02 |
| | [144] | [167] | [175] | [197] | [20] | [35] | [63] | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 4890 | 18.02 | 28.02 | 34.01 | 10.02 | 13.03 | 55.01 | 21.02 | 10.02 |
| | [22] | [28] | [44] | [54] | [20] | [35] | [63] | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 5045 | 24.00 | 32.00 | 18.02 | 28.02 | 1.02 | 11.02 | 5.03 | 28.02 |
| | [161] | [186] | [205] | [215] | [20] | [35] | [63] | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 4925 | 17.03 | 5.03 | 16.00 | 36.00 | 26.01 | 42.02 | 1.02 | 36.00 |
| | [46] | [60] | [78] | [107] | [20] | [35] | [63] | |
\======================================================================/
/=========================================================\
| Calibration data for 802.11b operation |
|=========================================================|
| I power: 0x00 | Q power: 0x00 |
| Use fixed bias: 0x00 | Max turbo power: 0x00 |
| Max XR power: 0x00 | Switch Settling Time: 0x28 |
| Tx/Rx attenuation: 0x1c | TX end to XLNA On: 0x02 |
| TX end to XPA Off: 0x00 | TX end to XPA On: 0x07 |
| 62db Threshold: 0x1c | XLNA gain: 0x0d |
| XPD: 0x01 | XPD gain: 0x0a |
| I gain: 0x00 | Tx/Rx margin: 0x14 |
| False detect backoff: 0x00 | Noise Floor Threshold: -1 |
| ADC desired size: -62 | PGA desired size: -104 |
|=========================================================|
| Antenna control 0: 0x00 | Antenna control 1: 0x0d |
| Antenna control 2: 0x2a | Antenna control 3: 0x2a |
| Antenna control 4: 0x22 | Antenna control 5: 0x22 |
| Antenna control 6: 0x0e | Antenna control 7: 0x29 |
| Antenna control 8: 0x29 | Antenna control 9: 0x21 |
| Antenna control 10: 0x21 | Antenna control 11: 0x00 |
|=========================================================|
| Octave Band 0: 5 | db 0: 5 |
| Octave Band 1: 5 | db 1: 5 |
| Octave Band 2: 0 | db 2: 0 |
| Octave Band 3: 0 | db 3: 0 |
\=========================================================/
/=================== Per channel power calibration ====================\
| Freq | pwr_0 | pwr_1 | pwr_2 | pwr_3 |pwrx3_0|pwrx3_1|pwrx3_2|max_pwr|
| | pcdac | pcdac | pcdac | pcdac | pcdac | pcdac | pcdac | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 2412 | 6.00 | 22.01 | 21.02 | 6.03 | 18.01 | 31.02 | 30.01 | 6.03 |
| | [170] | [170] | [174] | [178] | [20] | [35] | [63] | |
\======================================================================/
/=========================================================\
| Calibration data for 802.11g operation |
|=========================================================|
| I power: 0x00 | Q power: 0x10 |
| Use fixed bias: 0x01 | Max turbo power: 0x26 |
| Max XR power: 0x24 | Switch Settling Time: 0x28 |
| Tx/Rx attenuation: 0x1c | TX end to XLNA On: 0x02 |
| TX end to XPA Off: 0x00 | TX end to XPA On: 0x0e |
| 62db Threshold: 0x1c | XLNA gain: 0x0d |
| XPD: 0x01 | XPD gain: 0x0a |
| I gain: 0x00 | Tx/Rx margin: 0x14 |
| False detect backoff: 0x00 | Noise Floor Threshold: -1 |
| ADC desired size: -40 | PGA desired size: -105 |
|=========================================================|
| Antenna control 0: 0x00 | Antenna control 1: 0x0d |
| Antenna control 2: 0x2a | Antenna control 3: 0x2a |
| Antenna control 4: 0x22 | Antenna control 5: 0x22 |
| Antenna control 6: 0x0e | Antenna control 7: 0x29 |
| Antenna control 8: 0x29 | Antenna control 9: 0x21 |
| Antenna control 10: 0x21 | Antenna control 11: 0x05 |
|=========================================================|
| Octave Band 0: 5 | db 0: 5 |
| Octave Band 1: 5 | db 1: 5 |
| Octave Band 2: 0 | db 2: 0 |
| Octave Band 3: 0 | db 3: 0 |
\=========================================================/
/=================== Per channel power calibration ====================\
| Freq | pwr_0 | pwr_1 | pwr_2 | pwr_3 |pwrx3_0|pwrx3_1|pwrx3_2|max_pwr|
| | pcdac | pcdac | pcdac | pcdac | pcdac | pcdac | pcdac | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 2412 | 1.02 | 11.02 | 61.03 | 23.00 | 32.00 | 36.00 | 17.02 | 23.00 |
| | [98] | [121] | [123] | [129] | [20] | [35] | [63] | |
\======================================================================/
GPIO registers: CR 0x00018003, DO 0x00000001, DI 0x0000000b
STA_ID0: 00:16:cf:23:6f:9e
STA_ID1: 0x1b809e6f, AP: 0, IBSS: 0, KeyCache Disable: 0
TIMER0: 0x00000030, TBTT: 48, TU: 0x00070030
TIMER1: 0x0007ffff, DMAb: 65535, TU: 0x0006ffff (-49)
TIMER2: 0x01ffffff, SWBA: 65535, TU: 0x003fffff (+3735503)
TIMER3: 0x00000031, ATIM: 49, TU: 0x00070031 (+1)
TSF: 0x000000001a8bf0f6, TSFTU: 41724, TU: 0x0006a2fc
BEACON: 0x00000000
LAST_TSTP: 0x007fe01f
next prev parent reply other threads:[~2008-05-29 15:10 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-05-24 23:27 ath5k can't connect on 5424 Jerry Quinn
2008-05-28 0:28 ` John W. Linville
2008-05-29 4:57 ` Michael Renzmann
2008-05-29 15:10 ` Jerry Quinn (ibm) [this message]
2008-05-29 18:52 ` Pavel Roskin
2008-05-29 19:18 ` Bob Copeland
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=483EC752.1040609@optonline.net \
--to=jlquinn@optonline.net \
--cc=linux-wireless@vger.kernel.org \
--cc=linville@tuxdriver.com \
--cc=mcgrof@gmail.com \
--cc=mickflemm@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).