linux-wireless.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Dave <kilroyd@googlemail.com>
To: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: linux-wireless@vger.kernel.org, linux-pcmcia@lists.infradead.org,
	orinoco-devel@lists.sourceforge.net
Subject: Re: [Orinoco-devel] 2.6.28-rc2: new PCMCIA device instance after resume - orinoco can't download firmware
Date: Wed, 29 Oct 2008 00:49:18 +0000	[thread overview]
Message-ID: <4907B30E.90109@gmail.com> (raw)
In-Reply-To: <200810282219.51492.arvidjaar@mail.ru>

Andrey Borzenkov wrote:
> I am running PCMCIA based orinoco with WPA support (external firmware)
> and two patches to cache it after request_firmware to use in resume.
> 
> This worked fine in 27 and wtopped working in 28-rc. The apparent difference
> I see:

I'm seeing the same, but my laptop has never resumed very well so I put
it down to the preceding errors (which you don't have):

Oct 29 00:00:17 borken Back to C!
Oct 29 00:00:17 borken ACPI: Waking up from system sleep state S3
Oct 29 00:00:17 borken ACPI Warning (nspredef-0852): \_WAK: Return type
mismatch - found Integer, expected Package [20080926]
Oct 29 00:00:17 borken agpgart-intel 0000:00:00.0: restoring config
space at offset 0x1 (was 0x22100006, writing 0x22100106)
Oct 29 00:00:17 borken pm_op(): pci_pm_resume+0x0/0x46 returns -16
Oct 29 00:00:17 borken PM: Device 0000:00:00.0 failed to resume: error -16
Oct 29 00:00:17 borken pcmcia 0.0: pcmcia: registering new device pcmcia0.0
Oct 29 00:00:17 borken dhcpcd[6661]: eth1: carrier lost
Oct 29 00:00:17 borken eth1: Hardware identity 0001:0001:0004:0002
Oct 29 00:00:17 borken eth1: Station identity  001f:0001:0008:0048
Oct 29 00:00:17 borken eth1: Firmware determined as Lucent/Agere 8.72
Oct 29 00:00:17 borken eth1: Attempting to download firmware
agere_sta_fw.bin
Oct 29 00:00:17 borken hermes_dld: AUX enable returned 0
Oct 29 00:00:17 borken hermes_dld: AUX disable returned 0
Oct 29 00:00:17 borken hermes_dld: Actual PDA length 998, Max allowed 1000
Oct 29 00:00:17 borken eth1: Read PDA returned 0
Oct 29 00:00:17 borken orinoco_cs 0.0: firmware: requesting agere_sta_fw.bin
Oct 29 00:00:17 borken eth1: Cannot find firmware agere_sta_fw.bin


Dave.

> [  617.975868] Back to C!
> [  617.987166] ACPI: Waking up from system sleep state S3
> [  618.004377] pci 0000:00:01.0: setting latency timer to 64
 <snip>
> [  619.323782] pcmcia 0.0: pcmcia: registering new device pcmcia0.0
> [  619.404234] eth1: Hardware identity 0005:0002:0001:0002
> [  619.404345] eth1: Station identity  001f:0001:0006:000e
> [  619.404356] eth1: Firmware determined as Lucent/Agere 6.14
> [  619.404369] eth1: Attempting to download firmware agere_sta_fw.bin
> [  619.404398] hermes_dld: AUX enable returned 0
> [  619.405440] hermes_dld: AUX disable returned 0
> [  619.405448] hermes_dld: Actual PDA length 998, Max allowed 1000
> [  619.405454] eth1: Read PDA returned 0
> [  619.405464] orinoco_cs 0.0: firmware: requesting agere_sta_fw.bin
> [  620.257118] ata1.00: ACPI cmd ef/03:0c:00:00:00:00 filtered out
> [  620.257128] ata1.00: ACPI cmd ef/03:44:00:00:00:00 filtered out
> [  620.272387] ata1.00: configured for UDMA/33
> [  620.272634] sd 0:0:0:0: [sda] 39070080 512-byte hardware sectors: (20.0 GB/18.6 GiB)
> [  620.272723] sd 0:0:0:0: [sda] Write Protect is off
> [  620.272733] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [  620.272861] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [  679.403515] eth1: Cannot find firmware agere_sta_fw.bin
> [  679.403593] eth1: Hardware identity 0005:0002:0001:0002
> [  679.403704] eth1: Station identity  001f:0001:0006:000e
> [  679.403714] eth1: Firmware determined as Lucent/Agere 6.14
> [  679.403721] eth1: Ad-hoc demo mode supported
> [  679.403727] eth1: IEEE standard IBSS ad-hoc mode supported
> [  679.403733] eth1: WEP supported, 104-bit key
> [  679.403856] eth1: MAC address 00:02:2d:26:95:6c
> [  679.403962] eth1: Station name "HERMES I"
> [  679.404529] eth1: ready
> [  679.405117] eth1: orinoco_cs at 0.0, irq 11, io 0x0100-0x013f
> [  679.676707] pci 0000:00:12.0: restoring config space at offset 0xf (was 0x1ff, writing 0x10b)
> [  679.676785] pci 0000:01:00.0: restoring config space at offset 0xf (was 0x1ff, writing 0x10b)
> [  679.680310] sd 0:0:0:0: [sda] Starting disk
> [  680.109195] Restarting tasks ... done.
> [  681.184812] eth1: New link status: Disconnected (0002)
> [  688.967595] eth1: New link status: Disconnected (0002)

      parent reply	other threads:[~2008-10-29  0:49 UTC|newest]

Thread overview: 14+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2008-10-28 19:19 2.6.28-rc2: new PCMCIA device instance after resume - orinoco can't download firmware Andrey Borzenkov
2008-10-29  0:42 ` Dominik Brodowski
2008-10-29  3:43   ` Andrey Borzenkov
2008-10-29 12:18     ` Rafael J. Wysocki
2008-10-29 15:19       ` Andrey Borzenkov
2008-10-29 18:49         ` [Orinoco-devel] " Dave
2008-10-29 20:43           ` Rafael J. Wysocki
2008-10-29 20:53             ` Dave
2008-10-29 21:34               ` Rafael J. Wysocki
2008-10-29 21:51               ` Russell King
2008-10-30 18:15                 ` Dave
2008-10-30 18:39                   ` Andrey Borzenkov
2008-10-30 22:46                     ` Rafael J. Wysocki
2008-10-29  0:49 ` Dave [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=4907B30E.90109@gmail.com \
    --to=kilroyd@googlemail.com \
    --cc=arvidjaar@mail.ru \
    --cc=linux-pcmcia@lists.infradead.org \
    --cc=linux-wireless@vger.kernel.org \
    --cc=orinoco-devel@lists.sourceforge.net \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).