From: Ivan Kuten <ivan.kuten@promwad.com>
To: linux-wireless@vger.kernel.org
Cc: "Luis R. Rodriguez" <mcgrof@gmail.com>
Subject: Re: WPA2, compat-wireless-2.6.31-rc3, kernel 2.6.28 - rtl8187 - association works but no ping
Date: Fri, 24 Jul 2009 11:13:39 +0300 [thread overview]
Message-ID: <4A696D33.8050606@promwad.com> (raw)
In-Reply-To: <43e72e890907230917w226c4697v41f907623e5f7d8@mail.gmail.com>
> On Thu, Jul 23, 2009 at 2:22 AM, Ivan Kuten<ivan.kuten@promwad.com> wrote:
>> compat-wireless-2.6.31-rc3
>
> compat-wireless-2.6.31-rc4 is out, please try that.
>
> Luis
>
Here is what I get for compat-wireless-2.6.31-rc4:
<6>cfg80211: Using static regulatory domain info
<6>cfg80211: Regulatory domain: US
<6> (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6> (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
<6> (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
<6> (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
<6> (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
<6> (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
<6> (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
<6>usb 1-1: new high speed USB device using isp1761 and address 2
<6>cfg80211: Calling CRDA for country: US
<6>usbcore: registered new interface driver rtl8187
<6>usb 1-1: configuration #1 chosen from 1 choice
<6>hub 1-1:1.0: USB hub found
<6>hub 1-1:1.0: 3 ports detected
<6>usb 1-1.1: new high speed USB device using isp1761 and address 3
<6>usb 1-1.1: configuration #1 chosen from 1 choice
<7>phy0: Selected rate control algorithm 'minstrel'
<6>phy0: hwaddr 00277080, RTL8187vB (default) V1 + rtl8225z2
<7>phy0: device now idle
<7>phy0: device no longer idle - scanning
<7>phy0: device now idle
<7>phy0: device no longer idle - in use
<7>wlan0: authenticate with AP 01a4b568
<7>wlan0: authenticated
<7>wlan0: associate with AP 01a4b568
<7>wlan0: RX AssocResp from 003e101a (capab=0x411 status=0 aid=2)
<7>wlan0: associated
<7>phy0: Allocated STA 002fbfc4
<7>phy0: Inserted STA 002fbfc4
<7>wlan0: switched to short slot time (BSSID=01a4b568)
iwconfig output:
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11bg ESSID:"ACORP"
Mode:Managed Frequency:2.462 GHz Access Point: 00:02:72:74:AC:85
Bit Rate=1 Mb/s Tx-Power=27 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:2BAC-63B9-5D99-CF9A-4D39-079F-BB55-5D39 [2]
Power Management:off
Link Quality=61/70 Signal level=-49 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
ifconfig:
eth0 Link encap:Ethernet HWaddr 02:80:AD:20:31:EB
inet addr:192.168.5.1 Bcast:192.168.5.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:40 errors:0 dropped:0 overruns:0 frame:0
TX packets:188 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:4077 (3.9 KiB) TX bytes:17012 (16.6 KiB)
wlan0 Link encap:Ethernet HWaddr 00:12:0E:98:67:FC
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:304 (304.0 B) TX bytes:3932 (3.8 KiB)
wmaster0 Link encap:UNSPEC HWaddr 00-12-0E-98-67-FC-00-00-00-00-00-00-00-00-00-00
UP RUNNING MTU:0 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Neither dhcp nor setting static IP for wlan0 - no ping.
Regards,
Ivan
next prev parent reply other threads:[~2009-07-24 8:13 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-07-23 9:22 WPA2, compat-wireless-2.6.31-rc3, kernel 2.6.28 - rtl8187 - association works but no ping Ivan Kuten
2009-07-23 16:17 ` Luis R. Rodriguez
2009-07-24 8:13 ` Ivan Kuten [this message]
2009-07-24 15:24 ` Luis R. Rodriguez
2009-07-24 15:52 ` Ivan Kuten
2009-07-24 16:23 ` Luis R. Rodriguez
2009-07-24 16:40 ` Ivan Kuten
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4A696D33.8050606@promwad.com \
--to=ivan.kuten@promwad.com \
--cc=linux-wireless@vger.kernel.org \
--cc=mcgrof@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).