Re: rt61pci bug

[Tim Blechmann <tim@klingt.org>]

[-- Attachment #1: Type: text/plain, Size: 3935 bytes --]

On 11/04/2009 07:00 PM, Tim Blechmann wrote:
>> running the rt61pci module on 2.6.31.5 works fine, but using the recent 
>> linus/master (2.6.32-rc5) results in this:
> 
> same issue with 2.6.32-rc5 ... new bootlog with more debugging info
> attached ...

i was still able to reproduce this issue with 2.6.32-rc8 ... it would 
be nice, if someone could have a look into this issue before 2.6.32 is 
released ...

dmesg from 2.6.32-rc8:
[   10.249098] rt61pci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   10.257182] phy0 -> rt61pci_validate_eeprom: EEPROM recovery - NIC: 0xff80
[   10.257184] phy0 -> rt61pci_validate_eeprom: EEPROM recovery - Led: 0xe0ff
[   10.257187] phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 0302, rf: 0003, rev: 0002561c.
[   10.351794] Registered led device: rt61pci-phy0::radio
[   10.351839] Registered led device: rt61pci-phy0::assoc
[   14.342046] rt61pci 0000:06:00.0: firmware: requesting rt2561.bin
[   14.395533] phy0 -> rt2x00lib_request_firmware: Info - Firmware detected - version: 0.8.
[   14.421238] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 102.
[   14.421245] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 4, CWmax: 5, Aifs: 2, TXop: 188.
[   14.421252] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 5, CWmax: 10, Aifs: 3, TXop: 0.
[   14.421258] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 5, CWmax: 10, Aifs: 7, TXop: 0.
[  273.404685] phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2.
[  273.404687] Please file bug report to http://rt2x00.serialmonkey.com.
[  282.143549] wlan0: no IPv6 routers present
[  357.304908] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 2
[  357.333806] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 9
[  360.172776] phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2.
[  360.172778] Please file bug report to http://rt2x00.serialmonkey.com.
[  360.172782] phy0 -> rt2x00mac_tx_rts_cts: Warning - Failed to send RTS/CTS frame.
[  383.880010] No probe response from AP 00:24:fe:09:94:18 after 500ms, disconnecting.
[  383.880026] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
[  383.880034] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
[  383.880042] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
[  383.880050] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
[  385.220460] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 1)
[  385.421337] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 2)
[  385.621304] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 3)
[  385.821264] wlan0: direct probe to AP 00:24:fe:09:94:18 timed out


lspci -vvv:

06:00.0 Network controller: RaLink RT2561/RT61 rev B 802.11g
	Subsystem: D-Link System Inc Device 3c09
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at fb6f8000 (32-bit, non-prefetchable) [size=32K]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: rt61pci
	Kernel modules: rt61pci

thanks, tim

-- 
tim@klingt.org
http://tim.klingt.org

Happiness is a byproduct of function, purpose, and conflict; those who
seek happiness for itself seek victory without war.
  William S. Burroughs


[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 197 bytes --]