From: Jan Martinek <honza@dp.fce.vutbr.cz>
To: linux-wireless@vger.kernel.org
Subject: ISL3890, master mode, prism54 -> p54pci regression
Date: Sat, 13 Mar 2010 08:50:08 +0100 [thread overview]
Message-ID: <4B9B43B0.1030801@dp.fce.vutbr.cz> (raw)
Hello,
I have been using prism54 driver and my PCI wireless card was working in
Master mode. After upgrade to kernel-2.6.32 there is no prism54 driver
so I switched to p54pci. The problem is that I cannot set the Master
mode anymore, I get this error:
# iwconfig wlan0 mode master
Error for wireless request "Set Mode" (8B06) :
SET failed on device wlan0 ; Invalid argument.
This is my wireless card:
03:05.0 Network controller: Intersil Corporation ISL3890 [Prism GT/Prism
Duette]/ISL3886 [Prism Javelin/Prism Xbow] (rev 01)
this is my kernel version: kernel-2.6.32.9-70.fc12.x86_64
And here is what I found in dmesg:
cfg80211: World regulatory domain updated:
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
p54pci 0000:03:05.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
p54pci 0000:03:05.0: firmware: requesting isl3886pci
phy0: p54 detected a LM86 firmware
p54: rx_mtu reduced from 3240 to 2376
phy0: FW rev 2.13.12.0 - Softmac protocol 5.9
phy0: cryptographic accelerator WEP:YES, TKIP:YES, CCMP:YES
phy0: hwaddr 00:60:b3:1c:41:e5, MAC:isl3890 RF:Frisbee
phy0: Selected rate control algorithm 'minstrel'
Registered led device: p54-phy0::assoc
Registered led device: p54-phy0::tx
Registered led device: p54-phy0::rx
Registered led device: p54-phy0::radio
p54pci 0000:03:05.0: is registered as 'phy0'
cfg80211: Calling CRDA for country: CZ
cfg80211: Regulatory domain changed to country: CZ
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
(5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2301 mBm)
(5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2301 mBm)
(5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Is there any possibility to set the master mode?
Thank you,
Jan Martinek
next reply other threads:[~2010-03-13 8:05 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-03-13 7:50 Jan Martinek [this message]
2010-03-13 10:10 ` ISL3890, master mode, prism54 -> p54pci regression Luis R. Rodriguez
2010-03-13 10:26 ` Christian Lamparter
2010-03-15 8:08 ` Jan Martinek
2010-03-15 11:39 ` Christian Lamparter
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4B9B43B0.1030801@dp.fce.vutbr.cz \
--to=honza@dp.fce.vutbr.cz \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).