* Hostapd + wpa_supplicant @ 2010-11-29 4:13 linux newbie 2010-11-30 3:33 ` linux newbie 0 siblings, 1 reply; 5+ messages in thread From: linux newbie @ 2010-11-29 4:13 UTC (permalink / raw) To: hostap, linux-wireless Hi, * On my embedded target, I am running rt73 based usb wireless adapter. * tested hostapd and wpa_supplicant individually and it is working fine. * bothe hostapd and wpa_supplicant are latest 0.7.3 versions with libnl_1.1 version & kernel 2.6.35 If I run both wpa_supplicant and hostapd I am having issue. Reason for running hostapd and wpa_supplicant on same terminal is we have multiple wireless terminals and if one of them can't access the AP (due to coverage issue) , then it will bind to Hostapd on some other terminal. I am not sure, if I can able to configure my terminals to use both hostapd & wpa_supplicant and need your expert advice. Thanks ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Hostapd + wpa_supplicant 2010-11-29 4:13 Hostapd + wpa_supplicant linux newbie @ 2010-11-30 3:33 ` linux newbie 2010-11-30 8:38 ` Dennis Borgmann 0 siblings, 1 reply; 5+ messages in thread From: linux newbie @ 2010-11-30 3:33 UTC (permalink / raw) To: hostap, linux-wireless Hi, Any suggestion? Thanks On Mon, Nov 29, 2010 at 3:13 PM, linux newbie <linux.newbie79@gmail.com> wrote: > Hi, > > * On my embedded target, I am running rt73 based usb wireless adapter. > * tested hostapd and wpa_supplicant individually and it is working fine. > * bothe hostapd and wpa_supplicant are latest 0.7.3 versions with > libnl_1.1 version & kernel 2.6.35 > > If I run both wpa_supplicant and hostapd I am having issue. > > Reason for running hostapd and wpa_supplicant on same terminal is we > have multiple wireless terminals and if one of them can't access the > AP (due to coverage issue) , then it will bind to Hostapd on some > other terminal. I am not sure, if I can able to configure my terminals > to use both hostapd & wpa_supplicant and need your expert advice. > > Thanks > ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Hostapd + wpa_supplicant 2010-11-30 3:33 ` linux newbie @ 2010-11-30 8:38 ` Dennis Borgmann 2010-11-30 9:12 ` linux newbie 0 siblings, 1 reply; 5+ messages in thread From: Dennis Borgmann @ 2010-11-30 8:38 UTC (permalink / raw) To: linux newbie; +Cc: hostap, linux-wireless Hello linux newbie! It is not quite clear from your message, what you would like to do. Are you running only one wireless device within your embedded target? If so, it is not possible to run hostapd and wpa_supplicant at the same time, since the wireless card can only work in either AP or station mode. Both at the same time is not possible. So what you would need to do is write scripts, that kill the station mode, create an AP mode or the other way around depending on what you need at a defined point of time. If you want to run hostapd and wpa_supplicant at the very same time, for your embedded target to be an AP and a station at the very same moment, you will need to run two wireless interfaces on your target. HTH, Dennis Borgmann linux newbie schrieb: > Hi, > > Any suggestion? > > Thanks > > On Mon, Nov 29, 2010 at 3:13 PM, linux newbie <linux.newbie79@gmail.com> wrote: > >> Hi, >> >> * On my embedded target, I am running rt73 based usb wireless adapter. >> * tested hostapd and wpa_supplicant individually and it is working fine. >> * bothe hostapd and wpa_supplicant are latest 0.7.3 versions with >> libnl_1.1 version & kernel 2.6.35 >> >> If I run both wpa_supplicant and hostapd I am having issue. >> >> Reason for running hostapd and wpa_supplicant on same terminal is we >> have multiple wireless terminals and if one of them can't access the >> AP (due to coverage issue) , then it will bind to Hostapd on some >> other terminal. I am not sure, if I can able to configure my terminals >> to use both hostapd & wpa_supplicant and need your expert advice. >> >> Thanks >> >> > _______________________________________________ > HostAP mailing list > HostAP@lists.shmoo.com > http://lists.shmoo.com/mailman/listinfo/hostap > ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Hostapd + wpa_supplicant 2010-11-30 8:38 ` Dennis Borgmann @ 2010-11-30 9:12 ` linux newbie 2010-11-30 10:03 ` Dennis Borgmann 0 siblings, 1 reply; 5+ messages in thread From: linux newbie @ 2010-11-30 9:12 UTC (permalink / raw) To: Dennis Borgmann; +Cc: hostap, linux-wireless Hi Dennis, Thanks for your reply. * My embedded device (wireless terminal) has only one network interface. I am currently trying to do following setup. * We have wireless terminals communicating to AP. * There are situations in which some terminals goes out of coverage. * We like to enable AP (in repeater or bridge mode) in our terminals, so that out-of-coverage terminals can communicate with other terminals which has coverage. * So that we can maintain the coverage all the time. Please let me know, if this is possible to achieve. Thanks On Tue, Nov 30, 2010 at 7:38 PM, Dennis Borgmann <dennis.borgmann@googlemail.com> wrote: > Hello linux newbie! > > It is not quite clear from your message, what you would like to do. Are > you running only one wireless device within your embedded target? If so, > it is not possible to run hostapd and wpa_supplicant at the same time, > since the wireless card can only work in either AP or station mode. Both > at the same time is not possible. So what you would need to do is write > scripts, that kill the station mode, create an AP mode or the other way > around depending on what you need at a defined point of time. > > If you want to run hostapd and wpa_supplicant at the very same time, for > your embedded target to be an AP and a station at the very same moment, > you will need to run two wireless interfaces on your target. > > HTH, > Dennis Borgmann > > linux newbie schrieb: >> Hi, >> >> Any suggestion? >> >> Thanks >> >> On Mon, Nov 29, 2010 at 3:13 PM, linux newbie <linux.newbie79@gmail.com> wrote: >> >>> Hi, >>> >>> * On my embedded target, I am running rt73 based usb wireless adapter. >>> * tested hostapd and wpa_supplicant individually and it is working fine. >>> * bothe hostapd and wpa_supplicant are latest 0.7.3 versions with >>> libnl_1.1 version & kernel 2.6.35 >>> >>> If I run both wpa_supplicant and hostapd I am having issue. >>> >>> Reason for running hostapd and wpa_supplicant on same terminal is we >>> have multiple wireless terminals and if one of them can't access the >>> AP (due to coverage issue) , then it will bind to Hostapd on some >>> other terminal. I am not sure, if I can able to configure my terminals >>> to use both hostapd & wpa_supplicant and need your expert advice. >>> >>> Thanks >>> >>> >> _______________________________________________ >> HostAP mailing list >> HostAP@lists.shmoo.com >> http://lists.shmoo.com/mailman/listinfo/hostap >> > > ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Hostapd + wpa_supplicant 2010-11-30 9:12 ` linux newbie @ 2010-11-30 10:03 ` Dennis Borgmann 0 siblings, 0 replies; 5+ messages in thread From: Dennis Borgmann @ 2010-11-30 10:03 UTC (permalink / raw) To: linux newbie; +Cc: hostap, linux-wireless Hi linux newbie! You want a wireless mesh: http://en.wikipedia.org/wiki/802.11s http://en.wikipedia.org/wiki/Wireless_mesh_network I just found those two articles, but searching the Internet for "802.11s" or "wireless mesh" or whatever will give you an enormous amount of information about meshing. Kind regards, Dennis Borgmann linux newbie schrieb: > Hi Dennis, > > Thanks for your reply. > > * My embedded device (wireless terminal) has only one network interface. > > I am currently trying to do following setup. > > * We have wireless terminals communicating to AP. > * There are situations in which some terminals goes out of coverage. > * We like to enable AP (in repeater or bridge mode) in our terminals, > so that out-of-coverage terminals can communicate with other terminals > which has coverage. > * So that we can maintain the coverage all the time. > > Please let me know, if this is possible to achieve. > > Thanks > > On Tue, Nov 30, 2010 at 7:38 PM, Dennis Borgmann > <dennis.borgmann@googlemail.com> wrote: > >> Hello linux newbie! >> >> It is not quite clear from your message, what you would like to do. Are >> you running only one wireless device within your embedded target? If so, >> it is not possible to run hostapd and wpa_supplicant at the same time, >> since the wireless card can only work in either AP or station mode. Both >> at the same time is not possible. So what you would need to do is write >> scripts, that kill the station mode, create an AP mode or the other way >> around depending on what you need at a defined point of time. >> >> If you want to run hostapd and wpa_supplicant at the very same time, for >> your embedded target to be an AP and a station at the very same moment, >> you will need to run two wireless interfaces on your target. >> >> HTH, >> Dennis Borgmann >> >> linux newbie schrieb: >> >>> Hi, >>> >>> Any suggestion? >>> >>> Thanks >>> >>> On Mon, Nov 29, 2010 at 3:13 PM, linux newbie <linux.newbie79@gmail.com> wrote: >>> >>> >>>> Hi, >>>> >>>> * On my embedded target, I am running rt73 based usb wireless adapter. >>>> * tested hostapd and wpa_supplicant individually and it is working fine. >>>> * bothe hostapd and wpa_supplicant are latest 0.7.3 versions with >>>> libnl_1.1 version & kernel 2.6.35 >>>> >>>> If I run both wpa_supplicant and hostapd I am having issue. >>>> >>>> Reason for running hostapd and wpa_supplicant on same terminal is we >>>> have multiple wireless terminals and if one of them can't access the >>>> AP (due to coverage issue) , then it will bind to Hostapd on some >>>> other terminal. I am not sure, if I can able to configure my terminals >>>> to use both hostapd & wpa_supplicant and need your expert advice. >>>> >>>> Thanks >>>> >>>> >>>> >>> _______________________________________________ >>> HostAP mailing list >>> HostAP@lists.shmoo.com >>> http://lists.shmoo.com/mailman/listinfo/hostap >>> >>> >> ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2010-11-30 10:03 UTC | newest] Thread overview: 5+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2010-11-29 4:13 Hostapd + wpa_supplicant linux newbie 2010-11-30 3:33 ` linux newbie 2010-11-30 8:38 ` Dennis Borgmann 2010-11-30 9:12 ` linux newbie 2010-11-30 10:03 ` Dennis Borgmann
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).